Digitalview IE-1000 Manuale utente

Specifications subject to change without notice

IMAGE ENHANCER ADD-ON BOARD

FOR 120Hz PANEL

Model: IE-1000

Part number : 417190021-3 or up

[Firmware version : V1.80.00]

INSTRUCTIONS

CONTENTS

Page: 2. Introduction, How to Proceed, Usage Note, Disclaimer

3. System design – Diagram of a suggested system

4. Assembly notes – Important information about system elements

6. Connection & Operation – How to use the IE-1000

8. Connectors, pinouts & jumpers – Essential connection information

13. Board dimensions

14. Troubleshooting

15. Specifications

16 Appendix I – Mapping definition

18. Warranty, Caution & Limitation of Liability, Trademarks

19. Contact details

It is essential that these instructions are read and understood before connecting or

powering up the IE-1000

Specifications subject to change without notice

Introduction

The IE-1000 is a Digital View add-on board providing:

•10 bit panel support and 120Hz panel support with motion compensation frame interpolation

for smoother motion

The IE-1000 can currently be matched with the Digital View SVH-1920 and upcoming SVX-1920

controllers to provide support for:

•Displays up to 1920x1200, 10 bit, 120Hz.

HOW TO PROCEED

•As most panels require different connection settings and cables it is important to have the

relevant Digital View Connection Diagram before assembly begins. This is obtainable from

the Digital View website as follows:

•Ensure all parts are on hand.

•Check controller and add-on board switch & jumper settings (errors may damage the panel)

•Prepare the source

•Connect the parts

•Understand the operation & functions

IMPORTANT USAGE NOTE

This equipment is for use by system manufacturers, developers and qualified integrators, the

manufacturer accepts no liability for damage or injury caused by the use of this product. It is

the responsibility of the developer, integrators or other user of this product to:

•Ensure that all necessary and appropriate safety measures are taken.

•Obtain suitable regulatory approvals as may be required.

•Check power settings to all component parts before connection.

DISCLAIMER

There is no implied or expressed warranty regarding this material.

Controller Solution Generator

A web based resource matching controllers & panels with connection diagrams

for download. Visit : http://www.digitalview.com/controllers/csg.php

Specifications subject to change without notice

SYSTEM DESIGN

A typical LCD based display system utilizing the IE-1000 is likely to comprise the following:

Summary:

1. LCD panel

2. Image Enhancer board, IE-1000

3. LCD controller card

4. Interconnect LVDS cable (P/N 426497600-3, 200mm)

5. Panel power cable (if required)

6. Panel cable for LVDS panel

7. RS-232 interface (for firmware upgrade only)

8. +12V / +24V DC power input

9. Power and inverter control cable

Digital View provides a range of parts, such as listed above, to make up complete display solutions.

Specifications subject to change without notice

ASSEMBLY NOTES

The IE-1000 is designed for monitor and custom display projects using 1920x1200 or 1920x1080

resolution 10 bit 120Hz TFT panels with connection with compatible Digital View controllers. The

following provides some guidelines for installation and preparation of a finished display solution.

Preparation: Before proceeding it is important to familiarize yourself with the parts making up the

system and the various connectors, mounting holes and general layout of the IE-1000. As much as

possible connectors have been labeled. Guides to connectors and mounting holes are shown in the

following relevant sections.

1. LCD Panel: The IE-1000 is designed for driving 10 bits 120Hz up to 1920x1200 LVDS panels.

Due to the variation between manufacturers of panels signal timing and other panel

characteristics it is important to use the correct Digital View Connection Diagram (which can be

downloaded from the Digital View Controller Solution Generator at

www.digitalview.com/controllers/csg.php) before connecting to a panel.

2. Image Enhancer board, IE-1000 : With reference to the Connection Diagram ensure correct

jumper and dip switches settings to match the target LCD panel. Caution: Handle with care as

static charge may damage electronic components.

3. LCD main controller, eg SVH-1920 : With reference to the Connection Diagram ensure correct

jumper and dip switches settings to match the target LCD panel. Caution: Handle the controller

with care as static charge may damage electronic components.

