Diginet LEDsmart+ MultiMate MMTM/PB Manuale utente
Setup Functions Guide
MMTM/PB
www.glg.lighting
Push Button Minute Timer
Programmable between 1 minute and 30 minutes with built in multi-way control
Push Button Minute Timer
2
Timer Setup
The LEDsmart+push button timer has a number of useful functions which can easily be set up by entering setup mode and
following the four easy steps.
The TIMEOUT PERIOD should always be set up. The other settings are optional, depending on the application. To set the
timeout period now, go to the next page.
Timer Setup Functions
Function
See Part
Setting the Timeout period
A
Setting Maximum Brightness
B
Setting Advanced Timer Features
C
Setting Off State LED Feature
D
Converting from minute to hour
timer
E
Setting MultiMate™Mode
F
Factory Defaults Reset
G
A: Entering Setup Mode
If the timer has been powered up for LESS THAN 15 MINUTES see A1.
If the timer has been powered up for MORE THAN 15 MINUTES see A2.
Once in Setup Mode, options are selected by a series of ‘clicks’ of the push button. Each ‘click’ should be within 1 second
of the previous click.
Push Button Minute Timer
3
A1: Timer has been powered up via mains 240Vac for LESS THAN 15 MINUTES
Step 1
Press and hold the button for 10 seconds
Note: Connected lights will dim up or down, this is normal
Step 2
The white LED Indicators will blink ON/OFF twice per second. This indicates that
the timer is now in Setup Mode
Note: If more than one LEDsmart+minute timer is connected in parallel, all these
timers will now enter setup mode. The blink ON/OFF will also be seen on all
other LEDsmart+minute timers connected in parallel
Step 3
The timer is ready for the settings to be adjusted as required. Go to the relevant
setup function instructions
A2: Timer has been powered up via mains 240Vac for MORE THAN 15 MINUTES
Step 1
Press and hold the button for 30 seconds
Note: This resets the Setup Entry time back to 10 seconds (for the next 30
minutes)
Note: Connected lights will dim up or down, this is normal
Step 2
The white LED Indicators will blink ON/OFF twice per second. This indicates that
the timer is now in Setup Mode
Note: If more than one LEDsmart+minute timer is connected in parallel, all these
timers will now enter setup mode. The blink ON/OFF will also be seen on all
other LEDsmart+minute timers connected in parallel
Step 3
The timer is ready for the settings to be adjusted as required. Go to the relevant
setup function instructions
Push Button Minute Timer
4
B: Setting the Timeout Interval
The Minutes timer allows a timeout duration of between 1 to 30 minutes in increments of 1 minute.
Out of the box (factory defaults), the time out interval is set to 15 minutes.
To change the time out interval from the default 15 minutes, follow the steps below.
Step 1
Enter into the timer Setup Mode - See PART A
Step 2
Click the push button 2 times
Step 3
The LED Indicator will blink 2 times
Note: To cancel/exit do nothing for 30 seconds
Step 4
To set the time out interval, push and hold the button and count the number
of blinks. Each blink of the indicator adds 1 minute to the minute timer
Step 5
When the number of blinks counted equals the number of minutes required,
release the button
The time out interval is saved and setup will exit automatically
Note
During normal use the indicator will blink when the timer is turned on to
indicate it is in time out mode
Trying to select a time interval of 0 will result in setting 1 minute timeout
The timeout period on Minute Timers connected in parallel need to be set
individually. The same timeout is not automatically set across units
Push Button Minute Timer
5
C: Setting Maximum Brightness
The maximum brightness level provided by the timer can be set to suit customer requirements.
Note that when lamps are near to full brightness, it is difficult to see changes in dimming level. Therefore, when setting up
maximum brightness, it is recommended that the lamp is slowly dimmed up to a point where no further changes in brightness
can be seen, and the maximum level set at this point.
