Delta Electronics Agema Series Manuale utente
Delta Networking – Agema Family
AGC7646V1 Aggregation Switch
Installation Guide
agema.deltaww.com
ii
AGC7646V1 Aggregation Switch
Copyright
All specications and gures are subject to change without prior notice. Actual products may look
different from the photos.
All trademarks and logos mentioned in this guide are the properties of their respective holders.
Copyright © Delta Electronics, Inc. All rights reserved.
Regulatory and Safety Information
This product has been tested in accordance to, and complies with the following safety standards and
electromagnetic compatibility (EMC) inspection standards.
Emissions
Applicable standard
• AS/NZS CISPR 32: Class A
• ICES-003: Class A
• EN55032: Class A
• VCCI Class A
• FCC CFR 47 Part 15, Subpart B Class A
Safety
Applicable standard
• EN 62368-1, Second Edition
• UL 62368-1, Second Edition
• CAN/CSA C22.2 No. 62368-1, Second Edition
• IEC 62368-1, Second Edition Including All National
Immunity
Applicable standard
• EN 55024
• EN 61000-3-2: Harmonic Current Emissions
• EN 61000-3-3: Voltage Fluctuations and Flicker
• EN 61000-4-2: ESD
• EN 61000-4-3: Radiated Immunity
• EN 61000-4-4: EFT
• EN 61000-4-5: Surge
• EN 61000-4-6: Low Frequency Conducted Immunity
• EN61000-4-8: Power Frequency magnetic eld
• EN61000-4-11: Voltage dips and interruption
EU RoHS Compliant
Applicable standard All AG-Series components are EU RoHS compliant
iii
Important!
This product is intended for installation only in the RESTRICTED ACCESS AREA ACCESSIBLE only
to SKILLED PERSONS and INSTRUCTED PERSONS with the proper authorization.
•Access is through the use of a lock or tool and key, or other means of security, and is controlled by
the authority responsible for the location.
•Access can only be gained by service persons or by users who have been instructed about the
reasons for the restrictions applied to the location and about any precautions that shall be taken.
•Never open the equipment and/or switch the plug-in power supplies and fan tray modules. For
safety reasons, the equipment should be opened and maintenance only by qualied service
personnel / SKILL PERSONS.
This product is intended for installation in Information Technology Equipment Rooms (Data Center):
“Suitable for installation in Information Technology Rooms in accordance with Article 645 of the
National Electrical Code and NFPA 75.”
Important!
Ce produit est conçu pour une installation dans un ENDROIT À ACCÈS RESTREINT, ACCESSIBLE
uniquement par des PERSONNES COMPÉTENTES et QUALIFIÉES possédant les autorisations
appropriées.
•L’accès est limité par un cadenas, un outil, une clé ou par un autre moyen et est contrôlé par
l’autorité responsable des lieux.
•L’accès n’est permis que pour le personnel de service ou les utilisateurs qui ont été informés sur
les raisons de la restriction imposée sur l’emplacement et sur les précautions éventuelles qui
doivent être entreprises.
•N’ouvrez jamais l’équipement et ne mettez pas les modules du bloc d’alimentation et du plateau
de ventilation sous tension. Pour des raisons de sécurité, l’ouverture ou l’entretien de l’équipement
doit être effectué par le personnel de service ou des PERSONNES COMPÉTENTES.
Ce produit est conçu pour être installé dans les salles de la technologie de l’information (centre des
données) :
« Il convient à l’installation dans des salles de la technologie de l’information conformément à l’article
645 du National Electrical Code et de NFPA 75 ».
Warning: Fiber Optic Port Safety
When using a ber optic port, never look at the transmit laser while it is powered
on. Also, never look directly at the ber TX port and ber cable ends when they are
powered on.
Avertissement : Consignes de sécurité concernant le port de
fibre optique
Ne regardez jamais le faisceau de laser émis activé lorsque vous utilisez un port de
bre optique. Également, ne regardez jamais le port de bre TX et les extrémités du
câble du bre directement lorsqu’ils sont activés.
iv
AGC7646V1 Aggregation Switch
CAUTION
Lithium Battery Caution
Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type.
Dispose batteries according to manufacturer’s instructions.
Disposal of a BATTERY into re or a hot oven, or mechanically crushing or cutting of a BATTERY, that
can result in an EXPLOSION.
Leaving a BATTERY in an extremely high temperature surrounding environment that can result in an
EXPLOSION or the leakage of ammable liquid or gas.
