dji Datalink Pro Manuale utente
DATALINK PRO
2016.06
V1.0
Quick Start Guide
快速入门指南
快速入門指南
クイックスタートガイド
빠른시작가이드
Kurzanleitung
Guía de inicio rápido
Guide de démarrage rapide
Guida di avvio rapido
Snelstartgids
Guia de início rápido
Краткое руководство пользователя
www.dji.com/product/datalink-pro
Download the latest version from
Important notes are indicated by this symbol.
重要注意事项说明符号
重要備註說明符號。
この記号は、重要な注意事項を表します。
중요 참고에는 이 기호가 표시됩니다.
Wichtige Hinweise sind durch dieses Symbol gekennzeichnet.
Las notas importantes se indican con este símbolo.
Les remarques importantes sont indiquées par ce symbole.
Le note importanti sono contrassegnate da questo simbolo.
Belangrijke opmerkingen worden aangeduid met dit symbool.
As notas importantes são indicadas por este símbolo.
Важные примечания обозначаются этим символом.
您可以在 DJI 官方网站查询最新版本
您可至下列網址下載最新版本
から最新バージョンをダウンロードしてください
최신 버전은 다음 웹 사이트에서 다운로드하십시오 .
Die aktuelle Fassung nden Sie unter
Téléchargez la dernière version à l'adresse
Scaricare l'ultima versione dal sito
Descargue la última versión en
Загрузите последнюю версию с сайта
Download de nieuwste versie op
Transra a versão mais recente disponível em
EN
2
© 2016 DJI All Rights Reserved.
Disclaimer
Thank you for purchasing the DATALINK PRO (hereinafter referred to as
“product”). Read this disclaimer carefully before using this product. By using
this product, you hereby agree to this disclaimer and signify that you have
read it fully. Please install and use this product in strict accordance with this
manual. SZ DJI Technology Co., Ltd. and its aliated companies assume
no liability for damage(s) or injuries incurred directly or indirectly from using,
installing or retting this product improperly, including but not limited to using
non-designated accessories.
DJITM is a trademark of SZ DJI Technology Co., Ltd. (abbreviated as “DJI”)
and its aliated companies. Names of products, brands, etc., appearing
in this manual are trademarks or registered trademarks of their respective
owner companies.
This product and manual are copyrighted by DJI with all rights reserved. No
part of this product or manual shall be reproduced in any form without the
prior written consent of or authorization from DJI.
This disclaimer is produced in various languages. In the event of variance
among dierent versions, the Simplied Chinese version shall prevail when the
product in question is purchased in Mainland China, and the English version
shall prevail when the product in question is purchased in any other region.
Warnings
1. Only use the DATALINK PRO in the corresponding frequency band and
in accordance with local laws and regulations.
2. Ensure all modules are connected and the parameters are set correctly
in DJI Assistant 2 when using the DATALINK PRO for the rst time.
3. DO NOT bend or fold the antennas excessively.
4. Ensure the antennas for both the Mobile Device and the Base Station
are unobstructed when used.
5. Only use the DATALINK PRO in an open environment free from radio
interference.
6. Only pair the DATALINK PRO Base Station with a Mobile Station in the
same frequency band. Note that the DATALINK PRO 400 and DATALINK
PRO 900 are not compatible.
7. When upgrading the rmware, toggle the 4-position switch to the
COMBO_SW4 position, connect the module to the PC, and then run DJI
Assistant 2.
8. To avoid interference, DO NOT use a two-way transceiver or walkie-talkie
operating near the 400 MHz band when operating the DATALINK PRO 400.
9. Only use genuine DJI parts or parts certied by DJI. Unauthorized
parts or parts from non-DJI-certied manufacturers may cause system
malfunctions and compromise safety.
10. Ensure the DATALINK PRO and its components are free from
contamination (e.g. water, oil, soil and sand).
11. Download the latest version of the user manual or software for any
related DJI product that is required when using this product.
EN
© 2016 DJI All Rights Reserved.
3
Introduction
The DATALINK PRO is used for real-time wireless data transmission, including
communication between the Base Station and the Mobile Station. There
are DATALINK PRO 400 and DATALINK PRO 900 versions to meet the
requirements of dierent regions. The multi-functional bidirectional transmission
link is perfect for the DJI A3 ight control system, D-RTK and Ground Station.
Use frequency bands near 400 MHz and 900 MHz to avoid radio interference
with the DJI Lightbridge and remote controller. Support for multiple interfaces,
such as USB, CAN and UART, oers additional connectivity.
Mobile Station
* The DATALINK PRO 400 and DATALINK PRO 900 use dierent antennas with identical
functionality. No need to install antennas for the TAIWAN version as the antennas are built-in.
