Dedicated Micros CamVu 720 Manuale
Installation Guide
CamVu 720
Installation and
Conguration Manual
DM/CMVU720
DM/CMVU7200/N
2CamVu 720
Contents
Important Safeguards....................................................................... 5
Mounting External Domes .............................................................. 14
Conguring the Unit........................................................................ 19
System ........................................................................................... 22
Display............................................................................................ 40
Camera........................................................................................... 45
Dome Settings................................................................................ 46
ICR Settings ................................................................................... 59
Schedule ........................................................................................ 71
Alarm Settings ...................................................................................... 76
Network Settings ............................................................................ 88
Diagnostics................................................................................... 102
Unit Operation .............................................................................. 105
Operating the Viewer.................................................................... 106
Appendix A - Unit Specication .................................................... 124
Appendix B - Status Pages .......................................................... 126
Software Version 6.3 (12.0159) OCP1
WebPage Version wp8 1.0 (5984) ns PAL
3
Installation Guide
Introduction
1.03
The CamVu720 Series are high denition IP Cameras offering up to 2 megapixel image streams
in a choice of compression formats. With advanced features such as ICR, analytics support and
direct conguration from associated Video Servers, the CamVu720 Series contains a powerful suite
of enterprise-scale capabilities. The CamVu720 Series is also designed for Dedicated Micros next
generation of video surveillance - Closed IPTV.
HIGH DEFINITION STREAMING & RECORDING
The CamVu720 provides high denition image streams up to 2 megapixel, with a congurable resolution
of up to 1280x720 (16:9) and 1600x1200 (4:3). The powerful suite of streaming features ensure exibility
in remote viewing of the camera whilst on-board storage and supported transmission protocols such as
AoE provide a wealth of local and remote recording options..
ANALYTICSCAPABLE
As part of our growing range of AnalyticsCapable products, the CamVu720 Series is able to contain the
latest analytics solutions from Dedicated Micros including Object Left/Removed Detection Tripwire and
Counting Tripwire, all locally hosted on the camera.
NETVU CONNECTED
With NetVu Connected products users can seamlessly integrate Video Servers, Cameras & Domes,
Management Systems, mobile viewing devices and video walls together without the costly impact of
signicant integration time. A shared user interface helps minimise operator training whilst powerful
features such as Direct conguration of PTZ Cameras and Domes from connected DVRs helps reduce
installation time providing benets to both end user and installer/integrator.
The incredible exibility of Dedicated Micros NetVu Connected platform enables multi-environment
security installations to be achieved with ease. Integration of Fixed and Mobile DVRs and Video Servers
alongside products such as FireVu (for Video Smoke Detection) enable large scale solutions with several
application requirements to be designed and built with ease.
MULTIPLE, SIMULTANEOUS VIDEO STREAMS
Dedicated Micros’ unique Visual Signal Processor (ViSP) allows the CamVu720 Series to transmit multiple
simultaneous MPEG-4, H.264 and/ or JPEG images to any number of associated NetVu Connected
devices for image viewing. Each stream can be tailored to suit the viewer’s bandwidth requirements.
CLOSED IPTV
Dedicated Micros’ award winning Closed IPTV solution combines open standard IP protocols with patent
pending innovation to provide simple to install, safe and secure IP video solutions across new or existing
networks.
Automatically allocating IP addresses to IP cameras by physical port, a Closed IPTV system is completely
deterministic, creating rewalls and monitoring point-to-point IP connections so they cannot be hacked
or intercepted. Critical to the security of a Closed IPTV system is the unique implementation of Trusted
Endpoint technology; a secret signature, applied at lock down, enables endpoint devices such as IP
cameras to be secure, immediately triggering a security alert should any interference be detected.
This ground breaking solution provides a very simple and secure answer to IP video, meaning that no
prior knowledge of IP networking is required. Sophisticated and Dependable network security can be
achieved with a single click.