4. Interconnect LVDS cable : This cable connects between the IE-1000 and DigitalView controllers

for transmittion of LVDS signal and panel power to IE-1000 board. It is recommended to organize

loose wires with cable ties. Care should be taken when placing the cables to avoid signal

interference. Additionally it may be necessary in some systems to add ferrite cores to the cable to

minimize signal noise.

5. Panel power cable : This cable connects between IE-1000 and DigitalView controllers for panel

power.

6. Panel cable for LVDS panel : In order to provide a clean signal it is recommended that LCD

signal cables should not be longer than 61cm (24 inches). It is recommended to organize loose

wires with cable ties. Care should be taken when placing the cables to avoid signal interference.

Additionally it may be necessary in some systems to add ferrite cores to the cable to minimize

signal noise.

7. RS-232 interface : This port is relevant for firmware upgrade only.

8. Power Input: 12V/24VDC is required, this should be a regulated supply. The power rating

depends on the panel and inverter used. Normally a power supply with at least 15W power

output should adequate. Although the controller provides power regulation for the LCD power

this does not relate to the power supplied to the backlight inverter. If an unregulated power

supply is provided to an inverter any fluctuations in power may affect operation, performance and

lifetime of the inverter and or backlight tubes.

9. Power and inverter control cable : Different inverter models require different cables and

different pin assignments. Using the wrong cable may damage the inverter.

IMPORTANT NOTES

•Power Safety: We strongly advise using appropriate insulation for all circuitry.

•EMI: Shielding will be required for passing certain regulatory emissions tests.

•Ground: The various PCB mounting holes are connected to the ground plane.

Specifications subject to change without notice

•Servicing: The board is not user serviceable or repairable. Warranty does not cover

user error in connecting up to the IE-1000 and is invalidated by unauthorized

modification or repairs.

•Board Mounting: It is recommended that a clearance of at least 10mm is provided above

and 5mm below the board when mounted. Additionally consideration should be given to:

oElectrical insulation.

oGrounding.

oEMI shielding.

oCable management. Note: It is important to keep panel signal cables apart from the

inverter & backlight cables to prevent signal interference.

oHeat & Ventilation: Heat generated from other sources, for example the backlight of a

very high brightness panel may generate significant heat which could adversely affect

the IE-1000.

oOther system design issues that may affect safety or performance.

IMPORTANT: Please read the Application Notes section for more information.

Specifications subject to change without notice

CONNECTION & OPERATION

CAUTION: Never connect or disconnect parts of the display system when the system is powered up

as this may cause serious damage.

CONNECTION

Connection and usage is quite straight forward (it is useful to have the relevant connection diagram

available at this time):

1. Connect the LCD panel & IE-1000 : Use the appropriate panel cable as indicated in the relevant

Digital View Connection Diagram.

2. Connect the Digital View main controller & IE-1000:Use LVDS cable P/N 426497600-3,

200mm, this carries both the LVDS signal and panel power.

3. Connect a suitable OSD switch mount kit : Digital View offer a number of ready made options.

4. Check all Jumpers & Switches: Refer to the relevant Digital View Connection Diagram or the

jumpers and switches setting table (in the following section).

5. Connect the Power supply : Plug a DC 12V/24V power source to the connector PP1 or

PP2/PP3. You can consider to use Digital View mating power cable P/N 426013800-3, 160mm for

PP1 connection.

6. Power on : Switch on the controller board and panel by using the OSD switch mount.

Power status on LED5A :

State LED color

Power on state Green

Board status LED on LED1A :

State LED color

Board in operation with valid

signal. GREEN

No signal state RED

Valid signal detected and

board setup in progress ORANGE

General:

•If you are using supplied cables & accessories, ensure they are correct for the model of panel and

controller and IE-1000.

•If you are making your own cables & connectors refer carefully to both the panel & inverter

specifications and the section in this manual, “Connectors, Pinouts & Jumpers” to ensure the

correct pin to pin wiring.

Specifications subject to change without notice

IE-1000 BUTTONS & DEMO MODES

•Button switch – TS1 : Board reset : Reset the IE-1000 board.