A BATTERY subjected to extremely low air pressure that may result in an EXPLOSION or the leakage
of ammable liquid or gas.
Grounding Caution
This equipment must be grounded and the power cord for product should be connected to a socket-
outlet with earthing connection. Note that the grounding screw of chassis should be connected to rack
instead of protective earthing conductor.
If this equipment is installed in the restricted-access location, it should have a separate protective
earthing terminal on the chassis which must be permanently connected to earth ground to adequately
ground the chassis and protect the operator from electrical hazards.
This equipment might provide the hazardous voltage and must be connected by qualied service or
technical person, or be instructed and supervised by qualied service or technical person.
Multiple Power Sources Caution
This symbol indicates the presence of hazardous energy circuits or electric shock hazards. Refer all
servicing to qualied personnel.
WARNING: Do not open the enclosure to reduce the risk of injury from electric shock hazards. Refer
all maintenance, upgrades and service servicing to qualied personnel.
Caution: The power control button on the device and the power switch on the power supply do not turn
off the electrical current supplied to the device. The device also might have more than one power cord.
To remove all electrical current from the device, ensure that all power cords are disconnected from the
power source.
v
MISE EN GARDE
Mise en garde concernant la pile au lithium
Risque d’explosion si la pile est remplacée incorrectement. Remplacez-la avec une pile semblable ou
de même type uniquement. Éliminez les piles selon les directives du fabricant.
L’élimination de la PILE dans un feu, un four chaud ou un broyeur mécanique peut provoquer une
EXPLOSION.
L’exposition de la PILE à une température ambiante extrêmement élevée peut provoquer une
EXPLOSION ou la fuite d’un liquide ou d’un gaz inammable.
L’exposition de la PILE à une pression atmosphérique extrêmement basse peut provoquer une
EXPLOSION ou la fuite d’un liquide ou d’un gaz inammable.
Mise en garde concernant la mise en terre
Cet équipement doit être mis à terre et le cordon d’alimentation du produit doit être branché à une
prise mise à terre. Notez que la vis de mise à la terre du châssis doit être xée sur le bâti plutôt que
sur le conducteur de protection.
Si cet équipement est installé dans un emplacement à accès restreint, l’équipement doit être doté
d’une borne de mise à terre distincte sur le châssis qui doit être branchée adéquatement et en
permanence an de le mettre à terre et protéger les utilisateurs contre les dangers électriques.
Cet équipement peut générer du courant dangereux et doit être branché par du personnel technique
ou de service qualié ou par des personnes informées et supervisées par du personnel technique ou
de service qualié.
Sources multiples d’alimentation
Ce symbole indique la présence de circuits dangereux ou des risques de décharges électriques.
Conez la réparation à du personnel qualié.
AVERTISSEMENT : N’ouvrez pas le boîtier an de réduire les risques de blessures causées par des
décharges électriques. Conez la réparation, les mises à jour et l’entretien à du personnel qualié.
Mise en garde : Le bouton d’alimentation et le commutateur de l’appareil ne coupent pas le courant
électrique qui alimente l’appareil. L’appareil peut également être branché à plusieurs cordons
d’alimentation. An de couper complètement le courant électrique de l’appareil, assurez-vous de
débrancher tous les cordons d’alimentation de la source d’alimentation.
vi
AGC7646V1 Aggregation Switch
Table of Contents
Chapter 1: Introduction -------------------------------------------------------------------1
1.1 Overview ------------------------------------------------------------------------------------ 1
1.2 Package Content ------------------------------------------------------------------------- 1
1.3 Features------------------------------------------------------------------------------------- 2
Chapter 2: Appearance and Mechanism --------------------------------------------3
2.1 Product Overview ------------------------------------------------------------------------- 3
2.2 LED Identication ------------------------------------------------------------------------- 4
2.3 System Requirements ------------------------------------------------------------------- 7
2.4 Data Center Deployment --------------------------------------------------------------- 8
2.5 Power Supply Modules ------------------------------------------------------------------ 9
2.6 Fan Tray Module -------------------------------------------------------------------------10
Chapter 3: Installation ------------------------------------------------------------------- 11
3.1 Mounting -----------------------------------------------------------------------------------11
3.2 Installing an Optional Transceiver and Cable ------------------------------------14
3.3 Connecting to the Console Port ------------------------------------------------------15
3.4 Connecting to a Power Source -------------------------------------------------------16
Chapter 4: Making the Network Connections ----------------------------------- 19
4.1 Twisted-pair Connections --------------------------------------------------------------19
4.2 Fiber Optic Connections ---------------------------------------------------------------20
4.3 Ethernet Cabling -------------------------------------------------------------------------21
Appendix 1 : Technical Specifications--------------------------------------------- 22
Appendix 2 : Warranty------------------------------------------------------------------- 23
Limited and Support Warranty -------------------------------------------------------------23
Technical Support -----------------------------------------------------------------------------23
1
Chapter 1: Introduction
1.1 Overview
AGC7646V1 is a ToR/Leaf and EoR switch with deep buffers for data center deployment
or as mobile access/aggregation switching and edge routing in service provider network.
