DITEC DAS107PLUS Manuale utente

Sliding doors Ditec DAS107PLUS

User Manual

(Translation of the original instructions)

IP2270EN • 2020-11-10

www.ditecautomations.com

IP2270EN

Contents

Page

1. General precautions for safe use 3

2. Operation mode selectors 4

3. Access codes and flashing light COM500ES 5

4. Instructions for releasing and manually activating the door 6

5. Regular safety checks and safety accessories 7

IP2270EN

1. General precautions for safe use

• Failure to observe the information in the User Manual may

lead to personal injury or damage to the equipment.

These instructions must be kept and forwarded to all possible

future users of the system.

• The sliding door must only be used for the purpose for which

it was designed. Any other use should be considered improper

and therefore dangerous. The manufacturer cannot be held

responsible for any damage caused by improper, incorrect or

unreasonable use.

• Do not use the automation if it needs repairing or adjusting.

Disconnect the power supply when carrying out cleaning or

maintenance tasks.

• This product may be used by children over the age of 8 and by

people with reduced physical, sensorial or mental abilities, or

lack of experience or knowledge, as long as they are properly

supervised or have been instructed in the safe use of the de-

vice and the relative hazards.

• Cleaning and user maintenance shall not be made by

children without supervision.

• Do not allow children to play or stay near the sliding door.

Keep remote controls and/or any other control devices out of

the reach of children, to prevent the sliding door being acci-

dentally activated.

IP2270EN

2. Operation mode selectors

COM501MKS COM500ES COM501MHS

The door functions are set with different operation mode selectors.

The operation mode selector is available with 5 positions (plus RESET).

SYMBOL FUNCTION

OPEN

The door is permanently open. The door can be moved by hand

e.g. for window cleaning. All activation units are disconnected.

AUTO PARTIAL

Two-way traffic, AUTOPARTIAL is obtained. The door can be

opened partially with the inner and outer activation units and

with a key switch (if fitted).

AUTO

Two-way traffic, normal operation of the door. The door can

be opened with the inner and outer activation units and with

a key switch (if fitted).

EXIT

Passage from inside only. The door is normally locked if an

electromechanical locking device has been fitted. The door

can only be opened with the inner activation unit or with a key

switch (if fitted).

The door is closed and locked (if an electromechanical lock is

fitted).

The door cannot be opened with inner and outer activation units.

The door can be opened partially with a key switch (if fitted).

(*) When the mode selector is in mode the button

button can give a key impulse. The key impulse will open the

door to partial open position. There are two different ways how

the button works:

1. It is not possible to give a key impulse.

2. It is always possible to give a key impulse by pressing the

button for 2 seconds.

3. The mode selector must first be unlocked then it is pos-

sible button for 2 seconds.

IP2270EN

POWER RESET

B. RESET

A.Insert a narrow object in the small hole and push briefly.

B.By briefly pushing the dot (placed in the lower right corner)

with a narrow object; the door will return to the closed po-

sition (if not in operation mode selection “DOOR OPEN” or

if an error is present) and is then ready for normal opera-

tion.

NOTE! If monitored emergency unit is a demand, a test of the emergency unit is per-

formed when the operation mode selector is set from OFF or OPEN to any other op-

eration mode.

3. Access codes and flashing light COM500ES

COM500ES

Flashing

light

Down

There are 3 options to lock / unlock the operation mode selector. These are programmed in the

control panel and can be modified by the installer.

1The access is obtained by pushing the or for 2 seconds

2The access code is obtained by briefly pushing in turn , followed by , again

and . Entire code must be entered within 3 seconds.

3 No access code.

The different operation modes are selected by pushing the arrow symbols pointing

upwards or downwards. When a button is pushed a buzzer will sound. The present

selection is indicated by a blue light to the left of the function symbol or text.

