Digitus DN-10190 Manuale utente
Dual-Port 40G QSFP
Adapter
Quick Installation Guide
DN-10190
2
Table of Contents
1. Introduction ..................................................................... 2
2. Package Contents ............................................................. 3
3. Specification ..................................................................... 3
4. System Requirements ...................................................... 4
5. Hardware Installation....................................................... 5
6. Install Drivers and Software ............................................. 5
1. Introduction
The DN-10190 Dual-Port 40G QSFP adapter with PCI Express 3.0 and
x8 Mellanox Connectx-3 technic delivers high-bandwidth and
industry-leading Ethernet connectivity and is compliant with PCIe2.0
and 1.1. It features two 40 Gigabit QSFP+ Ethernet ports compliant
with QSFP+ MSA Spec Rev 1.0, and two QSFP ports supporting FDR-
14 InfiniBand or 40Gb Ethernet, with support for InfiniBand FDR
speeds of up to 56Gbps (auto-negotiation FDR-10, DDR and SDR).
The low-profile form factor adapter with 2u bracket supports virtual
protocol interconnect (VPI), InfiniBand Architecture specification
v1.2.1, IEEE Std. 802.3, copper cables and optical cables with the use
of QSFP connectors, and SFP+ cables available through QSA (Quad to
Serial). It enables low latency RDMA over 40Gb Ethernet, with legacy
and UEFI PXE network boot support, and supports iSCSI as a software
iSCSI initiator in NIC mode with NIC driver. The adapter supports
multiple operating systems, such as FreeBSD, Linux 5.x and above,
VMware, Windows server2008/2012/2016/2019, win7/ win8/
3
win8.1/ win10 32 or 64bit. It also supports CORE-Direct○,R
application off-load, GPUDirect application off-load, RDMA over
converged Ethernet (RoCE), end-to-end QoS and congestion control,
TCP/UDP/IP stateless off-load, Ethernet encapsulation (EoIB), SR-IOV
support (16 virtual functions supported by KVM and Hyper-V(OS
dependant) up to a maximum 127 virtual functions supported by the
adapter), and traffic steering across multiple cores, making it a
versatile adapter suitable for a wide range of applications.
2. Package Contents
•1x Dual-Port 40G QSFP adapter
•1x User’s Manual
•1x CD Driver
•1x Low profile bracket
3. Specification
•PCI-Express host interface specification v3.0 x8 and Complete
with PCIe2.0 and 1.1
•Two 40 Gigabit QSFP+ Ethernet ports
•Compliant with QSFP+ MSA Spec Rev 1.0
•Two QSFP ports supporting FDR-14 InfiniBand or 40Gb Ethernet.
•Support for InfiniBand FDR speeds of up to 56Gbps (auto-
negotiation FDR-10, DDR and SDR)
•Low-profile form factor adapter with 2u bracket
•Virtual protocol interconnect (VPI)
•InfiniBand Architecture specification v1.2.1 compliant
•IEEE Std. 802.3 compliant
•Compliant with copper cables and optical cables with the use of
QSFP connectors.
•Support for SFP+ cables available through QSA (Quad to Serial)
•CORE-Direct○, R application off-load.
4
•GPU Direct application off-load.
•RDMA over converged Ethernet (RoCE)
•End-to-End QoS and congestion control
•TCP/UDP/IP stateless off-load.
•Ethernet encapsulation (EoIB)
•SR-IOV support;16 virtual functions supported by KVM and
Hyper-V (OS dependant) up to a maximum 127 virtual functions
supports by the adapter.
•Enables low latency RDMA over 40GbEthernet (supported with
both non-virtualized and SR-IOV enable virtualized servers)—
latency as low as 1us.
•Traffic steering across multiple cores
•Microsoft VMQ/VMware Net Queue support
•Industry-leading throughput and latency performance
•Legacy and UEFI PXE network boot support
•Supports iSCSI as a software iSCSI initiator in NIC mode
with NIC driver.
•Supports Operation Systems: FreeBSD, Linux5.x and above,
VMware, Windows server2008/2012/2016/2019,
win7/win8/win8.1/win10 32 or 64 bit.
4. System Requirements
•FreeBSD, Linux, VMWare ESXi
•Win-server2008 R2/ Win-server2012 R2/ Win-server2016/
Win-server2019
•Windows: 7/8/8.1/10 32/64bit
•One available PCI Express x8/x16 slot
5
5. Hardware Installation
1. Turn Off the power to your computer.
2. Unplug the power cord and remove your computer’s cover.
3. Remove the slot bracket from an available PCIe x4/x8/X16 slot.
4. To install the card, carefully align the card’s bus connector with
the selected PCIe slot on the motherboard. Push the board down
firmly.
