Dish Network 20.1 Manuale utente
Remote User Guide
Safety Instructions
You must keep safety in mind while using this device. Keep
these and any other instructions for future reference.
Observe Warnings: Carefully follow all warnings on the device
and in the operating instructions.
Heat: Do NOT place the device near heat sources such as
radiators, stoves, heat registers, or other appliances that
produce heat.
Care and Use
Cleaning: Do NOT use liquid, abrasive, solvent, or aerosol
cleaners. Use a damp cloth for cleaning.
When Not in Use: Remove the batteries if this device is to be
left unattended or unused for a long period of time.
Refer servicing to qualied personnel when a
solid object or liquid has fallen onto or into the
device.
Do NOT attempt to service this device. Refer all
servicing to qualied personnel. Opening covers
other than the battery cover will void the warranty.
Publishing Information
Copyright © 2011. EchoStar Technologies L.L.C., Englewood,
Colorado 80112. All rights reserved.
The information in this User Guide may change without notice.
Revisions may be issued to tell you about such changes.
Send comments or questions about this User Guide to
techpubs@echostar.com or
Technical Publications, EchoStar Technologies L.L.C,
90 Inverness Drive Circle East, Englewood, Colorado 80112.
Document Number: 180532
Printed in
DISH Network is a registered trademark of
DISH Network L.L.C.
All product names, trade names, or corporate names
mentioned in this User Guide are acknowledged to be the
proprietary property of the registered owners.
1
Conguring the 20.1 Remote
Conguring the 21.1 Remote
The 20.1 remote does not require any
conguration. Go to Insert the Batteries (page 2).
1
2
3
4
Pull the remote battery cover off.
Decide whether to use IR or UHF
signals for the remote. Use UHF
signals if you do not have a clear
line of sight between the remote
and the receiver.
Set UHF/IR SWITCH to either
UHF or IR. If your remote has a
blank, black key, continue to
Insert the Batteries on page 2.
If your remote shows a “1” or a
“2” on the bottom, you can pull
out this key and ip it to the other
number (2 to 1 and 1 to 2). To
separate the key from the remote,
insert your thumbnail or a coin in
the crease. Remove the key by
grasping at the bottom.
Insert the key you wish to use to
designate the remote and slide
into place. Usually a 1 = TV1 and
a 2 = TV2. For remotes showing
the blank, black key, leave this
key as it is.
Complete the following
steps to congure
your remote.
2
Insert the Batteries
Pull the remote battery
cover off.
Insert 4 AAA batteries,
making sure to match the
plus (+) ends with the plus
markings on the battery
case.
Replace the remote
battery cover.
1
2
3
3
Using System Wizard
Note: Not all receivers support System Wizard. If
System Wizard does not appear, continue with page 4
or page 5 to make your remote work with your receiver.
Use System Wizard initially to set up the remote to
work with the receiver. System Wizard can also store/
restore your remote settings. Note: If your batteries are
low, replace them before beginning.
Press and hold 0 until
System Wizard message
appears. Make sure the
remote and receiver are
in line of sight.
If rst time in System
Wizard, follow
instructions provided.
When green checkmark
displays, select
Advanced to store/
restore remote settings.
Follow the on-screen
options.
Select Continue to
return to Live TV.
1
2
3
4
4
Making 20.1 and 21.1 IR
Remote Work with Receiver
Turn your receiver and
TV on, and press
SYSTEM INFO on the
front of the receiver.
Conrm that you
see the System
Info screen.
Press RECORD on
your remote. The
receiver then matches
the remote’s address.
Conrm that your remote
operates your receiver by
pressing remote buttons.
If this is not working, go
back to step 3.
1
2
3
4
1
For 20.1 and 21.1 IR
Use the following
instructions to
congure your remote
while using IR signals.
Note: Use these instructions if your receiver
does not support System Wizard.
5
Making 21.1 UHF Remote
Work with Receiver
Verify the UHF antenna
is installed on the back
of the receiver.
Turn your receiver and
TV on, and press
SYSTEM INFO on the
front of the receiver.
Conrm that you
see the System
Info screen.
Press RECORD on
your remote. The remote
address will probably
change on the screen.