4CamVu 720
Features
■ High denition IP Camera - up to 2MP resolution
■ Available in static camera, internal mini-dome or Vandal Resistant Mini-dome options
■ Integrated Camera Recording and full enterprise video server within camera
■ Can form part of a Closed IPTV system
■ Transmission of multiple, simultaneous video streams in MPEG-4, H.264 and JPEG format
enables multiple users to view video streams at the settings they require
■ AnalyticsCapable - enables analytics solutions to be deployed on your CCTV system
■ Works with any DM Video Server that supports IP Streaming & Recording
■ MultiMode Recording - Dynamically-switchable resolution, record-rate & compression
(MPEG-4/H.264/JPEG) settings
■ Web server for remote conguration of camera features
■ Power over Ethernet (PoE) / 12-24Vdc & 24Vac power options
■ Local analogue test monitor output for use when positioning and adjusting the camera’s eld
of view and focus
■ Can be used externally in a compatible housing such as a DM/2010
■ TransCoding - High quality recording and simultaneous video transmission using MPEG4,
JPEG or H.264 for playback
■ Uses the latest Chipwrights ViSP to minimise power consumption and heat build up
Benets
• The camera supports recording to local SD card and network attached storage using ATA
over Ethernet
• The latest technology provides low light performance superb image quality and colour delity
in variable and high contrast lighting conditions.
• Operates seamlessly within a NetVu Connected network.
• Remote conguration removes the need for multiple revisits
• Images recorded locally on the camera in JPEG format can be viewed over low bandwidth
networks using MPEG-4
• BNC Connector allows local lens adjustment and display of the unit’s network settings on a
service monitor
Models
DM/CMVU720 1/4”VGA DVIP Colour 12-24V/PoE CamVu720
DM/CMVU7200/N 1/4”VGA DVIP Colour 12-24V/PoE NTSC CamVu720 NTSC
5
Installation Guide
1
2
2
3
4
3
1. Back focus mechanism locking screw (both sides)
2. Back focus adjustment (Top & bottom)
3. Mounting bush (Top & bottom)
4. AI lens connector (DC & video)
Components Supplied
Before installing unit, please verify that all items listed below have been supplied:
1 x CamVu Camera
1 x POE Injector Cable
1 x User Guide
1 x CD containing information for use with the camera
Note: A PSU is not supplied with this camera. A suitable 12Vdc 0.5A PSU is required if powering the
unit from its DC input connector - VS-PSU15W-EXT can be purchased separately from Dedicated
Micros.
If the camera utilises Power Over Ethernet, a separate PSU is not necessary (if power is
available via the Ethernet connection).
Alternatively if powering the unit over PoE using the supplied injector, a 48Vdc PSU that can
supply 15W is required - DM/PSU/48V can be purchased separately from Dedicated Micros.
6CamVu 720
Important Safeguards
Read Instructions
All the safety and operating instructions should be read before the unit is operated and adhered to during
operation. These instructions should be retained with the unit, and all warnings and cautions contained
should be heeded.
Power Sources
This unit should be operated only from the type of power source indicated on the manufacturer’s label.
Power Over Ethernet
This product supports POE and when connected to a suitable switch, will not require an external PSU to
drive the device (Bridge and end-span compatible).
Servicing and Repair
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous
voltage or other hazards.
Refer all servicing and repair to qualied service personnel.
Equipment
Use only attachments/accessories specied by the manufacturer.
Ventilation
Ensure unit is properly ventilated to protect from overheating.
Camera Care
In order to avoid damaging your camera, note the following points:
CAUTION
• The camera has threaded mounting points on the top and bottom of the case. Only use a
standard, photographic mounting bolt with a 1/4-20 UNC thread.
• Before tting the lens, make sure that its back will not touch the CMOS sensor or associated
components when screwed fully home.
• Do not touch the image surface of the sensor. If the sensor is accidentally touched, only
clean it using isopropanol.
• Do not expose the camera sensor to very bright light over a long period of time as this
may cause damage to the sensor. The camera and lens set-up must be correct to avoid
possible damage due to long term exposure to bright light. A lens with an automatic iris is
recommended under these conditions.
CE NOTICE (EUROPEAN UNION)
This section contains the regulatory declarations for the EU for the Unit Camera.
This product is marked with the CE symbol and indicates compliance with all applicable Directives. A
“Declaration of Conformity” is held at Dedicated Micros Ltd, 1200 Daresbury Park, Daresbury, Cheshire
WA4 4HS www.dedicatedmicros.com
7
Installation Guide
Hereby, Dedicated Micros LTD, declares that this Unit Camera is in compliance with the essential
requirements and other relevant provisions of Directive 95/5/EC.
Marking by the symbol CE indicates compliance of this Dedicated Micros product to the Electromagnetic
Compatibility Directive 89/336/EEC, and the Low Voltage Directive 73/23/EEC of the European Union.