Step 1
Enter into the timer Setup Mode - See PART A
Step 2
Click the push button 3 times
Step 3
The LED Indicator will blink 3 times
Note: To cancel/exit do nothing for 30 seconds
Note: If more than one dimmer is connected to the same load, all dimmers connected
to this load will now blink 3 times
Step 4
Push the button to achieve the required maximum brightness level
Note: To cancel/exit do nothing for 30 seconds
Step 5
Click once to save & exit
Note: If more than one LEDsmart+device is connected in parallel, the minimum
brightness levels only needs to be set in one device. The setting is automatically saved
to all other devices connected in parallel
Push Button Minute Timer
6
D: Setting Advanced Timer Mode
The advanced timer mode provides an optional advanced warning to the user that the lights will shortly turn off automatically.
When the advance timer is enabled, at time out the lights are dimmed to 50% over a 4 second period and are held at this 50%
level for 5 minutes. After this 5 minutes, the lights are turned off automatically.
Step 1
Enter into the timer Setup Mode - See PART A
Step 2
Click the push button 4 times
Step 3
The LED Indicator will blink 4 times
Note: To cancel/exit do nothing for 30 seconds
Step 4
To enable the advanced timer mode
Push and hold the button until the lamps(s) turn ON
To disable the advanced timer mode
Push and hold the button until the lamps(s) turn OFF (default)
Note: To cancel/exit do nothing for 30 seconds
Step 5
Click once to save & exit
Note that during this Advanced Timer 5 minute warning period:-
• The LED indicators will blink at a faster rate
• A tap of the push button will restore the load to 100%
ON and the timer will restart
• A long press of the push button will turn the load OFF.
Push Button Minute Timer
7
E: Setting Off State Indication
When the timer is switched off, the white LED indicators in the timer can be set to glow or turn off.
By Default, the white LED indicators are set to glow when the timer is turned off.
To set the LED indicators to turn off when the timer is off, follow the steps below.
Step 1
Enter into the timer Setup Mode - See PART A
Step 2
Click the push button 5 times
Step 3
The LED Indicator will blink 5 times
Note: To cancel/exit do nothing for 30 seconds
Step 4
To set Indicator to glow on when timer is off
Push the button until the lamp(s) turns ON
To set Indicator to turn off when timer is off
Push the button until the lamp(s) turns OFF
Note: To cancel/exit do nothing for 30 seconds
Step 5
Click once to save & exit
Push Button Minute Timer
8
F: Convert Minute to Hour Timer
If required, this minute timer can be converted to a standard LEDsmart hour timer, with a time out settable between ¼ hour and
7½ hours, in ¼ hour increments.
To convert to an hour timer, follow the steps below.
Step 1
Enter into the timer Setup Mode - See PART A
Step 2
Click the push button 6 times
Step 3
The LED Indicator will blink 6 times
Note: To cancel/exit do nothing for 30 seconds
Step 4
To change operation to hour timer mode
Push and hold the button until the lamps(s) turn ON
To change operation to minute timer mode (Set minute timer mode)
Push and hold the button until the lamps(s) turn OFF (default)
Note: To cancel/exit do nothing for 30 seconds
Step 5
Click once to save & exit
Push Button Minute Timer
9
G: Setting Multimate™ Mode
Step 1
Enter into the timer Setup Mode - See PART A
Step 2
Click the push button 8 times
Step 3
LED will blink 8 times
a. If the MultiMate™function is currently Disabled, lamp(s) connected to
the dimmer will now turn OFF
b. If the MultiMate™function is currently Enabled, lamps(s) connected to
the dimmer will now turn ON
Note: To cancel/exit do nothing for 30 seconds
Step 4
To Enable MultiMate™(Default) push-and-hold the button until the lamp(s) turns ON
To Disable MultiMate™push-and-hold the button until the lamp(s) turns OFF
Note: To cancel/exit do nothing for 30 seconds
Step 5
Click once to save & exit
Push Button Minute Timer
10
H: Resetting to Factory Default
Step 1
Enter into the timer Setup Mode - See PART A
Step 2
Click the push button 10 times
Step 3
The timer will automatically exit Setup Mode once
reset
Indice