Overview
Base Station
1
2
3
4
1
23
4
5
6
5
6
A
A1
C1
B1
A4
C4
B3
A3
C3
B4
A2
C2
B2
B
1. Antenna Interface
2. Working Status Indicator
3. Linking Button
4. Micro USB
5. CAN/UART Port, CAN port and UART
port can be used separately.
A. CAN port with baud rate of 1 Mbps.
A1: Power (DC 9 V input)
A2: GND
A3: CAN-H
A4: CAN-L
B. UART port with baud rate 115200 bps
supported.
B1: Power (DC 9 V input)
B2: GND
B3: UART-RX
B4: UART-TX
6. 4-position Switch
C1: UART_SW1
C2: CAN_SW2
C3: USB_SW3
C4: COMBO_SW4
1. Antenna Interface
2. Linking Button
3. Micro USB
4. CAN/UART Port (same specication
as the Base Station)
5. 4-position Switch (same specication
as the Base Station)
6. Working Status Indicator
DATALINK PRO 400 Antenna ×3 DATALINK PRO 900 Antenna ×3
8-pin Cable ×2
Double-sided tape
Micro USB Cable ×1
DATALINK PRO 400 Antenna ×1 or
or
DATALINK PRO 900 Antenna ×1
4-pin Cable ×1
Mobile Station Antenna *
Base Station Antenna*
Accessories
EN
4
© 2016 DJI All Rights Reserved.
Installation and Connection
The following uses the DATALINK PRO 900, DJI Matrice 600, D-RTK and
DJI Intelligent Flight Battery to illustrate a typical installation and connection.
1. Attach the Base Station antenna. Place the Base Station on the D-RTK
Ground System’s base board, and then x it with a screw (included with
the D-RTK product). Then connect the Base Station and the D-RTK
Ground System via an 8-pin cable.
2. Install the Mobile Station to the DJI Matrice 600 with double-sided tape.
Attach the antennas to the Mobile Station and x them to the frame
arms with two clips. Then connect the Mobile Station and the D-RTK Air
System via an 8-pin cable.
• Refer to the “D-RTK User Manual” for details if using the D-RTK.
Usage
Use the DATALINK PRO in an open environment free from radio interference.
The DATALINK PRO can work in Full Duplex Mode, Broadcast Mode and
Ground Station Mode as described below:
1. Full Duplex Mode: Toggle the 4-position switch to the UART_SW1,
CAN_SW2 or USB_SW3 position. This is useful for point-to-point
communications.
2. Broadcast Mode: Toggle the 4-position switch to the UART_SW1, CAN_
SW2 or USB_SW3 position. This is useful for point to multi-point (up to
32) transmissions.
3. Ground Station Mode: Be sure to toggle the 4-position switch to the
COMBO_SW4 position when using the DJI Ground Station. The DJI
Ground Station supports up to ve Air Systems. (Refer to www.dji.com
to learn more, as the number varies according to region.)
EN
© 2016 DJI All Rights Reserved.
5
• Power cycle the DATALINK PRO, Flight Control System and
D-RTK after upgrading.
• DJI Assistant 2 supports Windows 7 (or later) or Mac OS X 10.9 (or
later).
• Full Duplex Mode and Broadcast Mode can be turned on or o in
DJI Assistant 2.
• Be sure to toggle the 4-position switch to the UART_SW1
position if using the D-RTK and working in Full Duplex Mode or
Broadcast Mode, otherwise the D-RTK may fail to receive data
from the DATALINK PRO.
Linking Procedures
The Base Station and Mobile Station come already linked out of the box.
Note that frequency linking is required if any device is changed or added.
1. Enable the D-RTK Ground System’s battery to power on the DATALINK
PRO Base Station.
2. Hold the Base Station’s Linking Button for about 3 seconds to enter
Linking mode. The Working Status LED will blink red and green
alternatively.
3. Enable the D-RTK Ground System’s battery to power on the DATALINK
PRO Mobile Station.
4. Hold the Mobile Station’s Linking Button for about 3 seconds and wait
for linking.
5. The Base Station and Mobile Station will exit Linking mode and connect
with each other if successfully linked.
6. Follow linking procedures 2-5 to link other Mobile Stations one by one
when setting up a single-to-multiple system.
Conguring Parameters with DJI Assistant 2
1. Download DJI Assistant 2 from www.dji.com and install it on your computer.
2. Toggle the 4-position switch to the COMBO_SW4 position, connect the
Base Station to the computer with DJI Assistant 2 running, and then
congure parameters according to the message prompts.
3. Congure the Mobile Station in the same way. If multiple Mobile Stations
are used, you must congure each Mobile Station one by one.
EN
6
© 2016 DJI All Rights Reserved.
• Refer to the “DJI Ground Station User Manual” for details if using
the DJI Ground Station.
