DMP Electronics Thinline 7060 Manuale utente
INSTALLATION GUIDE
Thinline™ LCD Keypads
Models 7060, 7063, 7070, 7073
Aqualite™ LCD Keypads
Models 7060A, 7063A, 7070A, 7073A
Security Command™ LCD Keypads
690/690F, 790/790F, 693/793
LCD Keypad Installation Guide 1
© 2006 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
LCD Keypad Installation Guide 1
DMP Keypads
The DMP Thinline™, Aqualite™, and Security Command™ LCD Keypads offer
exible features and functionality in stylish design choices.
32-Character Display
Armed LED
Power LED
Data Entry Digit keys
COMMAND Key
Back Arrow Key
Select Keys
1 2 3 4
9 0 CMD
5 6 7 8
ABC PRINTING
F R I 2 : 51 AM
Thinline™/Aqualite™ Keypad
�
Security Command™ Keypad
Each keypad provides four 2-button Panic keys, AC power LED, Armed LED,
32-character display, backlit keyboard with easy-to-read lettering and an
internal speaker. The logo on Thinline and Aqualite keypads is also backlit.
The Models 7070/7070A, 7073/7073A, 790/790F, and 793 keypads provide four
fully programmable Class B, Style A protection zones you can program for a
variety of burglary and access control applications.
The Model 7063/7063A, 7073/7073A, and 693/793 keypads provide a built-in
proximity card reader designed to read HID proximity credentials. The Model
7073/7073A and 793 keypads provide a door strike relay and allow Wiegand
input from HID, DMP, or other external card readers.
2 LCD Keypad Installation Guide
LCD Keypad Installation Guide 3
Installing the Keypad
All DMP keypad housings are designed to easily install on any 4” square box,
3-gang switch box, DMP 695 and 696 backbox, or a at surface. Figure 1 shows
the keypad housing base mounting hole locations.
Remove the Cover
The keypad housing is made up of two parts: the front, which contains the
circuit board and keyboard components and the base. Use the following steps
and gures to separate the keypad front and base.
1. Insert a at screwdriver into
one of the slots on the bottom
of the keypad and gently lift the
screwdriver handle toward you
while pulling the halves apart.
Repeat with the other slot.
2. Using your hands, gently separate
the front from the base and set
the front and components aside.
Harness Wiring
Figure 1 shows wiring harness assignments. Observe wire colors when
connecting the red, yellow, green, and black wires to the keypad bus. When
wiring directly to the panel terminals, connect red to panel terminal 7, yellow
to terminal 8, green to 9, and black to panel terminal 10. Use 1k Ohm EOL
resistors, DMP Model 311, on keypad zones 1 through 4.
The 7060/7060A, 7063/7063A, 690/690F, and 693 keypads are supplied with a
4-wire harness for panel keypad bus connection.
The 7070/7070A, 7073/7073A, 790/790F, and 793 keypads are supplied with a
12-wire data bus/zone harness. Four wires connect to the keypad bus. The
remaining eight wires are for the four zone inputs: two wires for each zone.
The 7073/7073A and 793 keypads are also supplied with one 5-wire output/
reader harness.
Lift screwdriver
handle up
toward you to
separate keypad
cover from base.
Thinline
or
Aqualite
Keypad
Building Wall
Lift screwdriver
handle up
toward you to
separate keypad
cover from base.
