Diamond Antenna MV3A Manuale utente

MV3A Mobile Antenna System

General Information

MV3A has 4 band capability—2m/6m, plus 2 HF bands though use of loading coils. The MV3A is supplied with HVC28 (10m) loading

coil. There are four optional HF coils available: HVC7 (40m), HVC14 (20m), HVC18 (17m), and HVC21 (15m). The MV3A has a fold-

over structure which allows for entrance into parking structures (i.e. garages, buildings, etc.). Use DIAMOND model MX62M Duplexer

for single antenna operation with ICOM IC-706, Yaesu FT100 or for combining HF & VHF transceivers.

Specifications

Bands Supplied 10m/6m/2m

Power, PEP: HF 120 watts / VHF 200 watts

Mount Connection: UHF

Length: 58” (with the HVC7 installed, total length is 80”)

VSWR: 1.5:1 Nominal–MV3A (10m/6m/2m)

Frequency: 2m: 144.5-148 MHz; 6m: 52-54* MHz;

(Nominal BW) 10m Loading Coil: 28-29 MHz (± 300 Khz)

HVC7 (40m): (± 28 Khz)

HVC14 (20m): (± 60 Khz)

HVC18 (17m): (±140 Khz)

HVC21 (15m): (± 180 Khz)

*6MSSB-EXT (6m SSB) (± 500 Khz)

Element Phasing: 5/8O2m, 1/4O6m

Recommended Antenna Mounts: Diamond K400C or K600M

Recommended Duplexer: Diamond MX62M

Installation Instructions

PRECAUTIONS:

(1) The MV3A requires vehicle ground.

(2) If installing HVC7 (40m) loading coil, install on top (vertical position) only. Some installations may require a nylon

cable to relieve stress on vehicle mount.

(3) The MV3A 6m/2m tuning assumes that at least one loading coil is mounted at the top end. VSWR may be out of

specification without the coil(s).

(1) Choose desired mounting location to insure maxi-

mum strength of mount, best performance of antenna, and

proper vehicle ground.

(2) Assemble MV3A with desired loading coil (HVC28

10m coil is included in package) and install on vehicle mount.

NOTE: Metric Hex wrenches are enclosed.

(3) With quality VSWR meter, check VSWR on all bands

to insure proper tuning of antenna. The loading coil rods

may require adjusting or trimming to reach best VSWR. If

it is necessary to trim coil rods, do so in 1/8” increments

only, until lowest VSWR is obtained at desired center fre-

quency. Shortening coil rods will have the effect of raising

the resonant frequency. Check both the high and low band-

width edges before cutting.

—10m Coil

MV3A Parts List

Discharge Protection Cap

Trim element with cutting de-

vice appropriate for cutting

metal. (i.e. Hacksaw, etc.)

Metric Hex Wrench M4

(4) When tuning optional loading coils (HVC7, HVC14, HVC18,

HVC21 and HVC28-10m coil), install on the top (vertical position) and

proceed to tune the coils by adjusting or trimming coil rods. (NOTE: HVC

Tuning Coils have a limited tuning range–refer to “frequency” under speci-

fications for bandwidth). Choose your desired center frequency as a guide

for tuning range and adjust for best VSWR at center frequency.

(5) Once you have adjusted all coils for best VSWR in the vertical posi-

tion, you may assemble one optional coil horizontally. All coils can work

horizontally except the HVC7 (40m); it must be in the vertical position due

to its size. The VSWR will change slightly by adding a coil horizontal; there-

fore, it is best to check your VSWR readings to verify tuning.

(6) To replace loading coils, simply unscrew coil from coil support

bracket and replace with another coil (see illustration). Be sure loading

coils are fastened securely so they don't loosen from vehicle and road

vibration.

(7) The MV3A has a fold-over structure for situations where the

antenna height is a problem (see illustration). Simply unscrew the

fold-over lock, lift up, and tilt over 90°. Care should be taken when

folding over, not to damage vehicle or any loading coils. Do not

drive with antenna in the folded position.