LED Description
—
Solid White Device is initializing, only displays when
powering on.
—
Solid Red
Base Station: All Mobile Stations are
disconnected in Full Duplex Mode.
Mobile Station: All Mobile Stations are
disconnected in both Full Duplex Mode
and Broadcast Mode.
—
Solid Green
Base Station: At least one Mobile Station
connected to the Base Station in Full
Duplex Mode.
Mobile Station: Mobile Station connected
correctly in Full Duplex Mode.
Using the DJI Ground Station
The A3 Flight Control System and DATALINK PRO are required when using
the DJI Ground Station Mode. Ensure they are connected correctly before
powering on.
1. Download DJI Ground Station from www.dji.com and install it on your
computer, and then run the Ground Station software.
2. Toggle the 4-position switch on the Base Station to the COMBO_SW4
position, and connect the Base Station to the PC via a Micro USB cable.
3. Toggle the 4-position switch on the Mobile Station(s) to the COMBO_
SW4 position and connect the D-RTK Air System’s CAN1 port to the A3
Flight Control System‘s CAN1 port via a 4-pin CAN cable.
4. Enable the D-RTK Ground System’s battery to power on the DATALINK
PRO Base Station rst and wait until the Working Status LED turns solid
green.
5. Enable the D-RTK Air System’s battery to power on the DATALINK PRO
Mobile Station.
CAN1
Working Status LED
EN
© 2016 DJI All Rights Reserved.
7
—
Solid Blue
Base Station: Working in Broadcast Mode.
Mobile Station: Working in Broadcast Mode
and receiving the data from Base Station.
......
Blinking Blue
and Purple
Alternately
Working in Ground Station Mode.
......
Blinking Red
and Green
Alternately
Linking in progress.
...... Blinking Purple Connected to the Assistant successfully.
...... Blinking Yellow Upgrading or preparing for upgrade.
Blinking Yellow
Twice 4-position switch is toggled successfully.
......
Quickly Blinking
Green
Current system setting is saved (Run mode
changed successfully), or connected device
information is clear.
...... Blinking Red
Parameter error after powering on. If not
resolved by power cycling, contact your
dealer.
Type DATALINK PRO 400 DATALINK PRO 900
Performance
Transmission Power
Mainland China:
10dBm
Taiwan, China:
10dBm
South Korea:
10dBm
CE:
FCC:
Canada:
Australia:
Japan:
13dBm
27dBm
27dBm
27dBm
10dBm
Power Consumption
Base Station:
2.1 W
Mobile Station:
0.65 W
Base Station:
1.2 W
Mobile Station:
0.65 W
Features
Frequency Band (MHz)
Mainland China:
430-432
Taiwan, China:
429.175-429.2375
South Korea:
447.8625-447.9875
CE:
FCC:
Canada:
Australia:
Japan:
869.525
903-925.5
903-925.5
916.5-925.5
923.1-926.3
Serial Data Rate 115200 bps
Antenna Options Vertically polarized
Supported Interfaces USB, UART, CAN
Supported Max. Mobile
Station Number
Full Duplex Mode: 1
Broadcast Mode: 32
Ground Station Mode: Up to 5*
Supported DJI Products A3, D-RTK, Ground Station
Operating Temperature 32° to 113°F (0° to 45°C)
Storage Temperature -40° to 185°F (-40° to 85°C)
Humidity 5% to 95%, non-condensing
Dimension
(without Antenna)
Base Station:
82.9 mm × 51 mm × 14.35 mm
Mobile Station:
57.8 mm × 42.3 mm × 9.35 mm
Specications
EN
* Refer to www.dji.com to learn more, as the number varies according to region.
Weight
(without Antenna)
Base Station: 53 g
Mobile Station: 25.5 g
Power Supply
Voltage Base Station: DC 9 V
Mobile Station: DC 9 V
Max. Current
(Transmitting Signal) 230 mA 130 mA
Max. Current
(Receiving Signal) 70 mA
Copyright © 2016 DJI All Rights Reserved.
This content is subject to change.
Download the latest version from
www.dji.com/support
Altri manuali per Datalink Pro
2
Indice
Lingue:
Altri manuali dji Trasmettitore
dji
dji LIGHTBRIDGE Manuale utente
dji
dji Transmission High-Bright Monitor Combo Manuale utente
dji
dji Video Transmitter Manuale utente
dji
dji O3 Air Unit Manuale utente
dji
dji Datalink Pro Manuale utente
dji
dji OT-213 Manuale utente
dji
dji OT-213 Manuale utente
dji
dji Datalink Pro Manuale utente
dji
dji LIGHTBRIDGE 2 Manuale utente
dji
dji SRW-60G Manuale utente