Building Wall
Security
Command
Keypads
2 LCD Keypad Installation Guide
LCD Keypad Installation Guide 3
Surface and Backbox
Mounting Holes
Combined 4-square
and 3-gang switch box
Mounting Holes
Keypad Back
Surface and Backbox
Mounting Holes
1K EOL
1K EOL
1K EOL
1K EOL
Green/White – Connect Reader Data 0
White – Connect Reader Data 1
Orange – Door Strike Normally Open
Gray – Door Strike Common
Violet – Door Strike Normally Closed
Yellow/White
White/Yellow
Orange White
White/Orange
Red/White
White/Red
Brown/White
White/Brown
Black – Ground
Green – Receive Data
Yellow – Send Data
Red – Keypad Power
– Zone 4
– Zone 3
– Zone 2
– Zone 1
External
Reader/
Door Strike
7073/7073A,
793 Keypads
Zones
1 through 4
7070/7070A,
7073/7073A,
790/790F, and
793 Keypads
All Keypads
Figure 1: Keypad Back Showing Wiring Harness Assignments
4 LCD Keypad Installation Guide
LCD Keypad Installation Guide 5
Additional Power Supply
If the current draw for all keypads exceeds the panel output, you can provide
additional current by adding a Model 505-12 auxiliary power supply. Connect
all keypad black ground wires to the power supply negative terminal. Run a
jumper wire from the power supply negative terminal to the panel common
ground terminal. Connect all keypad power (+12 VDC) wires to the power
supply positive terminal. Do NOT connect the power supply positive terminal
to any panel terminal. Refer to the 505-12 Power Supply Installation Guide
(LT-0453) for more information.
Keypad Bus Monitor
For UL Listed re protective systems, the 893/893A Module must be installed in
the XR500 Series or XR200 control panel to monitor the keypad bus and sound
an audible trouble whenever the keypad bus fails to operate. Refer to the 893/
893A Module Installation Sheet (LT-0135).
Card Readers
When a proximity credential is presented to an internal or external reader, a
beep tone is heard and the Power and Armed LEDs blink. This provides both an
audible and visual acknowledgement of the credential read.
Internal Access Control Reader
The 7063/7063A, 7073/7073A, and 793 keypads provide a built-in proximity
card reader designed to read HID 1300 Series proximity credentials.
Note: For UL Listed access control applications, the keypad must be
installed within the protected area.
External Access Control Reader
To accept Wiegand data input from HID, DMP, or other external card readers,
connect a 12 VDC external reader to the 7073/7073A or 793 keypad. Connect
the Red and Black power wires from the reader to the power wires from the
panel. These connect in parallel with the keypad power wires. Connect the
Reader (Data 1) wire to the White wire on the 5-wire keypad harness. Connect
the Reader (Data 0) wire to the Green/White wire on the 5-wire keypad
harness. See Figure 2.
Door Strike Relay Specications (7073/7073A, 793 only)
The 7073/7073A and 793 keypads provide one internal Form C single pole,
double throw (SPDT) relay for controlling door strikes or magnetic locks. Three
wires on the 5-wire harness, Violet (N/C), Gray (Com), and Orange (N/O), allow
you to connect devices to the relay. The Form C relay draws up to 15mA of
current and its contacts are rated for 1 Amp at 30 VDC maximum.
4 LCD Keypad Installation Guide
LCD Keypad Installation Guide 5
1K EOL
1K EOL
1K EOL
1K EOL
Green/White – Connect Reader Data 0
White – Connect Reader Data 1
Orange – Door Strike Normally Open
Gray – Door Strike Common
Violet – Door Strike Normally Closed
Yellow/White
White/Yellow
Orange White
White/Orange
Red/White
White/Red
Brown/White
White/Brown
Black – Ground
Green – Receive Data
Yellow – Send Data
Red – Keypad Power
– Zone 4
– Zone 3 Request to Exit (option)
– Zone 2 Door Contact (option)
– Zone 1 7/0 Panic (option)
To Keypad Bus
External Card
Reader
Figure 2: 12 VDC Reader Wiring for 7073/7073A and 793 Keypads
Wiring the 333 Suppressor
One Model 333 Suppressor is included with the 7073/7073A and 793 keypads.
Refer to Figure 3 and install the suppressor across the 5-wire output/reader
harness Common (C) and Normally Open (N/O) or Normally Closed (N/C). If
the device being controlled by the relay is connected to the N/O and C wires,
install the suppressor on the N/O and C wires. If the device is connected to the
N/C and C wires, install the 333 Suppressor on N/C and C wires.
