DELTA DORE DMF Tyxal+ Manuale utente

* Up to 10 years valid under the conditions of use specied in the installation instructions and the General Conditions of Sale

EN Wireless outdoor barrier motion detector

DMF Tyxal+

- 2 - - 3 -

Do not direct the lower detection zone towards

reecting surfaces (puddle, window, etc.).

Do not direct the detector towards moving objects

(leaves, bushes, ags, etc.).

N°1

N°6

N°4

N°3

N°2

N°5

N°7

Install the motion detector vertically, with

both high and low detection zones parallel

to the wall.

To ensure the device functions properly,

attach the motion detector to the wall.

Straps

Hook & Loop

Do not install close to a heat pump or heat

evacuation outlet (dryer, etc.).

3. Location

Install the motion detector vertically, with its

high detection zones parallel to the ground.

If the detector is installed at an angle,

detection reliability may be compromised.

An integrated spirit level enables optimal

installation.

1. Contents

Instructions

Important

Product

Informations

2. Presentation

TYXAL+ DMF is a passive infrared motion detector, designed to detect the infrared radiation

emitted by human bodies.

This motion detector aims to protect the outside of a building by detecting intrusions prior to

penetration into the premises. As soon as a presence is detected, it raises the alarm.

TYXAL+ DMF has an automatic system to protect it against being opened or ripped from its

mount.

It is also equipped with anti-masking detection, to prevent attempts to mask the lens.

• Paired with a control unit:

- alarm signal.

- pre-alarm signal: as soon as a person enters the protected zone, an audible and visual

signal (outdoor siren) warns you of the imminent alarm.

Read the entire guide before

starting to install the device.

Note

This product detects temperature di󰀨erences between moving and background targets

within the detection zone.

If the target remains motionless, the motion detector cannot detect it. This may a󰀨ect the

detector's maximum detection range.

N°1

N°6

N°4

N°3

N°2

N°5

N°7

For optimal operation, please comply with the following recommendations:

In the event of non-compliance, the product may present malfunctions or may not function

optimally.

Installation heights between 0.8 and 1.2 m: lateral

detection, max. range 12 m.

3. Location

- 4 - - 5 -

❶ Unlatch the top cover to open it.

❷ Press on the blue strips to separate the

detector from its base.

❸ Secure the base to the mount

using suitable screws and dowels.

The tamper alarm is triggered when

the base is broken and rests on the

wall.

4. Mounting 5. Activation

❶ Plug the battery cable into the card connector.

Set the (Tyxal+) alarm control panel to ‘pending

pairing’, then press the pairing button on the card.

Important: only the blue/green wires must be

connected to the wireless card (and not the grey/

yellow wires).

❷ Reposition the sensor/electronic

card on the base

Attention: lock the detector part

by pushing the blue strips until you

hear a "click".

Only the blue parts are action-

able.

❸Close the cover

❹ A 3-minute detection test launches

automatically.

Check that you are detected by moving into the

detection zone.

❺ With each detection, the LED ashes for 5

seconds.

Test mode automatically stops after 3 minutes

and the system returns to "Normal" mode.

- 6 - - 7 -

6. Detector range seings for each side

Fixed to the wall

O󰀨set from the wall

Depending on your installation, the detection beams can be o󰀨set from the wall (3 degrees).

To do this, slide the compartment to reveal the "AWAY WALL" message (see image below).

The detection distance can be congured separately for the right and the left side.

7. Detection sensitivity seings

Switch settings

The switches must be positioned towards the

bottom during normal operation.

Switch 7: anti-masking function

• OFF position: Function inactive

• ON position: Function active

The masking of the lens is indicated by an

Auto-Protection fault.

Detection sensitivity settings

The sensitivity can be independently adjusted

for each side, (L) left and (r) right, to 3

positions:

• L (low),

• M (medium),

• H (high),

The chosen position will depend on

environmental conditions.

<We recommend that you set the sensitivity

level

to H (high):

• When the detection beams were tilted

horizontally.

• When higher sensitivity is required

towards the end of the detection zone (12

m).

to L (low):

• When the device is installed in a

mediocre location (bad conditions).

• When there is a high risk of faulty

detection.

High sensitivity:

The detection sensitivity can be increased

by toggling switches 4 (left side) and 5 (right

side) to ON.

