Digitus DA-70148-4 Manuale utente
USB 2.0 to IDE/SATA ADAPTER
User Manual
DA-70148-4
USB 2.0 adapter from Digitus is quick and easy connection without outer casing. Use
any 2.5”/3.5” IDE or SATA HDD/SSD as an additional external hard disk/SSD.
It is the ideal for service, maintenance, and trouble-free, temporary access to hard
disks, e.g. for data backups and system restores.
Characteristics
Support SATA spread-spectrum transmitter
Support SATA II Asynchronous Signal Recovery (Hot Plug) feature
Compliance with USB 2.0 (Hi-Speed USB) electrical specification
Compliance with USB Mass Storage Class Bulk-Only Transport Specification
Support:
480Mbps High Speed (HS) and 12Mbps Full Speed USB operation
ATA/ATAPI-7
ATA/ATAPI Ultra DMA Mode
ATA/ATAPI PACKET command feature set
ATA/ATAPI LBA48 addressing mode
dual LUN (Logic Unit Number) for USB to ATA/ATAPI
Windows 10, 8, 7, Vista, Windows XP, Mac OS 10.x
Product introduction
1. SATA Port for 2.5”/3.5” SATA Hard Drive
2. IDE Port for 2.5” IDE Hard Drive
3. IDE Port for 3.5” IDE Hard Drive
4. Power/Active Light: It will keep flashing when it is detecting the 2.5”/3.5” SATA Hard
Drive or during the Data transferring.
Package Content
1 x USB 2.0 - IDE/SATA Adapter
1 x IDE (4-pin Molex) cable
1 x Power Supply (12V/2A) included
1 x User manual
USB 5V ~100/230V
Tips for HDD Installation
For 2.5”/3.5” SATA HDD
(1) Have SATA Hard Drive connect with ER
(2) Have the external Power Adapter connect with USB 2.0 TO IDE/SATA ADAPTER
(3) Have USB 2.0 TO IDE/SATA ADAPTER connect with your computer, then power on,
your computer system will detect the SATA HDD.
3.5''IDE
For 3.5” IDE HDD
(1) Have the 3.5” IDE HDD connect with USB 2.0 TO IDE/SATA ADAPTER
(2) Have the external Power Adapter connect with USB 2.0 TO IDE/SATA ADAPTER.
(3) Have USB 2.0 TO IDE/SATA ADAPTER connect with your computer, then power on,
your computer system will detect the IDE HDD.
For 2.5” IDE HDD
(1) Have 2.5” IDE HDD connects with USB 2.0 TO IDE/SATA ADAPTER.
(2) Have the external Power Adapter connect with USB 2.0 TO IDE/SATA ADAPTER,
NOTES:
Our product USB 2.0 TO IDE/SATA ADAPTER can support 2.5”/3.5” SATA & IDE HDD,
please refer to the below application image.
Verification
Please track the path “My computer” and “My computer” -- > “System Properties” -- >
“Device Manager” and expand the item “Hard disk controllers”, you should meet the
following screen.
If you use an all new HDD
1) Please use “Fdisk” to set the capacity of your HDD, but this will destroy all the data in
the HDD.
2) Format your HDD by standard procedures, if you can’t find your new HDD, please
Follow the steps in FAQ-1
Note:
1. “Fdisk” or “Format” will destroy all the data and program in the HDD you select. Please
make sure there is not any data in it, or all the data have a backup copy.
2. This product can support 2 HDD/SSDs only simultaneously, and cannot support 2 IDE
HDD at the same time.
3. If the computer cannot detect the 2.5 INCH IDE HDD, please check if it’s connected with
the right direction.
FAQ
Q:
I could see the icon at the right down comer on the screen, but I still couldn’t find my external
HDD.
A:
1. Please make sure your HDD has been installed correctly.
2. Please make sure your HDD has been set in “Master” position,
3. Please make sure your HDD has been formatted. If no, please format your hard drive first.
4. If you are sure you have installed correctly all the hardware and software, please follow
the steps as below to catch your HDD.
1. Enter “Control Panel” and enter “System” icon
2. Double click it to find a “System Manager”.
3. Find a “Disk drivers” category. There should be 2 drivers, double click the HDD
4. Find the “Setting” button and choose the option “Removable Drive”
5. Your computer will automatically assign a new letter to this USB HDD after
restarting your computer
Caution
1. If you are not sure what OS you are using, please contact your PC dealer.
2. Please don’t put this USB HDD in a humid or high-temperature environment.
3. If your first installation is failed, please firstly remove the wrong device throngs the
path as below: path=Control Panel > System > System Properties > Device Manager >
Please remove the items with “?” or “!” mark.
Hereby ASSMANN Electronic GmbH, declares that this device is in compliance with the
requirements of Directive 2014/30/EU (EMC), Directive 2014/35/EU (LVD) and the Directive
2011/65/EU for RoHS compliance. The complete declaration of conformity can be requested by post
under the below mentioned manufacturer address.
Warning:
This device is a class B product. This equipment may cause some radio interference in living
environment. In this case, the user can be requested to undertake appropriate measures to prevent
interference.
www.assmann.com
ASSMANN Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany
Indice
Altri manuali Digitus Adattatore
Digitus
Digitus DA-70617 Manuale utente
Digitus
Digitus DN-70560 Manuale utente
Digitus
Digitus DN-7053 Manuale utente
Digitus
Digitus WIRELESS 300N AUTO INSTALLATION USB ADAPTER Manuale utente
Digitus
Digitus DN-10050-1 Manuale utente
Digitus
Digitus DA-70830 Manuale utente
Digitus
Digitus DA-70844 Manuale utente
Digitus
Digitus DA-70451 Manuale utente
Digitus
Digitus DN-10136 Manuale utente
Digitus
Digitus DA-70844 Manuale utente
Digitus
Digitus UNIVERSAL TRAVEL ADAPTER Manuale utente
Digitus
Digitus DN-70230 Manuale utente
Digitus
Digitus DA-70167 Manuale utente
Digitus
Digitus DN-7045 Manuale utente
Digitus
Digitus DN-10050-1 Manuale utente
Digitus
Digitus DN-95108 Manuale utente
Digitus
Digitus DN-3025 Manuale utente
Digitus
Digitus DN-70543 Manuale utente
Digitus
Digitus DN-10180 Manuale utente
Digitus
Digitus AC600 Manuale utente
