Digitus DN-650102 Manuale utente
8 10/100TX + 2 10/100/1000T/100/1000 SFP
Combo with 8 PoE Injectors Industrial Switch
User Manual
DN-650102
FCC Warning
This Equipment has been tested and found to comply with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. It may cause harmful interference to radio
communications if the equipment is not installed and used in accordance
with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
Content
Introduction................................................................ 1
Features................................................................... 1
Package Contents.................................................... 2
Hardware Description ............................................... 3
Physical Dimension.................................................. 3
Front Panel .............................................................. 3
Top View .................................................................. 4
LED Indicators ......................................................... 5
Ports......................................................................... 6
Cabling..................................................................... 8
Wiring the Power Inputs......................................... 11
Wiring the Fault Alarm Contact .............................. 11
Mounting Installation .............................................. 13
DIN-Rail Mounting.................................................. 13
Wall Mount Plate Mounting .................................... 15
Hardware Installation .............................................. 16
Installation Steps.................................................... 16
Network Application................................................ 17
Troubles shooting ................................................... 19
Technical Specification........................................... 20
1
Introduction
The 8 10/100TX + 2 10/100/1000T/100/1000 SFP Combo with 8 PoE Injectors Industrial
Switch is a cost-effective solution and meets the high reliability requirements demanded
by industrial applications. Using fiber port can extend the connection distance that
increases the network elasticity and performance.
Features
System Interface/Performance
RJ-45 ports support Auto MDI/MDI-X Function
Embedded 8-port PoE Injection
SFP (Mini-GBIC) supports 100/1000 Dual Mode
Store-and-Forward Switching Architecture
Back-plane (Switching Fabric): 5.6Gbps
1Mbits Packet Buffer
8K MAC Address Table
Supports Wide Operating Temperature (-40oC ~ 75oC)
Power Supply
Redundant Power Design
Case/Installation
IP-30 Protection
DIN Rail and Wall Mount Design
Relay Alarm
Relay output for port breakdown, power fail and alarm
2
Package Contents
Please refer to the package contents list below to verify them against the checklist.
8 10/100TX + 2 10/100/1000T/100/1000 SFP Combo with 8 PoE Injectors Industrial
Switch
User manual
Pluggable Terminal Block
2 wall mount plates and 6 screws
One DIN-Rail (attached on the switch)
8 10/100TX + 2 10/100/1000T/100/1000 SFP Combo with 8 PoE Injectors Industrial Switch
User Manual block connector
WallMountPlate Screws DIN-Rail
Compare the contents of the industrial switch with the standard checklist above. If any
item is damaged or missing, please contact the local dealer for service.
3
Hardware Description
In this paragraph, the Industrial switch’s hardware spec, port, cabling information, and
wiring installation will be described.
Physical Dimension
8 10/100TX + 2 10/100/1000T/100/1000 SFP Combo with 8 PoE Injectors Industrial
Switch dimension (W x D x H) is 72mm x 105mm x 152mm
Front Panel
The Front Panel of the 8 10/100TX + 2 10/100/1000T/100/1000 SFP Combo with 8 PoE
Injectors Industrial Switch is shown as below:
Front Panel of the PoE Injectors Industrial Switch
4
Top View
The top view of the 8 10/100TX + 2 10/100/1000T/100/1000 SFP Combo with 8 PoE
Injectors Industrial Switch has one terminal block connector of two DC power inputs.
Top View of the PoE Injectors Industrial Switch
5
LED Indicators
The diagnostic LEDs located on the front panel of the industrial switch provide real-time
information of system and optional status. The following table provides the description of
the LED status and their meanings for the switch.
LED Status Meaning
PWR1
Green Power 1 is active
OFF No power inputs
PWR2
Green Power 2 is active
OFF No power inputs
Fault
Red Power input 1 or 2 is inactive
OFF Power 1 & Power 2 are both active or no power
inputs
P9, P10 (RJ-45)
Upper
LED
Green Connected to network
Blinking Networking is active
OFF Not connected to network
Lower
LED
Green The port is operating at speed of 1000M
OFF The port is disconnected or not operating at
speed of 1000M
Link/Active
(P9, P10)
Green SFP port is linking
Blinks Data is transmitting or receiving
OFF Not connected to network
P1 ~ P8
(Green)
Green Connected to network
Blinking Networking is active
6
OFF Not connected to network
P1 ~ P8
(Yellow)
Yellow Ethernet port full duplex
Blinking Collision of packet occurs
OFF Ethernet port half duplex or not connected to
network
FWD (P1 ~ P8)
Green A powered device is connected utilizing Power
over Ethernet on the port
OFF No device is connected or power forwarding fails
Ports
RJ-45 ports
The UTP (RJ-45) Fast Ethernet ports will auto-sense for 10Base-T or 100Base-TX
connections. Auto MDI/MDIX means that the switch can connect to another switch or
workstation without changing straight through or crossover cabling. See the below
figures for straight through and crossover cable schematic.
RJ-45 Pin Assignments
Pin Number Assignment
1 Tx+
2 Tx-
3 Rx+
6 Rx-
[NOTE] “+” and “-” signs represent the polarity of the wires that make up each wire pair.
All ports on this industrial switch support automatic MDI/MDI-X operation, user can use
straight-through cables (See figure below) for all network connections to PCs or servers,
or to other switches or hubs. In straight-through cable, pins 1, 2, 3, and 6, at one end of
the cable, are connected straight through to pins 1, 2, 3 and 6 at the other end of the
cable. The table below shows the 10BASE-T/100BASE-TX MDI and MDI-X port pin outs.
7
Pin MDI-X Signal Name MDI Signal Name
1 Receive Data plus (RD+) Transmit Data plus (TD+)
2 Receive Data minus (RD-) Transmit Data minus (TD-)
3 Transmit Data plus (TD+) Receive Data plus (RD+)
6 Transmit Data minus (TD-) Receive Data minus (RD-)
Straight Through Cable Schematic
Cross Over Cable Schematic
2 Mini-GBIC combo port: 2 auto-detect Giga port—UTP or fiber. The gigabit
Ethernet ports are shared with the mini-GBIC ports. UTP (Gigabit Ethernet) ports
can operate in half/full-duplex modes and work at speeds of 10/100/1000Mbps that
support auto-sensing technology to enable each port to detect the connecting speed.
The mini-GBIC port is a joint for a mini-GBIC (SFP) transceiver, so the switch can
be uplinked through fiber to another one.
Indice
Altri manuali Digitus Interruttore
Digitus
Digitus DA-70236 Manuale utente
Digitus
Digitus DS-23200 Manuale utente
Digitus
Digitus DA-70235 Manuale utente
Digitus
Digitus DN-651113 Manuale utente
Digitus
Digitus DN-651148 Manuale utente
Digitus
Digitus DS-16202-1 Manuale utente
Digitus
Digitus DS-23100-1 Manuale utente
Digitus
Digitus DC-71301 Manuale utente
Digitus
Digitus Pocket USB KVM switch Manuale utente
Digitus
Digitus DN-95315 Manuale utente
Digitus
Digitus DN-95330-1 Manuale utente
Digitus
Digitus DS-44100 Manuale utente
Digitus
Digitus DS-12890 Manuale utente
Digitus
Digitus DS-12820 Manuale utente
Digitus
Digitus DA-70251 Manuale utente
Digitus
Digitus DN-80202 Manuale utente
Digitus
Digitus KC-221 Manuale utente
Digitus
Digitus DN-651160 Manuale utente
Digitus
Digitus DS-12404 Manuale utente
Digitus
Digitus DN-95347 Manuale utente
