Digitus DN-95357 Manuale utente
8+2 Port
Gigabit PoE Switch
Quick Installation Guide
DN-95357
2
Table of Contents
1. Introduction ............................................................................3
2. Main Features .........................................................................3
3. Package Contents ....................................................................3
4. Product Specification...............................................................4
5. Hardware Description..............................................................5
3
1. Introduction
DN-95357 has a CCTV function for 250 meters of ultra-long-distance
transmission. Users can choose to turn on or off the CCTV function.
Improve network security and restrain network storms, facilitate
management and maintenance, and meet the networking and access
requirements of enterprises, communities, hotels. office networks,
and campus networks.
2. Main Features
•Support IEEE802.3 at standard, compatible with IEEE802.3 af by
electrical equipment (PD)
•Stand-up output power up to 30W
•Support IEEE802.3 x full duplex flow control and Backpressure
half duplex flow control
•Panel lights to monitor working state and help fault analysis
•Perfect security mechanism
•Line-speed forwarding intelligent identification
•Support CCTV Function
•Support Energy-Efficient Ethernet (EEE) function (IEEE802.3az)
•Support PD-ALIVE function
3. Package Contents
•PoE Switch
•
User Guide
•Power Cord
4
4. Product Specification
Technical
Interface
10
＊
10/100/1000Mbps
auto-negotiation RJ45 port
PoE port
1 ~ 8
PoE stand
IEEE802.3af/at
PoE total
60 W
Power supply
65 W
Key function
CCTV
PoE port output
Max 30W
RJ45 PoE power supply
Mode A, Anode 1/2,
Cathode 3/6
Indicator
PWR (Green), LNK/ACT (Green)
PoE (Orange)
Network media
10 BASE-T: UTP category 3,4,5
cable (≤100m),
100 BASE-TX: UTP category 5,
5e cable (≤100m),
1000 BASE-T: UTP category 5,
5e cable (≤100m)
MAC Address Table
2K, Automatic study,
automatic updates
Jumbo frame
9216 Bytes
Packet buffer
2Mbit
Transfer Mode
Store-and-forward
Packet Forward Speed
14.88Mpps
Bandwidth
20Gbps
Device Dimension
168 x 93 x 32mm
Green energy saving
Support IEEE (802.3az)
Mains input
100 ~ 240V AC, 50/60Hz
5
Operating Temperature
0°C ~ 40 °C
Storage Temperature
-40 °C ~ 70 °C
Operating Humidity
10% ~ 90% non-condensing
Storage Humidity
5% ~ 90% non-condensing
Surge Protection
Common mode ± 2KV,
differential mode ± 1KV
MTBF
>50000 hour
Electrostatic standard
Contact ±6KV, air ± 8KV
5. Hardware Description
Front Panel
The Front Panel Consists of Ethernet Ports. The LED indicators are
also located on the panel.
DIP Switch: The DIP switch located on the right of the panel.
Default: the factory default mode, can normal communication
between port 1~10.
CCTV mode: 1-8 port can be isolated each other, but 1-8
port can connect to 9, 10 port after open CCTV to stop broadcast
storm to increase forwarding rate of frame. The CCTV mode, up to
250m PoE distance allows you to expand you network via Ethernet
cable to where there is no power line or outlet but where you want
to fix device such as IP Cameras.
6
Note: After change the mode, there is no need to restart manually to
make the corresponding configuration take effect.
LED indicator
LED Color Function
PWR Green
Off: No Power supply.
Light: Indicates the switch has power.
LNK/
ACT
Green
Off: No device is connected to the
corresponding port.
Light: Indicates the link through that port is
successfully established at 10/100Mbps.
Blink: Indicates that the Switch is actively
sending or receiving data over that port.
PoE Orange
Off: No PoE powered device (PD)
connected.
Light: There is a PoE PD connected to be
port, which supply power successfully.
Blink: Indicates port abnormal power
supply.
7
Rear Panel
The rear panel of the PoE Switch indicates an AC inlet power socket,
which accepts input power from 100 to 240V AC, 50/60HZ.
Power socket
Connect the female connector of the power cord here, and the male
connector to the AC (Alternating Current) power outlet. Please make
sure the voltage of the power supply meets the requirement of the
input voltage.
Grounding column
The switch already comes with lightning protection mechanism. You
can also ground the switch through the PE (Protecting Earth) cable of
AC cord or with Ground Cable.
8
Installation the Switch
This part describes how to install your Ethernet Switch and make
connections to it. Please follow the following instructions in avoid of
incorrect installation causing device damage and security threat.
•Before cleaning the switch, unplug the power plug of the switch
first. Do not clean the switch with wet cloth or liquid;
•Do not place the switch near water or any damp area. Prevent
water or moisture from entering the switch chassis;
•Do not place the switch on an unstable case or desk. The switch
might be damaged severely in case of a fall;
•Ensure proper ventilation of the equipment room and keep the
ventilation vents of the switch free of obstruction;
•Make sure that the operating voltage is the same one labeled on
the switch;
•To avoid the danger of electric shock, do not open the chassis
without authorization;
9
Desktop Installation
Install the Switch on a desktop, please attach these cushioning
rubber feet provided on the bottom at each corner of the Switch in
case of the external vibration. Allow adequate space for ventilation
between the device and the objects around it.
10
Wall-mounted installation
In the first two fixed screw on the wall as shown in the figure below. Aim
at the two fixed hole switches (M4 screw, nut diameter 7mm) and the
machine smoothly on the screw.
Turn on the switch
Please connect the AC power cord into the rear of the switch and to
an electrical outlet (preferably one that is grounded). When the
switch is power on, the LED indicators flash momentarily for one
second, which represents a resetting of the system. The Power LED
indicator turns on green.
Note: Please confirm the voltage is correct before power on,
otherwise the switch will be damaged.
(The power input is: 100V-240Vac, 50/60Hz)
Indice
Altri manuali Digitus Interruttore
Digitus
Digitus DN-95358 Manuale utente
Digitus
Digitus DN-95340 Manuale utente
Digitus
Digitus DS-13202 Manuale utente
Digitus
Digitus DA-70235 Manuale utente
Digitus
Digitus DN-80115 Manuale utente
Digitus
Digitus DN-95639 Manuale utente
Digitus
Digitus DS-12870 Manuale utente
Digitus
Digitus DN-95330-1 Manuale utente
Digitus
Digitus DS-12890 Manuale utente
Digitus
Digitus Professional DN-60013 Manuale utente
Digitus
Digitus DC OC-12 Manuale utente
Digitus
Digitus DS-12800 Manuale utente
Digitus
Digitus DN-80111 Manuale utente
Digitus
Digitus DS-11900 Manuale utente
Digitus
Digitus DA-70886 Manuale utente
Digitus
Digitus DA-70242-1 Manuale utente
Digitus
Digitus DS-45339 Manuale utente
Digitus
Digitus DS-45341 Manuale utente
Digitus
Digitus DA-70217 Manuale utente
Digitus
Digitus DS-12883 Manuale utente
