Digi-tech BP355 Manuale utente

MAKING CONNECTIONS / APPLYING POWER BYPASSING EFFECTS & USING THE TUNER

WHAT’S IN THE BOX

• BP355 Bass Multi-Eects Processor & USB Recording Interface

• Power Supply

To activate your warranty, please register at

http://digitech.com/en-US/support/warranty_registration.

GET X-EDIT

To get the X-Edit software, visit

http://digitech.com/en-US/products/bp355#downloads.

GET THE OWNER’S MANUAL

Scan the QR code to get the owner’s manual or visit

http://digitech.com/en-US/products/bp355#documentation.

1 2

Live Application Recording / Practice Application

A. Set your bass amp(s) to a clean tone, set

the tone controls for a at EQ response

(on most amps, this would be 0 or 5

on the tone controls), turn the volume

control(s) all the way down, then power

o the amp(s). If connecting to a mixer,

fully lower the corresponding channel

fader(s).

B. Make connections as shown in the

diagrams to the right, depending on

application type.

C. Connect the included power supply to

the POWER input jack and plug it into

an available AC outlet.

D. Set the BP355’s MASTER LEVEL control

to 75.

E. Power on your bass amp(s). slowly

raise the amp volume control(s) for the

desired volume. If using a mixer, adjust

each channel’s gain/trim and fader

controls for the desired volume.

A. To bypass eects, press the UP and DOWN

footswitches simultaneously.The display

will read “BYPASS”.

B. To exit Bypass mode, press any footswitch.

C. To use theTuner, press and hold the UP

and DOWN footswitches simultaneously

for 2 seconds. The display will briey read

“TUNER” then enter Tuner mode.

D. Play a note on the bass. The note will be

shown in the display and the LEDs on the

left will indicate if the note is sharp, at, or

in tune.

E. To exit Tuner mode, press any footswitch.

Press for Bypass, hold forTuner

Sharp

Flat

In Tune

QUICK START GUIDE

SELECTING, EDITING, & STORING PRESETS SWITCHING AMPS & USING STOMP MODE USING THE DRUMS / LOOPER

3 4 5

DigiTech is a registered trademark of Harman.

DigiTech

• 801.566.8800 • digitech.com

PN: 5059481-A

A. To toggle between amps A and B, press the

AMP A-B footswitch. Amps can be edited by

following the instructions in step 3 and selecting

“AMPLIFIER” in step 3B. Pressing the AMP A-B

footswitch will then switch between amps for

editing.

NOTE: Amps cannot be toggled when in Stomp

mode.

B. To use Stomp mode, press the AMP A-B and UP

footswitches simultaneously.The display will

briey read “STOMP”, indicating Stomp mode is

now active.

C. Pressing the 3 footswitches will now turn the

“DISTORTION”, “CHORUS / FX”, and “DELAY”eects

on and o.

D. To exit Stomp mode, press the AMP A-B and UP

footswitches simultaneously again. The display

will briey read “PRESET”, indicating that the UP

and DOWN footswitches will once again select

presets.

A. To enable the Drums, press the DRUMS button.

Drum settings can be edited by following the

instructions in step 3B and selecting the “LOOPER”

row in the matrix.

B. To use the Looper, make sure the DRUMS button

is o. Then press and hold the LOOPER footswitch

for 2 seconds. The display will read“LOOPER”,

indicating Looper mode is now active.

C. Press the LOOPER footswitch to arm the looper for

recording. The display will read “ARMED”.

D. Begin playing. When done, press the LOOPER

footswitch again on the same downbeat you

started on.

E. While the loop is playing, press and hold the

LOOPER footswitch to record overdubs.

F. Press the LOOPER footswitch to stop and play the

looper.

G. To clear the loop, stop playback then press and

hold the LOOPER footswitch for 2 seconds.

H. To exit the Looper, stop playback then press and

hold the LOOPER footswitch for 2 seconds.