AGC7646V1 is not only offering 100GbE uplink ports but also supporting virtualization
features. AGC7646V1 is SDN capable, compatible with choices of third party NOS and as
well as ONIE, openow for today’s open network ecosystem. It also provides comprehensive
capability on layer 2 and layer 3 features, including SNMP, Spanning Tree, VLAN, QinQ,
Trunk, QoS, RIP, OSPF, IGMP, DVMRP, PIM-DM, PIM-SM, Access Control, etc. This product
which aims for Data Center and Carrier Networks also supports advance features such as
MPLS, TRILL, PFC, VEPA, QCN, VxLAN and NVGRE to meet Data Center high performance
and virtualization requirement.
1.2 Package Content
After unpacking this switch, check the contents to be sure you have received all the
components. Then, before beginning the installation, be sure you have all other necessary
installation equipment.
•AGC7646V1
•Rack-mounting kits
•Installation guide
If any item is missing or damaged, contact the vendor immediately, see “Technical Support”.
2
AGC7646V1 Aggregation Switch
1.3 Features
The following lists the key main features of AGC7646V1 switch:
•46 x 10GbE SFP+ and 6 x 100GbE QSFP28 ports, support splitter cable
•1 x RJ45 OOB management port
•1 x RJ45 Console port
•1 x USB port
•System / Fan / Power status LED indication and per port LEDs
•On board high performance CPU system with large memory
•Hot-swappable PSUs and 1+1 redundancy support
•Hot-swappable FANs and 3+1 redundancy support
•Standard 1RU chassis high
•800Gbps interface bandwidth
•Low pin-to-pin latency: Cut-Through and Store & Forward Mode
•4GB GDDR5 of packet buffer memory
•External TCAM for extending classication database
•Support Jumbo Frame up to 9Kbyte
•Supports port speeds of 10G, 25G, 40G, 100G
3
Chapter 2: Appearance and Mechanism
2.1 Product Overview
2.1.1 Front View
Management port x 1
Console port x 1
QSFP28 port x 6
SFP+ port x 46
(Figure 2-1: Front View)
2.1.2 Rear View
PSU x 1
4 Fan tray slots
Secondary PSU
slot x 1 (optional)
(Figure 2-2: Rear View)
NOTE:
The switch supports up to two PSUs. However, it might be shipped with one power supply
pre-installed in the rear panel of the switch. You may purchase an additional PSU for
redundancy.
4
AGC7646V1 Aggregation Switch
2.2 LED Identification
This section provides an overview of the front and rear LEDs.
2.2.1 Front LEDs
Upper SFP+ Port LED
Lower SFP+ Port LED
Upper QSFP28 Port LED
Lower QSFP28 Port LED
Power LED
System LED
Fan LED
(Figure 2-3: Front LED Identification)
LED Description
System LED
• Solid Green – Normal operation
• Blinking Green – Booting progress or System in diagnostic mode
• Solid Amber – System failure
• Off – No power
Power LED
• Solid Green – Power supply units are supplied to the switch & operating normally
• Solid Amber – Power supply unit failure
• Off – Power is disconnected
Fan LED • Solid Green – All fans are operating normally
• Solid Amber – One or more fans failure
10G SFP+
slots
LED (Solid Lighting –Linkup; Blinking –Activity)
• Solid Green – A valid 10G link
• Solid Amber – A valid 1G link
• Blinking –Packet transmission or reception in progress
• Off – No link
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Delta Electronics Interruttore
Delta Electronics
Delta Electronics MSW 51 Manuale utente
Delta Electronics
Delta Electronics NovoConnect B360 Manuale utente
Delta Electronics
Delta Electronics STS30002SR10135 Manuale utente
Delta Electronics
Delta Electronics SK1027 Manuale utente
Delta Electronics
Delta Electronics SSW 230 V - 20 kVA Istruzioni per l'installazione