MX62M Duplexer

LPF 1.6-56; HPF 76-470

Power; 200w CW, 600w PEP

Connectors: Mix-UHF(F);

Ports-UHF(M)

w/12” cable

K400C

Trunk/Hatchback Mount

Deluxe UHF type base

Dual-axis adjustable

6½” RG316 Teflon Coax

w/PL-259.

Use Diamond Model C110

for front radio installations.

K600M

Trunk Mount

Deluxe trunk mount.

16.5' RG188 and 7mm 5D Coax.

Tilt Angle (0-9°)

MV3A Accessory Items

— 40m

—20m

—17m —15m

—10m

HVC Loading Coils

HF Mobile Installation Tips

With all the different types of installations possible, there are many unique problems that can occur. We have compiled some additional

notes on specified areas.

(1) GROUNDING ANTENNA: Obtaining a good ground is very important to any HF mobile installation. No matter where your

antenna is mounted, it is highly recommended your run a heavy copper strap or braid (1” to 3”) between body and frame of your vehicle.

(NOTE: Copper wire is not sufficient!) If you have ignition noise problems, it is also recommended to ground the end of your tail pipe to

the frame.1

(2) OPTIMUM MOUNTING LOCATION: You should always mount your antenna as high on your vehicle and as far away

horizontally from other metal objects as possible. The center of your roof is the best location; however, this is not always practical or

possible for most HF antenna installations. The next best location is in the center of the driver's side of the trunk (side mounted on driver

side to avoid low hanging curbside branches or objects). The DIAMOND K400C and K600M series mounts work well with the MV3A.

The front or rear bumper is another possible mounting location; however, due to high ground loss, this should be last choice. If you must

use a bumper mount, it is recommended to use a base extension to raise bottom of antenna to equal height of top of trunk. Grounding of

this extension will become important.

(3) TRUNK LID MOUNTING: Probably the best mounting location for most vehicles. Usually, adding one or two copper straps

from the hinge area to car body will improve grounding (and thereby antenna tuning). It is necessary that at least two of the four

sockethead screws on mount penetrate paint to metal for proper grounding. (A little clear nail polish or other acrylic paint may be used

to seal around mounting screws.)

(4) COAX: If you use an antenna mount other than DIAMOND ANTENNA models K400C or K600M, it is very important to use

a quality 52 ohm coax (RG8U, RG58U, RG213, Teflon Coax, etc. with at least 95% shield and stranded center conductor). Do not use

foam coax or coaxes with solid center conductors. Foam coax can deform in heat and absorb moisture, solid center conductor coaxes

have less flexibility and may become brittle and break in mobile applications.

(5) EMI: Electromagnetic Interference is the single greatest concern for HF mobile applications. Route your cable as far from the

vehicles ECM (Engine Control Module) and vehicle's electrical systems as possible. Sometimes a ferrite choke may be required on coax

near mount. There are many books on the subject of interference, refer to endnotes for additional information.2

1. J. Seybold, “HF Mobile Installation Tips”, December 1995 QST, pg. 58-60.

2. ARRL, Radio Frequency Interference Tips: How to find it and fix it., The book is available from your favorite amateur radio dealer

or ARRL headquarters.

Diamond Antennas and Meters are distributed by

RF Parts Company•435 S. Pacific Street•San Marcos, CA 92078 •(760) 744-0900

VSWR Charts

HVC7

HVC14 HVC18

HVC21 HVC28

WARNINGS:

(1) Bolts and set screws on antenna and mounting bracket may

loosen from vehicle and vibration. Be sure to check periodically to

ensure they are fastened securely.

(2) Avoid obstacles such as tree branches or low overpasses;

impact with these obstacles will cause antenna to break.

(3) The MV3A is not recommended for either magnet type mounts

or installation on large GVW vehicles.

(4) Avoid touching antenna while transmitting.