Such marking is indicative that this system meets the following technical standards
• EN 61000-6-3 EMC Standard Residential, Commercial and Light Industry.
• EN 62000-3-3 Limitations of voltage changes, uctuations and icker in public low-voltage
supply systems for equipment with rated current up to 16A.
• EN 61000-3-2 Limits for harmonic current emissions for equipment with rated current up to
16A.
• EN 50130-4 Immunity requirements for components of re, intruder and social alarm
systems.
• EN 60950 Safety of IT and similar equipment.
• EN 55022 Class A. Radiated Emissions Standard, suitable for Commercial or Residential use
Further details about these applicable standards can be obtained from Dedicated Micros Ltd., 1200
Daresbury Park, Daresbury, Cheshire WA4 4HS
1.01002
RF Interference warning
This is a class A product. In a domestic environment this product may cause radio frequency interference
, in which case the user may be required to take adequate measures.
1.01003
Canadian EMC statement
This product is compliant with Class A ICES-003
Note: This Class A product meets the requirements of the Canadian Interference causing equipment
regulations. Cet appareil numerique de la Classe A, respect toutes les exigencies du reglement
sur le materiel brouilleur du Canada.
4.15
8CamVu 720
Installation
Rear Connections
The CamVu 720 features push t connectors which house connections for 12VDC power. There is also
a PoE capable RJ45 socket for connection to a suitable network point. The BNC video output connection
is used in conjunction with a local monitor to focus the camera during installation and can also be used to
display the camera’s current network settings.
Note: The BNC output only operates for 10 minutes after the camera is powered up.
DM/CMVU720
DM/CMVU720/N
1
2
3 4
5
6
1. Low voltage connector (12Vdc/24Vac 50/60Hz)
2. Power indicator LED
3. Power over Ethernet capable RJ45 socket
4. Composite video output BNC
5. MicroSD activity LED
6. MicroSD card slot
9
Installation Guide
Connections
Power Connections
CamVu720 cameras are available in PoE plus AC/DC low voltage types. The voltage required to operate
the camera is clearly marked on the rear panel of the camera. The power LED on the rear panel indicates
that power is connected.
Power over Ethernet
The camera can be powered from any suitable PoE injector conforming to IEEE 802.3-2008. End span
and bridging injectors supported.
Auto-Switching Low Voltage Power Supply
The camera is tted with an automatic selecting power supply operate between 12 VDC and 24 VAC.
Connections and polarity are indicated beside the connector on the rear panel. The power supply must be
a class 2 isolated type.
Network Connections
Connection to a 10/100 BaseT network is made via the RJ45 on the rear panel.
Video Connector
Connect a video coaxial cable terminated with a 75Ω BNC connector to the BNC socket marked VIDEO
OUT on the rear of the camera to align the camera.
Note: This video output is only active for 10 minutes after the unit is powered up.
10 CamVu 720
Lens Connections
Fixed and Manual iris lenses (for indoor use only) require no wiring connections.
Auto Iris Lens
Connect the auto iris lens to the four-pin connector located on the side of the camera. If the lens does
not have a DD plug tted then wire the lens to a suitable plug. Pin connections for the iris drive plug are
shown below.
PIN DIRECT DRIVE AUTO IRIS LENS
1 Control coil positive (+)
2 Control coil negative (-)
3 Drive coil negative (-)
4 Drive coil positive (+)
POE Injector Cable
The POE Injector cable is designed to enable the use of POE (Power over Ethernet) before a POE
capable switch has been installed. It is installed alongside a suitable 48Vdc PSU that can supply 15W is
required - DM/PSU/48V can be purchased separately from Dedicated Micros.
C
A
B
A Connection to DVR/NVR/Layer 3 Enhanced CCTV Switch
B Connection to suitable 48Vdc 15W PSU - (DM/PSU/48V)
C Ethernet cable connection to camera.
Important: 48V is supplied to connection C. There is no voltage at Connection A. Do NOT connect
an ethernet cable from connection C to the DVR/Layer 3 Enhanced CCTV Switch as this
could cause irreparable damage.
POE Injector Power Supply specication
Adaptor socket - 5.5mm diameter with a 2.1mm central circular pin
+48V goes to the centre pin of the power connector - 0V to the outside barrel
Indice
Altri manuali Dedicated Micros Telecamera IP