Conrm that your remote
operates your receiver
by pressing remote
buttons. If this is not
working, go back to
step 4.
3
2
1
4
5
For 21.1 UHF
Use the following
instructions if you
have congured
your remote to use
UHF signals.
1
1
Note: Use these instructions if your receiver
does not support System Wizard.
6
SAT Mode
To use the features described in this section, make sure
you are in SAT mode by pressing the SAT Mode button.
Note: Some features may not be available depending on your
receiver model.
SAT
Power & TV Power
Top button turns the receiver on/off
Bottom button turns the TV on/off
Press this
button for
SAT Mode
Volume and
Mute Buttons
Control TV volume
Programming required
Recall
Return to last
TV channel viewed
Picture-In-Picture
(PIP) Buttons
Watch two separate
programs at once
(in Single Mode)
Number Buttons
Enter a channel
number or
navigate through
menus
Receiver Menu
Access receiver
features and settings
Input
Press once for Input
Press and hold
for Recover
Themes
Search for programs
using Themes
Info
Get info on programs
Search
Search for a program
Shortcut Keys
(for future use)
Digital Video
Recorder (DVR)
Buttons
Pause live TV and
play or record
programming
Format
Format the picture
to the desired width
to match the program
you are viewing System Wizard
Press and hold
to x remote
control issues
and sync data
DishHOME
Explore interactive
TV features
Arrow/Select
Buttons
Channel up/down,
navigate through
menus, and select
a desired option
View Satellite
Programming
Exit out of any
menu/guide and
return to viewing
live TV
Cancel
Return to
previous menu
or to watching a
program
Browse
See what is on
other channels
while watching TV
Program Guide
Display current and
future satellite
program listings
Page Buttons
Page up/down in
menus
7
TV Mode TV
Up/Down
Arrow Buttons
Channel up/
down on TV
Power
& TV Power
Turn the TV on/off
Volume
Control TV
volume
Press this
button for
TV Mode
Mute
Turn TV volume
on or off
Recall
Return to last
TV channel viewed
Picture-In-Picture
(PIP) Buttons
Display PIP features
on some TVs with
PIP capabilities
Number Buttons
Enter a desired
channel number
on TV
TV Menu
Access menu
features available
on some TVs
Input
Switch between
TV inputs
8
DVD Mode DVD
Power
& TV Power
Top button turns the
DVD player/VCR
power on and off
Bottom button turns
the TV on and off
Up/Down
Arrow Buttons
Channel up/
down on VCR
FWD
Forward a
videotape or DVD
Play
Play a videotape
or DVD
Number Buttons
Enter a channel
number for DVD
Pause
Pause a videotape
or DVD
Press this
button for
DVD Mode
Input
Switch VCR between
its TV & VCR mode
Back
Rewind a videotape
or reverse a DVD
Stop
Stop playing a DVD,
stop playing or
recording a
videotape
Record
Record on a
videotape
Altri manuali per 20.1
1
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Dish Network Telecomando
Dish Network
Dish Network Remote Control Manuale utente
Dish Network
Dish Network Platinum PVR Remote Control Manuale utente
Dish Network
Dish Network ViP 211 Series Manuale utente
Dish Network
Dish Network 104333 Manuale utente
Dish Network
Dish Network 40.0 Manuale utente
Dish Network
Dish Network Duo ViP 222 Manuale utente
Dish Network
Dish Network digital remote control Manuale utente
Dish Network
Dish Network 135331 Manuale utente
Dish Network
Dish Network 20.0 Manuale utente
Dish Network
Dish Network 3.1 Manuale utente
Dish Network
Dish Network 40.0 Manuale utente
Dish Network
Dish Network 167820 Manuale utente
Dish Network
Dish Network Hopper with Sling Manuale utente
Dish Network
Dish Network 301 IR 123271 Manuale utente
Dish Network
Dish Network 176842 Manuale utente
Dish Network
Dish Network 11 Scheda tecnica
Dish Network
Dish Network BASIC REMOTE Manuale utente
Dish Network
Dish Network DISHPlayer 500 Manuale utente
Dish Network
Dish Network DISHPlayer 500 7100/200 Manuale utente
Dish Network
Dish Network EZ Manuale utente