(5) Do not scratch or remove rubber covering on loading coil

sections.

(6) Avoid driving with antenna in folded position.

6MSSB-EXT

SSB extension rod for MV3A

The 6MSSB-EXT lowers the 6m resonant frequency of MV3A for 50.1 operation.

NOTE: With 6MSSB-EXT installed, you will lose 2m capability of MV3A.

Installation: (You have two installation options.)

(1) If using one HF coil, simply install in horizontal loading coil support bracket #67402. Follow tuning

instructions below.

(2) If using two HF coils, remove set screw #67403 from horizontal loading coil support bracket #67402. Attach

6MSSB-EXT and fasten lock nut. Follow tuning instructions below.

Tuning Instructions: With quality VSWR meter, check VSWR on lower portion of 6M (approx. 50.125 MHz). The

extension rod may require adjusting or trimming to reach best VSWR. If trimming is required, do so in 1/8” increments

only, until lowest VSWR is obtained. Shorting extension rod will have the effect of raising the resonant frequency.

Check both the high and low bandwidth edges before cutting.

Altri manuali Diamond Antenna Antenna

Diamond Antenna

Diamond Antenna HF6CL Manuale utente

Diamond Antenna

Diamond Antenna X300NA Manuale utente

Diamond Antenna

Diamond Antenna CR-10H Manuale utente

Diamond Antenna

Diamond Antenna CP-725H Manuale utente

Diamond Antenna

Diamond Antenna V2000A Manuale utente

Diamond Antenna

Diamond Antenna CP6 Manuale utente

Diamond Antenna

Diamond Antenna HV7A Manuale utente

Diamond Antenna

Diamond Antenna D-130J Manuale utente

Diamond Antenna

Diamond Antenna W-8010 Manuale utente

Diamond Antenna

Diamond Antenna K400 Manuale utente

Diamond Antenna

Diamond Antenna 150MVHS Manuale utente

Diamond Antenna

Diamond Antenna SG-M911 Manuale utente

Diamond Antenna

Diamond Antenna F-718 Series Manuale utente

Diamond Antenna

Diamond Antenna HFV8040 Manuale utente

Diamond Antenna

Diamond Antenna A144S10 Manuale utente

Diamond Antenna

Diamond Antenna BB7V Manuale utente

Diamond Antenna

Diamond Antenna SG-M510 Manuale utente

Diamond Antenna

Diamond Antenna A144-S5 Manuale utente

Diamond Antenna

Diamond Antenna KV5 Manuale utente

Diamond Antenna

Diamond Antenna A430S10 Manuale utente

Diamond Antenna

Diamond Antenna W-735 Manuale tecnico

Diamond Antenna

Diamond Antenna X500HNA Manuale utente

Diamond Antenna

Diamond Antenna BB6W Manuale utente

Diamond Antenna

Diamond Antenna BB2M Manuale utente

Manuali Antenna popolari di altre marche

Alfa Network

Alfa Network APA-L01 Manuale utente

Naval

Naval PR-422CA Manuale utente

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuale utente

TERK Technologies

TERK Technologies TV44 Manuale utente

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuale utente

HP J8999A Manuale utente

MobilSat

MobilSat MSP-S Manuale utente

Steren

Steren ANT-UHF 13 Manuale utente

Novatel

Novatel 600-G Manuale operativo

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuale utente

TRENDnet

TRENDnet TEW-AO12O Manuale utente

Radio Shack

Radio Shack 15-1837 Manuale utente

CommScope

CommScope CMAX-OMFX-43M-I53 Manuale utente

Ramsey Electronics

Ramsey Electronics DAP25 Manuale utente

COBHAM

COBHAM SAILOR 800 VSAT Manuale per l'uso e la cura

Trango Systems

Trango Systems AD900-9 Manuale utente

Steren

Steren ANT-100 Manuale utente

Proxim

Proxim 5054-PA-23 Manuale utente