Dish Network WALLY Manuale
SET UP YOUR
WALLY
A
STEP 1: Unpair Your Remote
If you are unable to turn on your original receiver, go to step 2.
APress the SYSTEM INFO buon
on the front panel of your original
receiver.
BLocate your remote from the
list on the right-hand side of the
screen. Then, use your remote
control to highlight the “Unpair”
opon and press the SELECT
buon.
QUICK TIP
You will not be able to use your
remote with your replacement
receiver unl you unpair it from
your original receiver.
2
STEP 2: Label and Disconnect Your Cables
ALocate the cable connected to the
“Satellite In” port and aach the
blue label to it. Then, unscrew this
cable from your Wally. Do not
unscrew it from the wall.
BDetermine the cable you are using
to receive audio/visual signal and
aach the correct label to it. Then,
unplug it from the receiver. Do not
unplug it from your TV.
• Orange label - RCA cable
• Black label - HDMI cable
3
A
STEP 2: Label and Disconnect Your Cables (Cont.)
CLocate the cable connected to the
“Ethernet” port, and aach the
yellow label to it. Then, unplug
it from the receiver. Do not
disconnect it from the wall. (You
may not have this cable.)
DDisconnect the power cord from
the original receiver and the wall.
A new power cord was shipped
with your replacement Wally.
4
STEP 3: Connect the Cables to Your Replacement Receiver
AConnect the Satellite In cable
to the “Satellite In” port on your
replacement Wally.
BConnect the RCA cables or the
HDMI cable to the corresponding
ports on your replacement Wally.
5
A
STEP 3: Connect the Cables (Cont.)
CConnect the Ethernet cable
to the “Ethernet” port on your
replacement Wally. (You may not
have this cable.)
DConnect the power cord that
came with your replacement Wally
to the “Power” port on the new
Wally.
6
STEP 4: Power Your Equipment
APlug the power cord from your
replacement Wally into a power
outlet, and ensure that your TV is
sll plugged in. Turn your TV on.
BMake sure that the Smart Card is
secured rmly in the slot on the
side of your replacement Wally.
7
A
STEP 4: Power Your Equipment (Cont.)
CTurn on your TV and you will see
a loading screen, which could last
for several minutes.
DWhen the Install Wizard screen
appears, go to step 5.
QUICK TIP If you do not see the loading screen,
press the “Source/Input” buon located
on your TV unl this screen appears.
Starng Up...
8
STEP 5: Pair Your Remote to Your Wally
APress the SAT buon on your
remote control to pair it to
your Wally. All of your previous
receiver’s recording mers and
other sengs will be restored
automacally.
BOnce your remote is paired, the
Install Wizard will proceed to the
next step automacally.
QUICK TIP
To avoid pairing your remote with mulple
receivers, ensure that you do not have any other
receivers in your home that are on the “Pair Remote
Control” step or in the “Diagnoscs” screen. 9
A
STEP 6: Set Up Text to Speech
AIf you would like to have a digital
voice read the text on screen, use
your remote control to highlight
“Connue with Text to Speech.”
Then, press SELECT.
BIf you do not want a digital voice
to read the text on screen, use
your remote control to highlight
“Next,” and press SELECT.
QUICK TIP If you do not select either opon,
the Install Wizard will automacally
advance aer 30 seconds.
10
Altri manuali per WALLY
5
Indice
Altri manuali Dish Network Ricevitore TV
Dish Network
Dish Network Wireless Joey Manuale utente
Dish Network
Dish Network Wireless Joey Manuale utente
Dish Network
Dish Network ViP 211k Manuale utente
Dish Network
Dish Network Wireless Joey Manuale utente
Dish Network
Dish Network Interactive TV Manuale utente
Dish Network
Dish Network WALLY Manuale utente
Dish Network
Dish Network Dish ViP722K Manuale utente