•Button switch – TS2 : Push TS2 to cycle between the 4 different demo modes while LED1A is

GREEN.

Mode 1 (default) = whole screen with smoothed motion (LED2 GREEN);

Mode 2 = LEFT demo mode, left side of screen with smoothed motion while right side without (LED2

GREEN, a box with yellow border appear on LEFT hand side of screen);

Mode 3 = CENTRE demo mode, centre part of screen with smoothed motion while other areas

without (LED2 GREEN, a box with yellow border appear in the CENTRE of the screen);

Mode 4 = whole screen without smoothed motion (LED2 RED)

IE-1000 will not memorize the demo mode after you turn off the IE-1000. It will resume back to mode

1 always.

* This function will not activate in static text mode (SW2 position 4 sets ON).

Specifications subject to change without notice

CONNECTORS, PINOUTS & JUMPERS

The various connectors are:

Summary: Connectors

Ref Purpose Description

CN1 LVDS signal input Hirose 40-pin, DF13A-40DP-1.25DSA

(Matching type : DF13-40DS-1.25C)

(Matching panel cable : P/N 426497600-3, 200mm)

CN2 Additional panel power input Hirose 20-pin, DF13-20DP-1.25 (Matching type : DF13-20DS-1.25C)

CN3 LVDS signal output 1 JST 50-pin, BM50B-SRDS

(Matching type : SHDR-50V-S-B or compatible)

CN4 LVDS signal output 2 JST 40-pin, BM40B-SRDS

(Matching type : SHDR-40V-S-B or compatible)

CN5 Reserved JST 4-pin, S4B-XH-A (Matching type : XHP-4)

CN6 Serial control (for firmware

programming use only) JST 6-pin, S6B-XH-A (Matching type : XHP-6)

CN7 Reserved Hirose 6 ways, DF13-6PV

CN9 Panel backlight control JST 2-way, B2B-XH-A (Matching type : XHP-2)

S1 Power on/off control JST 2-way, B2B-PH-K (Matching type : PHR-2)

PP1 Main input power Molex 43650-0200 compatible

(Matching connector type : Molex 43645-0200 compatible)

(Matching power cable : P/N 426013800-3, 160mm)

PP2/PP3 Alternative power input DC power Molex 2 pin 0.156” pitch

Specifications subject to change without notice

Summary: Jumpers setting

Ref

Purpose Note

JA1 On board +5V logic power enable 1-2 & 3-4 closed, factory set, do not remove

JA2 On board +2.5V logic power enable 1-2 & 3-4 closed, factory set, do not remove

JA3 On board +1V logic power enable 1-2 & 3-4 closed, factory set, do not remove

JP1 Reserved Factory sets Open

LED1 Reserved Factory sets Open

LED2 Reserved Factory sets Open

SW2 Function selection See table 1

SW3 Panel selection See table 2

Table 1 : DIP switch selection – SW2

Pos. # Function Description

1 Input signal color bit selection OFF : 8 bit (for SVH-1920)

ON : 10 bit (for SVX-1920 (Coming soon)

2 Input LVDS display mode selection If SW2 position 1 = OFF (8 bit)

OFF : Mapping B

ON : Mapping A

If SW2 position 1 = ON (10 bit)

OFF : JEIDA mode

ON : VESA mode

3 Output LVDS display mode selection OFF : JEIDA mode

ON : VESA mode

Please adjust to get the correct picture. See as Appendix I for details of

mapping of VESA and JEIDA.

