DINKING DK3300i Manuale utente
INVERTER GENERATOR
User's Manual
Kindly Remind: Please read this User's Manual carefully before using, to
operate it under the premise of ensuring the safety and environmental
protection!
Thank you very much for choosing generator set product manufactured by our
Company!
This Manual will instruct you how to operate and use the generator set safely and
properly. Please be sure to read it carefully before using.
All technical data and diagrammatic presentations in this User's Manual are
consistent with the latest product at the time of publication.
Due to the revision and other changes, contents of this Manual may be slightly
different from actual situation. The Company is entitled to revise it at any time,
and the revised version will be developed without prior notice, please understand
that. The copyright of this User's Manual belongs to the Company, and this
Manual is not allowed to be reproduced without written consent of the Company,
violators must be prosecuted.
This Manual is a permanent part of the generator set.If the generator set is resold,
the Manual will be resold together with the generator set.
Table of Contents
Safety Warning …………………………………………………………..…. 1
I. Safety Instructions ……………………………………………………….. 2
II. Names of Components …………………………………………………. 3
III. Control Functions ………………………………………………….…… 5
IV. Preparations ………………………………………………………..…… 8
V. Starting up the Generator ………………………………………………10
VI. Shutting Down the Generator …………………………………………10
VII. Using the Generator ………………………………………………..… 11
VIII. Service and Maintenance …………………………………….………16
IX. Storage and Transport…………………………………………….…… 22
X. Troubleshooting …………………………………………………….…… 23
XI. Technical Parameters………………………………………………..…24
XII. Circuit Diagram …………………………………………………………25
XIII. Rules for Three Guarantees …………………….……………........ 26
1
Safety Warning
Personal and property safeties of you and others are very vital. Please read the
Safety Warning in the User's Manual and the decals ofthe generator set carefully.
The Safety Warning can alert you to those potential hazards that could harm you
and others. In front of each SafetyWarning, there is one of four words "DANGER",
"WARNING", "ATTENTION", and "CAREFUL". Details are as follows:
DANGER Failure to follow the instruction will result in being in peril of your life
or extremely serious injury.
WARNING Failure to follow the instruction will result in being in peril of your life
or very serious injury.
CAREFUL Failure to follow the instruction will result in minor injury.
ATTENTION Failure to follow the instruction will result in the damage to your
generator set and other properties.
2
I. Safety Instructions
Before operating the generator, it will help you avoid accidents to read and
understand the Manual and familiarize yourself with the safe operation
procedures of the generator.
3
II. Names of Components
Lifting handle Knob
Leftenclosure
Fuel tank cap
Control panel
Startup handle
Spark plug cover plate
Side shield of
muffler
Right enclosure
Air filter cover
plate
Oil cover plate
Muffler
4
Control Panel
①②③④⑤⑥⑦
①Idle switch
②Oil alarm indicator
③Overload indicator
④AC output indicator
⑤DC cigarette lighter
socket
⑥AC resume switch
⑦AC socket
⑧DC socket
⑨USB socket
⑩DC protection
Earthing terminal
Three-in-one
combination switch
⑩ ⑨
⑧
5
III. Control Functions
（1）Three-in-one combination switch (hereinafter referred to as
combination switch)
①Engine and fuel switch: Ignition circuit is off and the fuel switch is off, the
engine will be unable to run.
②Engine, fuel switch and choke valve switch: Ignition circuit is in working
status, fuel switch is on and the choke valve is in fully opening status, the
engine can run normally.
③Engine, fuel switch and choke valve
switch: Ignition circuit is in working status,
fuel switch is on and choke valve is in closing
status, the engine can run normally.
ATTENTION The engine is hot, it does not need to switch off the
choke switch.
（2）Oil indicator (red)
When the oil in the crankcase drops below
safety line, oil protection system will
automatically shut down the engine, and oil
alarm indicator lights up; the engine can be
restarted up only after the oil is filled to oil level.
Tip: In the case of flame-out of the engine or being unable tobe started up,
turn the combination switch to "RUN" position, and then pull startup handle.
If oil indicator flashes a few seconds, the oil volume is insufficient, fill oil
and restart it.
（3）Overload indicator (red)
When the overload indicator lights up, the generator has detected that the
output of connected electrical equipment has been overloaded, causing
frequency converter to be overheated or AC voltage to rise. At this moment,
AC protector works and stops generating, to protect the generator and
6
ON
OFF
DC protection
connected electrical equipment. AC indicator (green) is off and overload
indicator (red) lights up, but the engine will not stop running.
When overload indicator is on and the generator has no output, please take
following counter measures:
①Switch off electrical equipment connected, and shut down the generator.
②Reduce total power of electrical equipment connected to the range of
rated output.
③Check whether there is any foreign matter blocking in cooling air inlet,
and whether there is any abnormality in related control components. If there
is any problem, eliminate it immediately.
④After checking, restart the engine.
Tip: When using electrical equipment with high starting current (such as
compressors, submersible pump, etc.), the overload indicator may start to
light up for a few seconds at the beginning, but this is not the failure
mentioned earlier.
（4）AC indicator (green)
The AC indicator lights when the engine is started and output normally.
（5）DC protection
When electronic equipment connected to DC of the generator is running, if
current is beyond rated current, DC switch automatically switches off to "OFF"
position. When operating the generator again, please press DC switch to "ON"
position.
1）“ON” DC normal outputs.
2）"OFF" DC does not output.
ATTENTION If DC protection is in off status, reduce the load of
electronic device connected to rated output range of the generator. If DC
protection is still in off status, please stop using electrical equipment directly
and consult your dealer.
7
AC recovery
（6）Energy-saving switch
1) "ON"
When energy-saving switch is switched to
"ON" position, the device controls engine
speed based on the load connected, thus very
good fuel consumption and low noise can be
obtained.
2) "OFF"
When the energy-saving switch is set to the "OFF" position, the engine will
run at rated speed, regardless of whether being connected to a load.
Tip:When using following devices, such as air compressor and submersible
pump, the energy-saving switch must be in "OFF" position, because it
requires great startup current.
（7）Fuel tank cap
Remove fuel cap by unscrewing it counterclockwise.
（8）AC recovery
When the output is overloaded, the generator will protect automatically to
output no voltage. Reduce the load, press the AC recovery switch, and the
generator will resume output.
（9）Grounding terminal
Grounding terminal shall be connected to grounding wire to prevent electric
shock. When an electrical equipment is grounded, the generator must be
grounded.
Indice
Altri manuali DINKING Generatore portatile
