DFI EC70B-SU Manuale utente

EC70B-SU Installation Guide

Package Contents

www.d.com

•

1 EC70B-SU system unit

•

Mounting screws for Mini PCIe modules

• Accessories for M.2 modules

•

1 Quick Installation Guide

•

1 CD disk includes:

- Drivers / Manual

Panel

Rear View

HDMI

Antenna

hole

COM 3 LAN 2

DC-in

USB 3.0

Line-out

Mic-in

Remote

power-on Switch

USB 3.0

Antenna

hole

8-bit DIOPoE

LAN 1

Front View Reset HDD LED

Status LED

(blue)

VGA

COM 5

COM 4/ 8-bit DIO

COM 6 USB 3.0CFast (2)

COM 2 (1)

COM 1(1)

Power with LED

(green)

Notes:

1. COM 1 and COM 2 can be selected among RS232, RS422 and RS485 whereas COM3 to COM 6 are

xed at RS232.

2. CFast slot is optional and only available upon request.

DFI reserves the right to change the specications at any time prior to the product's release. For the latest revision and details of the

installation process, please refer to the user's manual.

4. Lift the cover to open the system. The M.2 socket on the expansion board is

readily accessible after removing the bottom cover.

Chassis screw

Removing the Chassis Cover

Please observe the following guidelines and follow the procedure to open the

system.

1. Make sure the system and all other peripheral devices connected to it have been

powered-off.

2. Disconnect all power cords and cables.

3. The 2 mounting screws on the bottom of the system are used to secure the

cover to the chassis. Remove these screws and then put them in a safe place

for later use.

M.2 socekt

Installing an M.2 card

To install an 80mm M.2 SSD:

1. Align the notch at the edge of the M.2 card with the key in the connector.

2. Insert the M.2 card into the connector.

3. Use the provided mounting screw to secure the card on the system board.

To install a 42mm or 60mm M.2 SSD:

1. Install the standoff at the 42mm or 60mm mounting position.

2. Align the notch at the edge of the M.2 card with the key in the connector.

3. Insert the M.2 card into the connector.

4. Use the provided mounting screw to secure the card on the system board.

The system is equipped with one M.2 socket (SATA signals) and supports 42mm,

60mm and 80mm M.2 SSDs.

M.2 card

Standoff

Installing a Mini PCIe Card

Note:

The system also has a half-size Mini PCIe slot that can accommodate either a Mini PCIe or an mSATA card. Refer

to jumper settings for signal selection for this slot.

The system board is equipped with 2 Mini PCIe slots: one full-size and one half-

size slot. Here we will demonstrate the installation of a full-size Mini PCIe card.

The PCIe sockets are located on the main board; to access the main board, detach

the expansion board on top of it. Remove the screws that affix the front and

back bezels as shown in the following pictures to access the expansion board and

uninstall it from the system.

Mounting Screw

Use a wrench or a screwdriver with a

socket end to remove the fasteners

used on DE9 and VGA connectors.

Use a wrench to remove the

hexagonal gasket

2. Grasp the Mini PCIe card by its edges and align the notch of the PCIe card

with the key in the connector on the system board.

3. Push the Mini PCIe card down and use the provided mounting screw to secure

the card on the system board.

Board Layout and Jumper Settings

A46401730

Note:

You cannot use COM 4 and DIO at the same time.

Please set JP1 and JP2 together.

www.d.com

DC-in

Mini PCIe

Reset

Power

Front

Panel

(JP11)

DDR4 DDR4 DDR4 DDR4

COM 4

LAN 2 LAN 1

USB 2

USB 1

USB 3.0

USB 4

USB 3

COM 3

COM 2 COM 1

VGA

USB 3.0

SATA 3.0

SPI Flash

BIOS

JP2

JP1

Battery

JP7

Mini PCIe

MIC-inLINE-out

SATA 2 SATA Power

Realtek ALC888

Intel

WGI210AT

JP3

JP4

COM4/DIO Pin Select

Clear CMOS

Mini PCIe PCIe/

SATA Select

(JP3)

(JP4)

Auto PWR ON

(JP1)

(JP2)

(JP7)

EIO

(connects to the I/O board)

EIO

(connects to the I/O board)

COM4 / DIO Pin Select JP1

COM4 1-2, 4-5, 7-8,

10-11 On (default)

DIO 2-3, 5-6, 8-9,

11-12 On

COM4 / DIO Pin Select JP2

COM4 1-2, 4-5, 7-8,

10-11 On (default)

DIO 2-3, 5-6, 8-9,

11-12 On

Mini PCIe PCIe/SATA Select JP3

PCIe 2-3 On

SATA 1-2 On

(default)

Clear CMOS JP4

Normal 1-2 On (default)

Clear CMOS 2-3 On

Auto PWR ON JP7

Normal 1-2 On (default)

Auto-PWR ON 2-3 On

Altri manuali per EC70B-SU

Indice

Manuali Scrivania popolari di altre marche

HP m9060n - Pavilion - Elite Scheda tecnica

Asus

Asus E210 Series Manuale utente

Dell

Dell Inspiron 600m Manuale utente

Dell

Dell Inspiron 3662 Manuale utente

TotalFlow

TotalFlow uFLO Manuale utente

HP Presario SV7000 - Desktop PC Manuale utente

HP ProDesk 400 G5 Manuale

Logitech

Logitech MK320 Manuale utente

Dell

Dell XPS 730 H2C Manuale utente

Sony

Sony Vaio Series Manuale utente

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuale utente

Alto

Alto MD 250 Manuale utente

Lenovo

Lenovo ThinkCentre Edge 72 Manuale

Lenovo

Lenovo ThinkStation D20 Manuale

Arbor Technology

Arbor Technology FPC-7800 Series Manuale utente

Sony

Sony VAIO VGX-TP1 Series Manuale utente

Asus

Asus Eee Box B204 Manuale utente

Dell

Dell Optiplex 9010 All In One Manuale utente