Door Strike Relay
Operation
As soon as the user code sent
from the reader is veried by
the panel, the keypad door
strike relay activates for 5
seconds. During this time,
the access door connected
to Zone 2 must be opened
to start the programmed
entry/exit timer and zone
Soft-Shunt.
Note: The 5-second door strike is programmable in the panel when the keypad
is used on an XR200-485, XR500 Series, or XR2500F panel. Refer to the XR500
Series Program Guide (LT-0679) or the XR200-485 Program Guide (LT-0196).
Figure 3: 5-wire Harness/Suppressor Installation
6 LCD Keypad Installation Guide
LCD Keypad Installation Guide 7
Zone 2 Door Contact with Soft-Shunt™
(7073/7073A, 793 only)
If the door being released by the keypad is protected, you can provide a
programmed shunt time by connecting its contact to Zone 2 (White/Red pair)
on the keypad and enabling the Soft-Shunt feature. See ZONE 2 SHUNT later in
this document. Door contacts may be N/C or N/O.
Note: The Door Strike time is programmable when the keypad is used on
an XR200-485, XR500 Series, or XR2500F panel. Refer to the XR500 Series
Programming Guide (LT-0679) or the XR200-485 Programming Guide (LT-0196).
Zone 3 Request to Exit (7073/7073A, 793 only)
You can also connect a normally open PIR (or other motion sensing device)
or a mechanical switch to Zone 3 (White/Orange pair) on the keypad to
provide a request to exit capability to the system. See ZONE 3 EXIT later
in this document. When Zone 3 shorts, the keypad relay activates for 5
seconds. During this time, the user can open the protected door to start the
programmed Soft-Shunt entry/exit timer. If the door is not opened within 5
seconds, the relay restores the door to its locked state.
Note: A Zone 3 Request to Exit is inhibited for 3 seconds after the keypad reads
a card and a door strike occurs. This is to allow entry to the area and pass
under a Request-to-Exit PIR.
Panic Key Options
2-Button Panic Keys
All keypads offer a Panic key function that allows users to send Panic,
Emergency, or Fire reports to the central station. In order to use the Panic
keys, you must enable the Panic key
function in the keypad user menu.
See Programming Instructions later
in this document when enabled. The
Panic key function activates as soon
as you apply power to the keypad.
Install the supplied icon labels below
the top row of Select keys as shown in Figure 4.
The user must press and hold the two Select keys for two seconds until a beep
from the keypad is heard. At the beep, the panel sends the following zone
alarm reports to the central station:
Panic (left two Select keys)—Zone 19 + Device Address
Emergency—non-medical (center two Select keys)—Zone 29 + Device Address
Fire (right two Select keys)—Zone 39 + Device Address
Figure 4: Panic Key Label Placement
6 LCD Keypad Installation Guide
LCD Keypad Installation Guide 7
7/0 Panic Keys
All keypads also allow the user to initiate an optional Panic alarm by pressing
the 7 and 0 (zero) keys simultaneously for one-half (1/2) second. You must
enable the 7/0 Panic function in Installer Options in order to use the 7/0 Panic
keys. See Programming Instructions later in this document. When enabled,
all keypads send a Zone Short message to the panel for the rst zone of the
keypad address. When the keys are released a Zone Restore message can be
sent from the initiating keypad.
To produce a panic alarm, program the rst zone of the keypad address as a
panic type in panel programming. Place a 1k Ohm end-of-line (EOL) resistor,
DMP Model 311, across the White/Brown pair of zone wires on models 7070/
7070A, 7073/7073A, 790/790F and 793. This allows a Zone Restore message to
be sent when the keys are released. The 1k Ohm EOL resistor is not required
on 7060/7060A, 7063/7063A, or 690/690F keypads.
Internal Speaker Operation
All keypads emit standard tones for key presses, entry delay, and system alerts.
