Dell E1715S Istruzioni per l'installazione
E1715S 1
1
1. Disassembly Procedures:
Step Figure Remark
S1. Remove
the STAND
BASE ASS'Y.
Turnoffpower,
Unplugexternalcables
fromproduct
Note:
Put the monitor on a flat, soft
and clean surface.
Press the button on the red
circle then pull out the
stand follow the arrow,
stand-base assy will be
remove.
E1715S 2
S2. Remove
the REAR
COVER.
Use a Philips-head
screwdriver to remove 6
screws for unlocking
mechanisms.
(No.1~2 screw
size=M4x10;
Torque=12±2kgf.cm
No.5~6 screw
size=P3x4;
Torque=6±1kgf.cm)
Use Penknife to separate
the bezel and rear cove
follow the arrows in
sequence, then you can
take out rear cover.
1 2
3 4
5 6
E1715S 3
3
S3. Remove
the Cable.
Disconnect the key board
harness.
S4. Disconnect
the LED
HARNESS and
FFC CABLE.
Push
Push
E1715S 4
S5. Remove
the MAIN and
POWER
BOARD.
1. Turn over the main
frame.
2. Remove the Insulating
sheet.
Use a Philips-head
screwdriver to remove 4
screws for unlocking Main
board and Power board
(No.1~3 screw
size=M3x6;
Torque=6±1kgf.cm
No.4 screw
size=M4x6;
Torque=6±1kgf.cm）
Use a Philips-head
screwdriver to remove 1
screws for unlocking Main
board
（No.1 screw
size=M3x5;
Torque=6±1kgf.cm）
Use a hex screwdriver to
remove 2 screws for
unlocking mainboard
（No.2~3 Hex screw
Torque= 4.5±0.5kgf.cm）
1
2
3 4
1 2 3
E1715S 5
5
S6. Disconnect
the HARNESS.
S7. Remove
the MAIN
FRAME
S8. Remove
the PANEL
from Bezel
E1715S 6
S9. Remove
the KEY
BOARD.
Use a Philips-head
screwdriver to remove 4
screws for unlocking Key
board
(No.1~4 screw
size=M2x2.5;
Torque=0.7±0.2kgf.cm)
S10.Remove
capacitors
Remove electrolyte
capacitors (red mark)
from printed circuit
boards
Take out bulk cap. pin
solder with soldering
iron and absorber
1 2 3 4
E1715S 7
7
Lift the bulk cap. up and
away from the PCB
E1715S 8
2. Product material information
The following substances, preparations, or components should be disposed of or recovered
separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC.
Capacitors / condensers (containing
PCB/PCT)
No used
Mercury containing components No used
Batteries No used
Printed circuit boards (with a surface
greater than 10 square cm)
Product has printed circuit boards (with a
surface greater than 10 square cm)
Component contain toner, ink and liquids No used
Plastic containing BFR No used
Component and waste contain asbestos No used
CRT No used
Component contain CFC, HCFC, HFC
and HC
No used
Gas discharge lamps No used
LCD display > 100 cm2 Product has an LCD greater than 100 cm2
External electric cable Product has external cables
Component contain refractory ceramic
fibers
No used
Component contain radio-active
substances
No used
Electrolyte capacitors (height
> 25mm, diameter > 25mm)
Product has electrolyte capacitors
(height > 25mm, diameter > 25mm)
3. Tools Required
Listthetypeandsizeofthetoolsthatwouldtypicallycanbeusedtodisassembletheproducttoapoint
wherecomponentsandmaterialsrequiringselectivetreatmentcanberemoved.
ToolDescription:
‐Phillip head Screwdriver
‐HexScrewdriver
‐Penknife
‐Solderingironandabsorber
Altri manuali per E1715S
3
Indice
Altri manuali Dell Monitor
Dell
Dell P2722H Manuale utente
Dell
Dell UltraSharp 1703FP Istruzioni utente
Dell
Dell P2418HT Manuale utente
Dell
Dell D2720DS Manuale utente
Dell
Dell E2015HV Manuale utente
Dell
Dell ST2420L Manuale utente
Dell
Dell E550mm Manuale utente
Dell
Dell P3424WEB Manuale utente
Dell
Dell P2012H Manuale elenco delle parti
Dell
Dell S2719H Manuale utente
Dell
Dell UltraSharp 2208WFP Manuale utente
Dell
Dell S2740L Manuale utente
Dell
Dell W2306C Istruzioni utente
Dell
Dell E2723H Manuale utente
Dell
Dell U3023E Manuale utente
Dell
Dell E153FPT Manuale utente
Dell
Dell S2719DGF Manuale
Dell
Dell UltraSharp U2718Q Manuale utente
Dell
Dell IN1940MW Manuale utente
Dell
Dell S2418HN Manuale utente