A. To select a preset, press the UP or DOWN footswitch.

B. Turn the TONE LIBRARY and EFFECTS

LIBRARY knobs to select other tones/

eect chains.

C. Press the UP/DOWN EDIT buttons to

select a specic eect for editing (the

selected eect LED will light). Press the

TONE LIBRARY knob to turn the eect

on/o. Look at the parameter matrix

and use the KNOBS to edit the eect.

D. To exit Edit mode, press the UP or

DOWN footswitch.

E. To store the preset, press the STORE

button.

F. Use the TONE LIBRARY and EFFECTS

LIBRARY knobs to edit the preset name.

G. Press the STORE button a 2nd time.

H. Optional: Press the UP or DOWN

footswitch to relocate the preset.

I. Press the STORE button a 3rd time to

store the preset.

Drums

on/o

Press to enter/exit

Stomp mode

Press to

toggle Amps

Hold to enter/exit Looper,

press to operate Looper

Press for

Preset up

Press for

Preset down

Selected

eect

Press to

edit eect

Altri manuali per BP355

Altri manuali digi-tech Apparecchiature di registrazione

digi-tech

digi-tech DSP256 Manuale utente

digi-tech

digi-tech QUAD 400 SYSEX1.0 Manuale utente

digi-tech

digi-tech BP-8 Valve Manuale utente

digi-tech

digi-tech RP-20 VALVE Manuale utente

digi-tech

digi-tech TSR24S Manuale utente

digi-tech

digi-tech STUDIO5000 Manuale utente

digi-tech

digi-tech DSP 16 Manuale utente

digi-tech

digi-tech HARDWIRE DL-8 Manuale utente

digi-tech

digi-tech RP 2000 Manuale utente

digi-tech

digi-tech HardWire RV-7 Manuale utente

digi-tech

digi-tech TSR6 Manuale utente

digi-tech

digi-tech Vocalist Live FX Manuale utente

digi-tech

digi-tech RP-1 Manuale utente

digi-tech

digi-tech BP50 Manuale utente

digi-tech

digi-tech VOCAL 300 Manuale utente

digi-tech

digi-tech S100 Manuale utente

digi-tech

digi-tech Control Seven Manuale utente

digi-tech

digi-tech DSP-128 Manuale utente

digi-tech

digi-tech Artist GSP-2101 Manuale utente

digi-tech

digi-tech QUAD4 Manuale utente

digi-tech

digi-tech RP-7 VALVE Manuale utente

digi-tech

digi-tech DIGIVERB Manuale utente

digi-tech

digi-tech RPX400 Manuale utente

digi-tech

digi-tech RP1000 Manuale utente

Manuali Apparecchiature di registrazione popolari di altre marche

KV2 Audio

KV2 Audio 500 Series Manuale utente

Robotics Technologies

Robotics Technologies microBus-Cam II Manuale utente

Seca

Seca 460 Manuale utente

Cognex

Cognex MVS-8000 Series Manuale utente

Mect

Mect MPNC006 Series Manuale utente

Bad Caf

Bad Caf THE LEASH Manuale utente

Strymon

Strymon NIGHTSKY Manuale utente

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente

Tews Technologies

Tews Technologies TPMC465 Manuale utente

Honeywell

Honeywell Excel 50 Manuale utente

SeaLevel

SeaLevel COMM+8.LPCI Manuale utente

Arturia

Arturia AUDIOFUSE STUDIO Manuale utente

Rukra

Rukra RK-1240 Manuale utente

Samson

Samson SCOM Manuale utente

Dynacord

Dynacord DPS260 Manuale utente

Nice

Nice Core Manuale utente

Pyle Pro

Pyle Pro PSS8 Manuale utente

RF-System

RF-System TinyGate Manuale per l'uso e la cura

digi-tech BP355 Manuale utente

Manuali Apparecchiature di registrazione popolari di altre marche