DFI KSM-KH Series Manuale utente
1
KSM-KH Installation Guide
Package Contents
•
One 15", 19", or 21.5" Modular Touch Panel PC
•
Power cable with 3-plole teminal block connector
•
SATA, Mini PCIe and M.2 Installation Screws
•
Extended power switch cable
DFI reserves the right to change the specications at any time prior to the
product's release. For the latest revision and more details of the installation
procedure, please refer to the user's manual on the website.
www.d.com
2
Panel
Front OSD Functions (only for models with front OSD)
Notes on OSD Settings:
The front OSD is capable of controlling the system in the following ways in addition to
its explicit functions.
1. System Power On/O: Press the Backlight on/o button for 3 seconds.
2. Light Sensor On/O: Press the Brightness up arrow for 3 seconds.
3. OSD Lock/Unlock: Press the Brightness down arrow for 3 seconds.
4. The Alarm LED has no funtion for the KSM-KH Series.
Backlight or Power
on/o Volume Brightness
Power HDD Alarm LED
Bottom View
Top View
DC-in USB 3.0
DVI-D
(DVI-I connector)
LAN 1
LAN 2
VGA
HDMI (KSM-190)
COM 2
Power Button
(1)
Reset Button COM 3 COM 4
Status LED (Orange)
HDD LED (Red) COM 1
Extended Power
on/o Switch
USB 2.0
3
Removing the Chassis Cover
1. Make sure the system and all other peripheral devices connected to it
have been powered-o.
2. Disconnect all power cords and cables.
3. Remove mounting screws at each side of the system box.
4. Lift the cover to open the system.
5. The Mini PCIe, M.2 and the SODIMM slots are readily accessible after
removing the chassis cover.
SODIMM
Socket
Mini PCIe
Sockets
M.2 Socket
SATA drive bay
SIM card slot
4
The system can accommodate one SATA drive. Please use the following
procedure to install a SATA drive in the system.
1. Before installing the SATA drive, connect the SATA data/power cable
to the SATA data connector of the SATA drive. Then install the SATA
drive onto the HDD bracket with the provided mounting screws.
Installing a SATA Drive
Mounting Screws
Mounting screws
SATA data and power cable
2. Place the SATA drive installed with the HDD bracket in the system.
Align the mounting holes on the HDD bracket with the mounting holes
on the drive bay and use the provided mounting screws to secure the
drive in place.
Mounting Screws
5
3. Connect the other end of the SATA data/power cable to the SATA data
and power connectors on the system board respectively.
SATA power connector
SATA data connector
6
Installing a SODIMM
The system supports two DDR4 SODIMM socket. To install a memory mod-
ule, grasp the memory module by its edges and align the module’s notch
with the socket’s notch; then insert the memory into the socket at an
angle and push it down until you feel a click.
SODIMM module
installed into the socket
Notes:
1. The system supports dual-channel conguration. To enable dual-channel,
populate both SODIMM sockets.
2. If installing only one memory module, please install it on the memory socket
labeled DIMM 1 (the one closer to the center of the board).
3. The SODIMM sockets can only accept DDR4 memory modules. Please do not
install other types of memory modules. The SKUs with Intel®CM238 Chipset
support ECC memory.
Insert the memory
at an angle
7
Installing an M.2 Card
To install an M.2 card, insert the bottom edge of the M.2 card into the
connector, and then secure the card to the stando with the provided
mounting screw.
Mounting Screw
The onboard M.2 Type 2280 connector (M Key) supports PCIe NVMe
modules up to PCIe Gen 3.0 x4 bandwidth. Note that only SKUs with Intel®
QM175 Chipset support M.2 socket.
8
The system board is equipped with 2 Mini PCIe slots with SIM card sockets
to support a variety of wireless LAN and mobile broadband communication
modules. Mini PCIe slot 1 provides both USB and PCIe interfaces whereas
Mini PCIe slot 2 provides only USB interface.
1. Grasp the Mini PCIe card by its edges and align the notch in the
connector of the Mini PCIe card with the notch in the connector on the
system board.
2. Push the Mini PCIe card down and use the provided mounting screws to
secure the card on the system board.
Mounting screws
Installing a Mini PCIe Card and a SIM Card
Mini PCIE2
Mini PCIE1
9
Installing a SIM Card
Open the SIM card socket by pushing the white latch inward.
Insert the SIM card into the slot. Please place the card with the IC facing
down and the angled corner aligning with the socket's angled corner so it
will be correctly in contact with the system board.
Close the slot's cover and lock the slot by pushing the white latch outward.
Close the cover and lock it
Mini PCIE2Mini PCIE1
Push the latch inward
to open it Push the latch outward to
close it
Flip the cover up to open it
10
Assemble the Modular Panel PC
The modular panel PC comprises two parts: a box module and a panel module.
1. At the bottom of the box, there's a male ADP connector.
Note:
If the orientation of the assembly is not correct, the box module will not seat evenly on top
of the panel module, which results in some space in between them and indicates that the
ADP connectors are not engaged. When this is the case, please turn the box module the
other way around.
Alignment Post
2. Hold the box module with its ADP connector (female) in line with the
ADP connector (male) of the panel module. Align the box module with
the panel module using the alignment posts.
Box Module
Panel Module
ADP
Connector
(male)
Alignment Post
Questo manuale è adatto per i seguenti modelli
6
Indice
Altri manuali DFI Pannello touch
DFI
DFI KS070-AL Manuale utente
DFI
DFI KS150 Manuale utente
DFI
DFI KS310-IMX6 Manuale utente
DFI
DFI TPC150-SD Istruzioni operative e di manutenzione
DFI
DFI KS156-AL Manuale utente
DFI
DFI TPC150 Guida all'installazione
DFI
DFI KS-SD Series Manuale utente
DFI
DFI KS150-BT Manuale utente
DFI
DFI KS104-CD Manuale utente
DFI
DFI TPC170 Guida all'installazione