5. Replace the slot bracket’s holding screw to secure the card.
6. Replace the computer cover and reconnect the power cord.
6. Install Drivers and Software
Windows Operating Systems
You must have administrative rights to the operating system to
install the drivers.
1. insert the CD driver bound with Mellanox network driver into
your CD-ROM drive.
2. if the Found New Hardware Wizard screen is displayed,
click Cancel.
3. select a driver based on the system type:
for Windows Server type: (Assume that D):
“D:\NIC Drivers\Mellanox\ConnectionX-3\Windows Server”
for Windows type: (Assume that D):
“D:\NIC Drivers\Mellanox\ConnectionX-3\Windows Client”
4. Double click the driver corresponding to the system.
5. Follow the instructions in the install wizard to finish it.
Installing Linux Drivers from Source Code
1. Download and expand the base driver tar file.
2. Compile the driver module.
3. Install the module using the mod probe command.
4. Assign an IP address using the ipconfig command.
6
Function
controller
MELLANOX ConnectX-3
Fibre Media
10Gbase-cx4, 10Gbase-R,
and 1000Base-R, 40Gbase-R4
Fiber type
10Gbase-cx4, 10Gbase-R,
and 1000Base-R, 40Gbase-R4
Connect type
PCIE3.0 X8
Operation Systems
Windows8.1
Windows10
（
1909,1809,1607
）
Windows Server2003/2003 R2
Windows Server2008/2008 R2
Windows Server2012/R2
Windows Server2016/R2
Ubuntu 14.04 or later
Sles12 sp2 or later
REHL/CentOS7.2 or later
Oracle Linux 7.8 or later
KYLIN 10
Fedora 32
Debian 9.11/9.13/10.5/10.8
BCLINUX7.5 OR later
Stable kernel version 3.x,4.x or later
VMware ESX/ESXi 5.X,6.X or later
Port type Dual- Port 40G QSFP28 connecter
Each Port transmit
speed
1/10/40Gbps
Ethernet power
management
yes
7
standards
IEEE 802.3ae 10 GbE
IEEE 802.3ba 40 GbE (all three FDR
adapters)
IEEE 802.3ad Link Aggregation
IEEE 802.3az Energy Efficient
Ethernet
IEEE 802.1Q, .1P VLAN tags and
priority
IEEE 802.1Qbg
IEEE P802.1Qaz D0.2 Enhanced
Transmission Selection (ETS)
IEEE P802.1Qbb D1.0 Priority-based
Flow Control
IEEE 1588v2 Precision Clock
Synchronization
PXE/UEFI support
YES
ISCSI support
yes
VMDs, SR-IOV support
yes
TCP/IP Sec offload
YES
IPv4, IPv6 Support
yes
Jumbo frame size
9.6KB
Network I/O
Virtualization
VXLAN, Geneve, NVGRE, ISER, SR-IOV
Operation temperature
0
o
~55
o
C (32
o
F or 131
o
F)
Storage temperature
-40~ 70
o
C (-40
o
F or 158
o
F)
Relative humidity
20~80 non-condensing relative
humidity
MAX Power
10.13W
8
Hereby ASSMANN Electronic GmbH declares that the Declaration of
Conformity is part of the shipping content. If the Declaration of
Conformity is missing, you can request it by post under the below
mentioned manufacturer address.
www.assmann.com
Assmann
Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Digitus Adattatore
Digitus
Digitus DN-3027 Manuale utente
Digitus
Digitus DN-7042-1 Manuale utente
Digitus
Digitus DN-7053 Manuale utente
Digitus
Digitus WNP-UA300-01 Manuale utente
Digitus
Digitus DN-3025 Manuale utente
Digitus
Digitus DA-10070 Manuale utente
Digitus
Digitus DA-70840 Manuale utente
Digitus
Digitus DN-7056 Manuale utente
Digitus
Digitus DA-70854 Manuale utente
Digitus
Digitus DN-70560 Manuale utente
Digitus
Digitus DA-70841 Manuale utente
Digitus
Digitus DA-70156 Manuale utente
Digitus
Digitus DA-70148-2 Manuale utente
Digitus
Digitus DA-70844 Manuale utente
Digitus
Digitus DA-70202 Manuale utente
Digitus
Digitus DN-3028 Manuale utente
Digitus
Digitus DN-95109 Manuale utente
Digitus
Digitus DN-95132 Manuale utente
Digitus
Digitus DA-70250-1 Manuale utente
Digitus
Digitus DN-30211 Manuale utente