The speaker also provides distinct burglary, re, zone monitor, and prewarn
cadences. The keypads provide an alternate prewarn with alarm cadence that
occurs when the status list displays a zone alarm.
Backlighting
On Thinline and Aqualite keypads, both the logo and keyboard light when a key
is pressed or the speaker sounds.
On Security Command keypads, only the keyboard lights when a key is pressed
or the speaker sounds. The backlighting dims to medium brightness whenever
the speaker is on.
During an alarm condition, all lighted areas turn Red. When all alarm
conditions are cleared from the display, the Red display turns off and the
lighted areas return to the user-selected brightness.
End-User Options
All keypads provide three keypad adjustments the end-user can make through
a User Options Menu. The user can also view the keypad model number and
address in User Options.
8 LCD Keypad Installation Guide
LCD Keypad Installation Guide 9
On all keypads press and hold the Back Arrow (<—) and CMD (COMMAND) keys
for two seconds to access User Options. The keypad display changes to SET
BRIGHTNESS. Use the COMMAND key to display the next Option or press the
Back Arrow to exit the User Options function.
SET BRIGHTNESS
< >
Backlighting Brightness
Set the keypad LCD Display brightness level, Power
and Armed LEDs, and the Green keyboard and logo
backlighting. Use the left Select key to lower the
keyboard and logo brightness and the right Select
key to raise the brightness. If the brightness
level is lowered, it reverts to maximum intensity
whenever a key is pressed. If no keys are pressed,
and the speaker has not sounded for 30 seconds,
the user-selected brightness level restores.
SET TONE
< >
Internal Speaker Tone
Set the keypad internal speaker tone. At the SET
TONE display, use the left Select key to lower the
tone and the right Select key to raise the tone.
SET VOLUME LEVEL
< >
Internal Volume Level
Set the keypad internal speaker volume level
for key presses and entry delay tone conditions.
During alarm and trouble conditions, the volume is
always at maximum level. Use the left Select key
to decrease the keypad volume and the right Select
key to increase the volume. Press the COMMAND
key to display the Model Number.
MODEL NUMBER
7073 V303 030805
Model Number
The LCD displays the keypad model number and
the keypad rmware version and date. The user
cannot change this information in User Options.
KEYPAD ADDRESS
01
Keypad Address
The LCD displays the current keypad address.
While in User Options, the user cannot change the
keypad address. Press the Back Arrow key to exit
the User Options function.
Altri manuali per Thinline 7060
3
Questo manuale è adatto per i seguenti modelli
13
Indice
Altri manuali DMP Electronics Tastiera
DMP Electronics
DMP Electronics 9800 Series Manuale utente
DMP Electronics
DMP Electronics Thinline Series Guida all'installazione
DMP Electronics
DMP Electronics Security Command 670 Manuale utente
DMP Electronics
DMP Electronics XTL Series Manuale utente
DMP Electronics
DMP Electronics 9800 Series Guida all'installazione
DMP Electronics
DMP Electronics 9000 Series Guida all'installazione
DMP Electronics
DMP Electronics Thinline 7463 Guida all'installazione
DMP Electronics
DMP Electronics Thinline Series Manuale utente
DMP Electronics
DMP Electronics 9863 Manuale utente
DMP Electronics
DMP Electronics XR5FC Manuale utente
DMP Electronics
DMP Electronics 7800 Series Guida all'installazione
DMP Electronics
DMP Electronics 691 Manuale utente
DMP Electronics
DMP Electronics Security Command 670-A Manuale utente
DMP Electronics
DMP Electronics Security Command 690 Manuale utente
DMP Electronics
DMP Electronics 9800 Series Guida all'installazione
DMP Electronics
DMP Electronics 7000INT Series Guida all'installazione
DMP Electronics
DMP Electronics Thinline 7060 Manuale utente
DMP Electronics
DMP Electronics 7800 Series Guida all'installazione
DMP Electronics
DMP Electronics Thinline Series Guida all'installazione
DMP Electronics
DMP Electronics 9000 Series Manuale utente
