DFI KS150 Manuale utente

KS150/190/215-SD Installation Guide

Package Contents

•

One 15", 19", or 21.5" Modular Touch Panel PC

•

3-pin Terminal Blcok Connector

•

SATA and Mini PCIe Installation Screws

DFI reserves the right to change the specications at any time prior to the

product's release. For the latest revision and more details of the installation

procedure, please refer to the user's manual on the website.

www.d.com

Panel

Front OSD Functions (only for models with front OSD)

Notes on OSD Settings:

The front OSD is capable of controlling the system in the following ways in addition to

its explicit functions.

1. System Power On/Off: Press the Backlight on/off button for 3 seconds.

2. Light Sensor On/Off: Press the Brightness up arrow for 3 seconds.

3. OSD Lock/Unlock: Press the Brightness down arrow for 3 seconds.

4. The Alarm LED has no funtion for the KS-SD Series.

Backlight or Power

on/off Volume Brightness

Power HDD Alarm LED

Bottom View

Top View

DC-in

DVI-D

(DVI-I connector)

LAN 1 LAN 2

VGA

USB 3.0

COM 2

Power Button

Reset Button

COM 3 COM 4

Status LED (Orange)

HDD LED (Red)

COM 1

Remote Power Switch

Removing the Chassis Cover

1. Make sure the system and all other peripheral devices connected to it

have been powered-off.

2. Disconnect all power cords and cables.

3. The 6 mounting screws on the rear side of the system are used to

secure the cover to the chassis. Remove these screws and put them in a

safe place for later use.

4. Lift the cover to open the system.

5. The Mini PCIe, M.2 and the SODIMM slots are readily accessible after

removing the chassis cover.

Mini PCIe

Sockets

SATA drive bay

Mounting Screw

The system can accommodate one SATA drive. Please use the following

procedure to install a SATA drive in the system.

1. Before installing the SATA drive, connect the SATA data/power cable

to the SATA data connector of the SATA drive. Then install the SATA

drive onto the HDD bracket with the provided mounting screws.

Installing a SATA Drive

Mounting Screws

Mounting screws

SATA data and power cable

2. Place the SATA drive installed with the HDD bracket in the system.

Align the mounting holes on the HDD bracket with the mounting holes

on the drive bay and use the provided mounting screws to secure the

drive in place.

Mounting Screws

3. Connect the other end of the SATA data/power cable to the SATA data

and power connectors on the system board respectively.

SATA power connector

SATA data connector

Installing a SODIMM

The system supports two DDR4 SODIMM socket. To install a memory mod-

ule, grasp the memory module by its edges and align the module’s notch

with the socket’s notch; then insert the memory into the socket at an

angle and push it down until you feel a click.

Notes:

1. The system supports dual-channel conguration. To enable dual-channel,

populate both SODIMM sockets.

2. If installing only one memory module, please install it on the memory socket

labeled DIMM 1 (the one closer to the edge of the board).

3. The SODIMM sockets can only accept DDR4 memory modules. Please do not

install other types of memory modules.

Insert the memory

at an angle

SODIMM module

installed into the socket

The system board is equipped with 2 Mini PCIe slots: one full-size and

(PCIe/USB signals) and one half-size slot (USB/mSATA signals). Here we will

demonstrate the installation of a full-size Mini PCIe card.

1. Grasp the Mini PCIe card by its edges and align the notch in the

connector of the Mini PCIe card with the notch in the connector on the

system board.

2. Push the Mini PCIe card down and use the provided mounting screw to

secure the card on the system board.

Installing a Mini PCIe or mSATA Card

Mounting screw

Antenna hole

0.82mm

Important:

The bottom side of a full-size Mini PCIe module should have a component height

restriction of 0.82 mm and will sit ush against the connected half-size Mini PCIe

module if such a component is used and the half-size slot is connected with a

module.

Assemble the Modular Panel PC

The modular panel PC comprises two parts: a box module and a panel module.

1. Take off the cover of the ADP connector. Hold the box module with its

ADP connector (female) in line with the ADP connector (male) of the

panel module. Align the box module with the panel module using the

alignment posts.

Note:

If the orientation of the assembly is not correct, the box module will not seat evenly on top

of the panel module, which results in some space in between them and indicates that the

ADP connectors are not engaged. When this is the case, please turn the box module the

other way around.

2. Hold the box module with its ADP connector (female) in line with the

ADP connector (male) of the panel module. Align the box module with

the panel module using the alignment posts.

ADP

connector

cover screw

ADP

Connector

(female)

Box Module

Alignment

Post

Panel Module

3. Seat the box module on top of the panel module with the alignment

post effortlessly sliping into the designated holes on the box module.

Press to install these two modules and secure the installation with 8

mouting screws.

Mounting Screw

Alignment

Post

Box + Panel Module

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Pannello touch popolari di altre marche

FlowLine

FlowLine Data loop Manuale utente

ALPEX

ALPEX AEx-8 P Series Manuale utente

Ltech

Ltech E5S Manuale utente

Harman

Harman AMX MODERO S MSD-701-L2 Manuale utente

Acnodes

Acnodes PC 1150 Manuale utente

AIS

AIS IP10IA99 series Manuale utente

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manuale utente

YASKAWA

YASKAWA TP 610C Manuale utente

B&R

B&R Power Panel C Series Manuale utente

Beijer Electronics

Beijer Electronics X2 control Manuale utente

AXIOMTEK

AXIOMTEK GOT321W-521 Manuale utente

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manuale utente

Qomo

Qomo QIT1386 Manuale utente

AMX

AMX AXP-PPC Guida

Sartorius

Sartorius X3 PR 5410 Manuale utente

AMX

AMX Modero X Series Manuale utente

Advantech

Advantech TPC-30 Series Manuale utente

B&R Industries

B&R Industries MAPPC900-ENG Manuale utente