• Pairing with an alarm system

• Pre-alarm

• Selection of triggering method

• Test

Read system installation

guide

8. Operation with an alarm system

Left side

Switch 4

High sensitivity

Right side,

switch 5

- 8 - - 9 -

9. Baery replacement

The LED ashes continuously, the battery is dead.

IMPORTANT: Before opening the unit, the alarm control unit must be in Maintenance mode

(refer to system installation guide).

❶ Unlatch the top cover to open it. ❷ Press on the blue strips to separate the

detector from its base.

Problem Probable cause Sustainable

The LED ashes

continuously. Incorrect power supply. Change the battery.

Triggered

detection without any

objects moving

The motion detector was not installed

perpendicular to the ground.

Install the motion detector

correctly.

A reecting object is located within

the detection zone.

Eliminate all reecting surfaces from

the detection zone.

The lower beam is longer than

expected.

Check and readjust the detection

beam.

The lower detection beam is

exposed to direct sun rays or to car

headlights.

Readjust the detection beam

so it is no longer exposed to direct

light sources.

Presence of a heat source (heating

device, etc.) in the detection zone

that may cause the temperature to

change.

Readjust the detection beam or

eliminate the heat source in the

detection zone.

An object is moving (washing hung

up on a line, plants, etc.).

Readjust the detection beam or

remove moving objects.

In the event of heavy rain, water

may pour through the detection zone

(overowing gutter, roof/terrace/

balcony drainage, etc.)

Readjust the detection beam

so it is no longer directly exposed to

the owing water.

The sensitivity setting is too high.

Ability to reduce the sensitivity:

- select L rather than M or H

- check that switches 4 and 5 are set

to OFF.

Occasionally no

detection.

Occasionally no detection. Readjust the detection beam

correctly.

Sensitivity is set to L (low). Readjust the sensitivity level to M

(medium) or H (high).

10. Troubleshooting

www.deltadore.com

Caractéristiques techniques / Technical characteristics / Technische Daten

Caraeristiche tecniche / Características técnicas / Technische kenmerken

2xLS 14500 - 3.6 V / 5.2 Ah - Lithium

Consumption stand-by : 16 µA

Consumption : 8 mA max / 3,6 Vcc

[868 - 868.6] MHz and

[868.7 - 869.2] MHz

100 m -> 300m

Maximum power radio < 10 mW,

receiver category: 2

-10°C / +70°C

-30°C / +60°C

IP IP 55

95%

92,8 x 199,7 x 98,7 mm

550 gr.

Important product

information (❸)

Indice

Altri manuali DELTA DORE Sensore di sicurezza

DELTA DORE

DELTA DORE Tybox RF6700FP Manuale utente

DELTA DORE

DELTA DORE DME 90 Tyxal+ Manuale utente

DELTA DORE

DELTA DORE TYXAL DU Manuale utente

DELTA DORE

DELTA DORE TYXAL DOS Manuale utente

DELTA DORE

DELTA DORE DMB TYXAL + Manuale utente

DELTA DORE

DELTA DORE Tyxal+ DME 180 Manuale utente

DELTA DORE

DELTA DORE DTX Manuale utente

DELTA DORE

DELTA DORE Tywatt 5400 Manuale utente

DELTA DORE

DELTA DORE DOI PVC TYXAL + Manuale utente

DELTA DORE

DELTA DORE DMB TYXAL+ Manuale utente

DELTA DORE

DELTA DORE TYXAL DOI PVC Manuale utente

DELTA DORE

DELTA DORE TYXAL DOS Manuale utente

DELTA DORE

DELTA DORE DMBD TYXAL+ Manuale utente

DELTA DORE

DELTA DORE DMB TYXAL+ Manuale utente

DELTA DORE

DELTA DORE TYXAL Manuale utente

DELTA DORE

DELTA DORE DU TYXAL + Manuale utente

DELTA DORE

DELTA DORE DMB TYXAL+ Manuale utente

DELTA DORE

DELTA DORE DMBV TYXAL+ Manuale utente

DELTA DORE

DELTA DORE DVR TYXAL+ Manuale utente

DELTA DORE

DELTA DORE DCS TYXAL + Manuale utente

DELTA DORE

DELTA DORE DOS TYXAL + Manuale utente

DELTA DORE

DELTA DORE TYXAL DCP Manuale utente

DELTA DORE

DELTA DORE DMBE TYXAL+ Manuale utente

DELTA DORE

DELTA DORE TYXAL DOI PVC Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente