DELTA DORE MINOR 11 Manuale utente

MINOR 11

Installation and User Guide

Electronic thermostat for underfloor

heating or radiant ceiling heating

DELTA DORE - Bonnemain

35270 COMBOURG - FRANCE

E-mail : deltadore@deltadore.com

Device compliant with the requirements of directives:

2004/108/CEE (Electromagnetic compatibility)

and 2006/95/CEE (Low voltage safety)

Because of changes in standards and equipment, the characteristics

given in the text and the illustrations in this document are not binding

unless confirmed by Delta Dore.

*2702007_rev.1*

- 2 -

1- ContentsWarnings

• Carefully read these instructions prior to

installation.

• The unit must be installed in compliance with

currently applicable standards.

• Always switch off the mains before installing or

servicing the unit.

• Do not attempt to repair the unit yourself; an

after-sales service is available.

• The diagrams provided are simplified for

greater clarity.The protective units and other

accessories required by the standards are not

illustrated.

Standard UTE NF C15-100 and good practice

must be complied with. Connected or nearby

equipment must not generate excessive

interference (directive 2004/108/EEC).

- 3 -

1 - Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 - Presentation . . . . . . . . . . . . . . . . . . . . . . . 4

2.1 Pilot wire principle (GIFAM standard) . . . 5

3 - Location . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4 - Mounting / Connection . . . . . . . . . . . . . . . . 7

5 - Connections . . . . . . . . . . . . . . . . . . . . . . . . 8

6 - Switching on the unit for the first time . . . . 9

7 - Installer commissioning . . . . . . . . . . . . . . 10

7.1 Choosing the temperature displayed . . . 10

7.2 Choosing the control sensor . . . . . . . . . 10

7.3 Correcting the temperature measurement 11

7.4 Locking user access . . . . . . . . . . . . . . . 12

7.5 Choosing the installation type . . . . . . . 13

7.6 Gradual heating . . . . . . . . . . . . . . . . . . 13

7.7 Power to be switched . . . . . . . . . . . . . . 14

7.8 Exiting the installer mode . . . . . . . . . . 14

8 - Operation . . . . . . . . . . . . . . . . . . . . . . . . 15

8.1 Choosing the operating mode . . . . . . . . 15

8.2 Set-point temperature setting . . . . . . . 15

9 - Technical characteristics . . . . . . . . . . . . . . 17

10 - Maintenance . . . . . . . . . . . . . . . . . . . . . 18

- 5 -- 4 -

Relay status Current mode

Adjustment buttons

Selection of

the operating mode

or configuration

(installer)

Set-point

temperature or

temperature

measured per

MINOR 11 Auto

Heating

demand

mode

Off

Comfort

Economy

Frost

Protection

15 mm 33 mm 80 mm

80 mm

Part fitting into the

flush-mounted box

2.1The pilot wire principale (CALYBOX standard)

The pilot wire principle enables the required

operating mode to be selected from a programmer

(CALYBOX range, Driver range, etc.).

The MINOR 11 thermostat thus controls the

corresponding temperature.

Order sent by

the programmer Corresponding temperature

controlled by the thermostat

Comfort

Comfort- 1°C

Comfort setting (5°C to +30°C)

Comfort - 1°C setting

Comfort- 2°C Comfort - 2°C setting

Economy Economy setting (5°C to +30°C)

Frost Protection Frost protection Frost protection can

be set from 5°C to 15°C (7°C by default)

Off Heating switched off

2- Presentation • Suitable for underfloor heating or radiant ceiling

heating

• Permanent regulation (proportional integral)

• Simple control system (pilot wire principle)

• Up to 6 operating modes (GIFAM standard)

- 6 - - 7 -

3- Location

The MINOR 11 thermostat is mounted flush-moun-

ted in a flush-mounted box. It should be placed in

a room whose temperature represents the mean

temperature, with a recommended height of 1.5 m

and it should be away from any heat sources

(fireworks, sunlight) and from air flows (window,

door, etc.).

To avoid unwanted air movements that would

distort the sensor measurement, the wire entry

into the flush-mounted box must be plugged

(mastic, glass wool, etc.).

IMPORTANT: Do not install the MINOR 11 on a

wall in contact with the outside or in an unheated

room (e.g. garage, etc.).

Approx.

height

1.50 m

Min. 40 cm

4- Mounting / Connection

To open the casing, slide

the moving tabs using a

screwdriver and remove the

front panel from the base to

be flush mounted.

Switch off the power

supply to the system

before carrying out any

operation

MODE

Moving

tabs "Click"

Before securing the base to the

flush-mounted box, pass the wires

through the hole in the base.

When the base is secured, connect

the wires to the terminal (strip the

wires: approx. 6 mm). Fit back the cover and

lock it by pushing the

moving tabs

downward.

Switch on the

installation.

