Delta Regis DRFF-530R Guida utente
DRFF-530R
Screw Feeder
Operation and Setup Manual
CAUTION — Please read, understand, and follow all operating and
safety instructions in this manual before using a DRFF screw feeder.
If you have any questions or concerns, please contact us at:
Delta Regis Tools, Inc. Ph +1-772-465-4302
7370 Commercial Circle Fx +1-772-465-4368
Fort Pierce, FL USA 34951 Email: sales@deltaregis.com
Website: www.deltaregis.com
Delta Regis_DRFF-530R_M_R0.0
Copyright © 2022 Delta Regis Tools Inc
DRFF-530R Screw Feeder
Operation and Setup Manual
www.deltaregis.com 2
Warning — Failure to understand and follow proper installation guidelines, safety requirements,
and operating instructions may result in malfunction, component damage, property damage,
shock hazard, re hazard, injury or death.
• Please read and understand the operation manual and follow all safety and operation
instructions.
• Use these products in a suitable dry, indoor location. Do not use the screw feeder in damp,
wet, or high temperature environments. Do not use in the presence of ammable liquids or
gases.
• Use only a properly grounded electrical outlet of the correct supply voltage to power the
screw feeder.
• Ensure that the supply outlet is overload protected and of sucient amperage capacity.
• Use only the supplied AC adapter and power cord for the screw feeder and outlet. Hold the
plug of the power cord when connecting or disconnecting. Do not pull on the cable.
• Do not expose the cable, AC adapter or screw feeder to oil, chemicals, or heat. Ensure that
the cable is routed and used in such a manner as to not be subject to sharp objects that
may abrade or cut the cable.
• Locate the screw feeder in a suitable, safe location on a steady, level surface.
• Do not place in a high location where there may be a risk of it falling.
• Do not tilt the screw feeder.
• Do not raise the front or rear of the screw feeder.
• The screw feeder rail must be kept free from oil, grease, dust or any other contaminates.
• Do not place you hand or any foreign objects into the screw hopper when the unit is
running.
• In the event that the screw feeder is overloaded beyond the maximum current rating, an
internal circuit will disrupt power and the screw feeder will produce an error code. Should
the screw feeder stop functioning, or exhibit abnormal or intermittent operation, please
discontinue use immediately and send the screw feeder to an authorized service center for
troubleshooting and repair.
• Turn the main power switch o when the screw feeder is not being used. Unplug the screw
feeder if it is not being used on a regular basis.
• Do not attempt to disassemble or repair the screw feeder. Repairs should only be
performed by qualied technicians properly trained in the safe operation, troubleshooting,
and repair of these devices. Please consult Delta Regis for the location of the nearest service
depot.
• Use only the factory specied Delta Regis brand replacement parts and accessories with
these screw feeders.
• Any damage to the screw feeder resulting from misuse, abuse, or failure to follow these
guidelines will void the limited product warranty.
Grounding — The AC power cord is equipped with a 3-prong electrical receptacle/plug with
ground pin. The screw feeder must be connected to a properly grounded AC electrical outlet. Do
not attempt to use this screw feeder without a properly functioning ground connection. Never
connect a live circuit to the ground pin or internal yellow-green ground wire.
DRFF-530R Screw Feeder
Operation and Setup Manual
www.deltaregis.com 3
Included Accessories
This machine has been set up according to the sample fasteners and/
ortechnicaldrawingyouhad providedusduringyourpurchase.If ne
tuning is required, please follow the instructions starting on page 5.
2.5mm hex key
AC Adapter with power cord
Grounding wire
(ESD applications)
Flat head screwdriver
DRFF-530R Screw Feeder
Operation and Setup Manual
www.deltaregis.com 4
Product Overview
1 - Rail Gates
2 - Power Switch
3 - Screw Present/Error LED
4 - Programming Key Pad w/ LCD
5 - DC Receptacle
6 - Grounding Lug
(ESD Applications)
7 - I/O Signal
1
1
2
3
4
567
DRFF-530R Screw Feeder
Operation and Setup Manual
www.deltaregis.com 5
User Adjustments
Screw Guide Plate
1. Locate and loosen highlighted screws using a 2mm hex key.
2. Using the included shims, insert under the screw head guide,
press down on the plate and tighten screws from step 1.
Remove shims.
DRFF-530R Screw Feeder
Operation and Setup Manual
www.deltaregis.com 6
User Adjustments
Screw Guide Plate (Continued)
3. Add several screws into the rail assembly. Tilt the screw
feeder forward, ensure the screws can smoothly pass under
the guide plate.
NOTE:
When adjusting the screw guide plate, the screws from step 1
must be fully tightened to avoid loosening during use.
Infrared Sensor Adjustment
1. Loosen the highlighted screws using a 2mm hex key.
DRFF-530R Screw Feeder
Operation and Setup Manual
www.deltaregis.com 7
Infrared Sensor Adjustment (Continued)
2. Adjust the infrared openings so only half of the opening is
exposed, tighten screws from step 1.
NOTE:
Only half of the infrared opening can be exposed. If
the screw cannot be detected, you can make further
adjustments.
DRFF-530R Screw Feeder
Operation and Setup Manual
www.deltaregis.com 8
User Adjustments
Brush Adjustment
1. Loosen the highlighted screws using a 2.5mm hex key.
DRFF-530R Screw Feeder
Operation and Setup Manual
www.deltaregis.com 9
User Adjustments
Brush Adjustment (Continued)
2. Insert several screws into the rail, under the brush.
Manually sweep the brush across the screw heads. Adjust
the brush so slightly touches the screw heads. Re-tighten
the screws from step 1.
NOTE:
The brush holder must not make contact with any surface of
the hopper. Ensure a gap exists to avoid jamming.
The brush bristles are tapered.
DRFF-530R Screw Feeder
Operation and Setup Manual
www.deltaregis.com 10
Filling the Hopper
Before lling the hopper, turn the machine OFF.
Remove the hopper cover. Check for debris or foreign objects.
Fill the hopper with screws leaving a minimum of 2 mm space
under the rail for thread lengths up to 5mm, 4mm space for
thread lengths over 5mm.
The hopper capacity is approximately 500cc (30.51ci).
Mixed screws, debris and/or foreign objects must be removed
to prevent poor performance.
2mm
2mm
4mm
4mm
Indice
Altri manuali Delta Regis Alimentatore di filo
Manuali Alimentatore di filo popolari di altre marche
Miller
Miller XR-AlumaFeed Suitcase Manuale utente
Lincoln Electric
Lincoln Electric Activ8X Manuale utente
Abicor Binzel
Abicor Binzel iROB Feed HA Manuale utente
EWM
EWM drive 4X IC D EX Manuale utente
Lincoln Electric
Lincoln Electric LF-72 Manuale utente
Hakko Electronics
Hakko Electronics 373 Manuale utente