4 Motion compensation mode OFF : Enable (for film mode(a))

ON : Disable (for static text mode(b))

Remark :

(a) Film mode – Image with motion pattern

(b) Static text mode – Image with static pattern

Table 2 : DIP Switch selection – SW3

Pos #1 Pos #2 Pos #3 Pos.#4 Description Panel resolution

For WUXGA panels

OFF OFF OFF OFF LG LC370WUD-SAB1 1920x1080

ON OFF OFF OFF NEC NL192120AC25-02 1920x1200

For additional and recent added panels, see panel support table at http://www.digitalview.com/controllers/csg.php

Specifications subject to change without notice

CN1 – LVDS signal input connector: Hirose, DF13A-40DP-1.25DSA (Matching type : DF13-40DS-1.25C)

PIN SYMBOL DESCRIPTION

1 LVDS_IN_A0+ Positive differential LVDS data bit A0

2 LVDS_IN_A0- Negative differential LVDS data bit A0

3 LVDS_IN_A1+ Positive differential LVDS data bit A1

4 LVDS_IN_A1- Negative differential LVDS data bit A1

5 OP1 Reserved

6 OP2 Reserved

7 LVDS_IN_A2+ Positive differential LVDS data bit A2

8 LVDS_IN_A2- Negative differential LVDS data bit A2

9 LVDS_IN_A3+ Positive differential LVDS data bit A3

10 LVDS_IN_A3- Negative differential LVDS data bit A3

11 LVDS_IN_A4+ Positive differential LVDS data bit A4

12 LVDS_IN_A4- Negative differential LVDS data bit A4

13 LVDS_IN_AC+ Positive LVDS clock for A channel

14 LVDS_IN_AC- Negative LVDS clock for A channel

15 LVDS_IN_B4+ Positive differential LVDS data bit B4

16 LVDS_IN_B4- Negative differential LVDS data bit B4

17 LVDS_IN_B0+ Positive differential LVDS data bit B0

18 LVDS_IN_B0- Negative differential LVDS data bit B0

19 LVDS_IN_B1+ Positive differential LVDS data bit B1

20 LVDS_IN_B1- Negative differential LVDS data bit B1

21 OP3 Reserved

22 OP4 Reserved

23 LVDS_IN_B2+ Positive differential LVDS data bit B2

24 LVDS_IN_B2- Negative differential LVDS data bit B2

25 LVDS_IN_B3+ Positive differential LVDS data bit B3

26 LVDS_IN_B3- Negative differential LVDS data bit B3

27 GND Ground

28 GND Ground

29 LVDS_IN_BC+ Positive LVDS clock for B channel

30 LVDS_IN_BC- Negative LVDS clock for B channel

31 GND Ground

32 GND Ground

33 VLCD_LV Panel power supply (3,3V/5V) from front end controller

34 VLCD_LV Panel power supply (3,3V/5V) from front end controller

35 VLCD_LV Panel power supply (3,3V/5V) from front end controller

36 VLCD_LV Panel power supply (3,3V/5V) from front end controller

37 NC No connection

38 VLCD_HV Panel power supply (+12V/18V) from front end controller

39 VLCD_HV Panel power supply (+12V/18V) from front end controller

40 VLCD_HV Panel power supply (+12V/18V) from front end controller

CN2 – Additional panel power input connector : HIROSE D13-20DP-1.25 (Matching type : DF13-20DS-1.25C)

PIN SYMBOL DESCRIPTION

1 VLCD_LV Panel power supply (3,3V/5V) from front end controller

2 VLCD_LV Panel power supply (3,3V/5V) from front end controller

3 VLCD_LV Panel power supply (3,3V/5V) from front end controller

4 VLCD_LV Panel power supply (3,3V/5V) from front end controller

5 VLCD_LV Panel power supply (3,3V/5V) from front end controller

6 VLCD_LV Panel power supply (3,3V/5V) from front end controller

7 GND Ground

8 GND Ground

9 GND Ground

10 GND Ground

11 GND Ground

12 GND Ground

13 GND Ground

14 GND Ground

15 VLCD_HV Panel power supply (+12V/18V) from front end controller

16 VLCD_HV Panel power supply (+12V/18V) from front end controller

17 VLCD_HV Panel power supply (+12V/18V) from front end controller

18 VLCD_HV Panel power supply (+12V/18V) from front end controller

19 VLCD_HV Panel power supply (+12V/18V) from front end controller

20 VLCD_HV Panel power supply (+12V/18V) from front end controller

Indice

Altri manuali digitalview Hardware per computer

digitalview

digitalview HD-3000v2 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

digitalview IE-1000 Manuale utente

Manuali Hardware per computer popolari di altre marche