- 9 -- 8 -

5- Connections

NPilot

Wire 67

Underfloor

sensor

Pilot

Wire Underfloor

sensor

MINOR 11Load

10A - 230V

Maximum load 2.300 W

load

Pilot wire from

programmer

Pilot wire from

programmer

The relay capacity depends on

the power to be switched

Max. power: 2,300 W, otherwise relay

MINOR 11Load

10A - 230V

The reference number of the underfloor sensor to

use is 6300037.

6- Switching on the unit for the first time

When the MINOR 11 is first switched on, it starts up

the “gradual heating” mode designed for new

underfloor heating systems for which a gradual

heating is recommended (over a period of 20 days).

In this mode, the heating percentage is limited to 8%

on the 1st day, 12% the 2nd day... up to 100% on the

20th day.

The display shown the number of

remaining days and .

The symbol flashes.

- The program can be stopped at

any moment by pressing .

- pressing the button displays the current

program P1.

After the 20-day period, MINOR 11 exits the gradual

heating mode and returns to the Off mode.

The heating can always be started again in gradual

heating mode.(see Installer commissioning).

- The percentage shown above is calculated in

relation to the regulation time base,

- The gradual heating mode depends on the

set-point temperature.

- 11 -

7.3 Correcting the temperature measurement

(CF05)

If you notice a difference between the temperature

recorded (thermometer) and the temperature

measured by the unit, this menus allows you to

correct the difference (+/-5°C in increments of 0.1°C).

E.g. The temperature displayed is 19°C and the

temperature recorded is 20°C, so set

+1°C.

Make the selection by or ,

Confirm by pressing and

releasing .

Go on to the next menu.

You must wait at least 24 hours until the effect of

the correction can be observed in the room.

- 10 -

7- Installer commissioning

To enter this mode, press the button

for 10 seconds until CF01 is

displayed.

7.1 Choosing the temperature displayed (CF01)

:Temperature of the room measured by

MINOR 11

: Current set-point temperature (default mode)

Select by pressing the or buttons and ,

confirm by pressing and releasing . Go on to

the next menu.

7.2 Choosing the control sensor (CF02)

: Sensor within the casing (by

default)

: Underfloor sensor (optional)

Select by pressing the or buttons

and , confirm by pressing and releasing

Passage au menu suivant.

7.6 Gradual heating (CF09)

CF09 is displayed.

: Start-up program 1 (dry floor).

: Start-up program disabled

Select by pressing the buttons or , and

confirm by pressing and releasing .

- 13 -

7.5 Choosing the installation type (CF07)

This menu is used to determine the type of

installation so that the most suitable regulation

settings are used.

: Underfloor heating application - P.I. type

regulation (default display)

: Ceiling heating application - P.I.type regulation

Select by pressing the buttons or , and

confirm by pressing and releasing .

Go on to the next menu.

Paramètre disponible si choix sonde interne §7.2

- 12 -

7.4 Locking user access (CF06)

Important: Before activating the user locking feature,

select the required operating mode (

: Les touches sont verrouillées.

Only the set-point configured before

the locking operation can be changed

to +/- 3°C (except for the and modes).

: Active buttons (default display).

Make the selection by the buttons or ,

Confirm by pressing and releasing .

Go on to the next menu.

- 15 -

8.2 Set-point temperature setting

8.2.1 Set-point setting for the sensor within the

casing (selection of sensor type made §7.2)

Select the mode to set ( , or ) by using

the button .

Use or , to make your choice (5°C to

+30°C or 5°C to 15°C for the ).

In Comfort mode, MINOR 11 will regulate

according to the set-point configured.

8- Operation

8.1 Choosing the operating mode

Select the operating mode by pressing and

releasing the button repeatedly :

AUTO MINOR 11 follows the mode

requested by the programmer.

Comfort MINOR 11 regulates according to

the Comfort set-point configured.

Economy MINOR 11 regulates according to

the Economy set-point configured.

Frost

Protection MINOR 11 regulates according to the

Frost protection set-point configured.

OFF The heating is shut down

- 14 -

7.8 Exiting the installer mode

You can exit the installer mode by

pressing the button after the

last menu (CF09 - § 7.6 or CF10

- § 7.7) or automatically after

2 minutes without pressing any

button.

7.7 Power to be switched (CF10)

This parameter is only displayed if the

Underfloor heating mode (CF07 - § 7.5)

and the internal sensor (CF02 - § 7.2)

are selected.

: Up to 1,000 W (direct control)

: From 1,000 W to 2,300 W (direct control, by

default)

: Greater than 2,300 W (contact switch control)

Press the button several times for rapid access to

a specific menu

- 17 -

10- Technical characteristics

Electrical

• 230 V, 50 Hz power supply, ±10%

• Class II insulation

• Power consumption: 0.5 VA

• Power supplied operating contact output, 10 A,

230 V

• Automatic action: type 1.C

• 1 pilot wire input from programmer

Specific operation

• 6 Operating modes:

- Comfort and economy (adjustable from 5°C to

30°C)

- Comfort -1°C and Comfort -2°C

- Frost protection adjustable from 5°C to 15°C

(except for underfloor sensor applications)

- Off

• P.I. type regulation (proportional integral),

20 minute time base either in relation to the

thermostat sensor, or in relation to an underfloor

sensor.