When an arrow symbol has not been pushed for 5 seconds the access will be locked

FLASHING LIGHT

Red

• When a red light is flashing it is indicating an error in

the door operator. If the error remains after a RESET

then service is needed

Orange

• An orange light every other second indicates a status

or condition that can be cleared by the owner e.g. a

breakout door is broken out

Yellow • A yellow light every other second indicates that

maintenance is needed.

IP2270EN

4. Instructions for releasing and manually acti-

vating the door

Release all the mechanical locks before activating the automatic system.

In the event of maintenance, malfunctioning or emergency, disconnect the power sup-

ply then lower the lock release lever (if installed) and manually move the door wings to

their open position. To block the door wings again, bring the lock release lever back to

its initial position.

WARNING: only lock and release the door wings when the motor is switched off

IP2270EN

5. Regular safety checks and safety accessories

To meet the national/international requisites and avoid any malfunctioning or risk of

injury, carry out the following operations and checks at least once every 6 months (or

according to the frequency of use of the automation).

You are advised to have repairs and adjustments carried out by qualified personnel.

Disconnect the power supply [A] when carrying out cleaning or maintenance tasks.

TASK

Activate your operator and visually check, fastening and any damage of:

• operator and cover (1)

• cables

• operator mode selector (2)

• door and glass (stability)

Also inspect your operator and check visually for:

• condition of door seals and weather stripping

• condition of glazing rubbers

• proper operation; closes slowly and smoothly

Set the mode selector to DOOR CLOSED and check that the operator and

electromechanical lock (if fitted) work together. Also check that the lock really secures

the door.

Activate the manual command devices, if installed. Approach the door and check it

opens correctly via the automatic command devices (3).

Check the safety sensors [3-4] by standing in the path of the opening/closing door and

activating the automation.

As it opens and closes, the door must not hit the person carrying out the check

If problems occurs contact the DITEC Customer Technical Service.

CLOSEOPEN

EXIT PARTIAL

AUTO

4A 1 3 3

ASSA ABLOY Entrance Systems AB

Lodjursgatan 10

SE-261 44, Landskrona

Sweden

IP2270EN

All rights related to this material are the exclusive property of Entrematic Group AB.

Although the contents of this publication have been compiled with the greatest possible care, Entrematic

Group AB cannot accept liability for any damage that might arise from errors or omissions in this publication.

We reserve the right to make modifications without prior notice.

No part of this publication may be copied, scanned, adapted or modified without prior permission in writing

from Entrematic Group AB.

The crossed-out wheeled bin symbol indicates that the product should be disposed of separately from

household waste. The product should be handed in for recycling in accordance with local environmental

regulations for waste disposal. By separating a marked item from household waste, you will help reduce

the volume of waste sent to incinerators or landfill and minimize any potential negative impact on human health

and the environment.

Altri manuali per DAS107PLUS

Indice

Altri manuali DITEC Sistema di apertura della porta

Manuali Sistema di apertura della porta popolari di altre marche

Pamex

Pamex KT-INP35 Manuale utente

Label

Label NEPTIS/LE Manuale utente

Cal-Royal

Cal-Royal N-F77CVR Manuale utente

Scrigno

Scrigno OPEN1000 Manuale utente

TriMark

TriMark UM 34 Manuale utente

BFT

BFT WIND RMB 130B 200 Manuale utente

Alecto

Alecto ADI-250 Manuale utente

Besam

Besam Swingmaster MP Guida

CRL

CRL SENIOR PRIMA Manuale utente

Assa Abloy

Assa Abloy SARGENT 1431 Series Manuale utente

GAL

GAL MOVFR Scheda tecnica

Olide

Olide 120B Manuale utente

Normstahl

Normstahl IDO7 Manuale utente

Häfele

Häfele Finetta T 70 VF Manuale utente

AGS

AGS D-PL Manuale

Stanley

Stanley MA900ñ Istruzioni per l'installazione

WITTUR

WITTUR Hydra Plus UD300 Manuale

Alutech

Alutech TR-3019-230E-ICU Istruzioni per l'installazione e il funzionamento