• eu.bac certificate no. 020713

Application: Electric Underfloor Heating

CA: 0.7

- 16 -

8.2.2 Underfloor sensor set-point setting

(selection of sensor type made in § 7.2)

Select the mode to set ( or , Frost protection)

by the button .

Use or , to make your choice (setting of

5 to 40°C for Comfort or Economy, and 5 to 30°C for

Frost protection).

Note: Note: Setting the floor temperature to 26°C

corresponds to a room temperature of about 20°C.

A floor temperature of 23°C corresponds to a room

temperature of about 18°C.

The values specified are theoretical values.

The settings must be readjusted after a few days

use.

When a choice is made to display the current

temperature (default mode, § 7.1), the first time the

button or is pressed will display room

temperature, pressing it a second time allows you

to adjust the set-point.

- 18 -

Nothing appears on the

screen No power supply

Check the power supply

The indication

flashes •The “gradual heating”

mode is enabled

See chapter 7

You cannot set a

set-point temperature The buttons are locked

See the “installer mode”

chapter or

AUTO mode is enabled

(set-points cannot be changed)

Problem Diagnosis / Solutions

11- Maintenance

Mechanical

• Dimensions: LxHxD = 80 x 80 x 48 mm

• IP 30

• Wall-mounted on flush-mounted box

• Installation in an environment with normal pollution

levels

Technical

• Storage temperature: -10°C to +70°C

• Operating temperature: 0°C to +40°C.

Altri manuali per MINOR 11

Indice

Altri manuali DELTA DORE Termostato

DELTA DORE

DELTA DORE 6050675 Manuale utente

DELTA DORE

DELTA DORE PACK TYBOX 5000 Manuale utente

DELTA DORE

DELTA DORE TYBOX 117 Manuale utente

DELTA DORE

DELTA DORE CALYBOX 110 Manuale utente

DELTA DORE

DELTA DORE TYBOX 21 Manuale utente

DELTA DORE

DELTA DORE TYBOX 147 Manuale utente

DELTA DORE

DELTA DORE Tybox 5701FP Manuale utente

DELTA DORE

DELTA DORE TYBOX 5100 Manuale utente

DELTA DORE

DELTA DORE TYBOX 5101 Manuale utente

DELTA DORE

DELTA DORE Tybox 1137 Manuale utente

DELTA DORE

DELTA DORE TYBOX 610 Manuale utente

DELTA DORE

DELTA DORE TYBOX PAC Manuale utente

DELTA DORE

DELTA DORE TYBOX 5101 Manuale utente

DELTA DORE

DELTA DORE TYBOX 51 Manuale utente

DELTA DORE

DELTA DORE TYBOX 817- 827 W RF Manuale utente

DELTA DORE

DELTA DORE TYBOX 117 Manuale utente

DELTA DORE

DELTA DORE DELTA 8000 MASTER Manuale utente

DELTA DORE

DELTA DORE Tybox 1117 Manuale utente

DELTA DORE

DELTA DORE Tybox 5300 Manuale utente

DELTA DORE

DELTA DORE TYBOX 610 Manuale utente

DELTA DORE

DELTA DORE PACK TYBOX 5000 Manuale utente

DELTA DORE

DELTA DORE RADIO TYBOX Manuale utente

DELTA DORE

DELTA DORE TYBOX 817 W RF Manuale utente

DELTA DORE

DELTA DORE TYBOX 117 Manuale utente

Manuali Termostato popolari di altre marche

EWELLY

EWELLY EW-181 Manuale utente

Prolon

Prolon T1100 Istruzioni per l'installazione

Computherm

Computherm Q20 Manuale utente

Heatmiser

Heatmiser neoStat Manuale utente

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuale utente

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuale utente

Saswell

Saswell SAS920XWHB-7-S-RF Guida

Aircalo

Aircalo TFP1-ET85P2 Manuale utente

Honeywell

Honeywell CM721 Manuale utente

Carrier

Carrier DEBONAIR 33CS Manuale utente

Lennox

Lennox iHarmony Zone Thermostat Istruzioni per il montaggio

Gemtech

Gemtech GT7000 Manuale di istruzioni

Rollei

Rollei Smartes 45000 Manuale utente

Sinope

Sinope TH1300RF Manuale utente

Honeywell

Honeywell RLV4305 Manuale utente

Honeywell

Honeywell Prestige 2.0 THX9421 Manuale utente

NuTone

NuTone NTBZ48 Istruzioni operative originali

Stelpro

Stelpro MAESTRO ASMT402AD Manuale utente