DMP Electronics Thinline Series Manuale utente

InstallatIon GuIde

7360/7363 Thinline Series Icon Keypads

Description

The DMP Thinline™ Series Icon Keypads offer exible features and functionality in a stylish design. The 7300 Series

provides an easy to understand icon display to assist users when arming and disarming the system or using any of the

standard system features. The icons provide immediate

recognition of any system alarm as well as system status.

The Model 7360 provides three 2-button Panic keys, backlit

keyboard with easy-to-read lettering and an internal speaker.

The Thinline logo is also backlit.

Card Reader

The Model 7363 also provides a built-in proximity reader

designed to read standard HID proximity credentials. When a

proximity credential is presented to the internal reader, a beep

tone is heard to provide an audible acknowledgement of the

credential read.

Proximity Credentials Compatibility

DMP Keypads with internal proximity readers are compatible

with most standard 125Khz Prox credentials available from

HID and all DMP proximity credentials. DMP Keypads are not compatible with iClass or other non-HID credentials. There

are custom and non-standard credentials from HID that are not compatible with DMP proximity keypads. When using HID

cards that have not been purchased directly from DMP, thoroughly test the application fully before

installation. DMP does not guarantee compatibility with credentials not purchased from DMP.

Installing the Keypad

All DMP keypad housings are designed to easily install on any 4” square box, 3-gang switch box,

DMP 695 and 696 backbox, or at surface. Figure 1 shows the keypad housing base mounting hole

locations.

Remove the Cover

The keypad housing is made up of two parts: the front, which contains the circuit board and keyboard

components and the base. Use the following steps to separate the keypad front and base.

1. Insert a at screwdriver into one of the slots on the bottom of the keypad and gently lift the

screwdriver handle toward you while pulling the halves apart. Repeat with the other slot.

2. Using your hands, gently separate the front from the base and set the front and components aside.

Harness Wiring

Figure 1 shows wiring harness assignments.

Observe wire colors when connecting the Red,

Yellow, Green and Black wires to the keypad

bus. When wiring directly to the panel terminals,

connect Red to panel terminal 7, Yellow to terminal

8, Green to 9 and Black to panel terminal 10. The

7360 and 7363 keypads are supplied with a 4-wire

harness for panel keypad bus connection. Since

all 7300 Series keypads operate together on the

Keypad bus using the same address, there is no

address option to set.

System Information Pull-Out Card

Included with the Icon keypad is a System

Information Pull-Out Card. User Code instructions

are on one side and the opposite side offers an

area to record zone numbers and names. Figure 1

shows the location of the pull-out card holder on

the back of the keypad. When inserting the System

Information Card while the keypad is attached to the

wall, rst insert the bottom of the card at an angle

to align the card into the bottom slot, then slide the card in place.

Lift screwdriver

handle up

toward you to

separate keypad

cover from base.

Thinline

Keypad

Building Wall

Thinline™ Series Icon Keypad

Icon Display

Shortcut and Digit keys

Backlit Logo

and Proximity

Antenna COMMAND Key

Back Arrow Key

Select Keys

Surface and Backbox

Mounting Holes

Combined 4-square and 3-gang

switch box Mounting Holes

Keypad Back

Black – Ground

Green – Receive Data

Yellow – Send Data

Red – Keypad Power

Guide Tabs

Reference Card

Figure 1: Keypad Back with Wiring Harness

Digital Monitoring Products Thinline™ Series Icon LCD Installation Guide

Additional Power Supply

If the current draw for all keypads exceeds the panel output, provide additional current by adding a Model 505-12 auxiliary

power supply. Connect all keypad Black ground wires to the power supply negative terminal. Run a jumper wire from the

power supply negative terminal to the panel common ground terminal. Connect all keypad power (+12 VDC) wires to the

power supply positive terminal. DO NOT connect the power supply positive terminal to any panel terminal. Refer to the

505-12 Power Supply Installation Guide (LT-0453) for more information.

Panic Key Options

2-Button Panic Keys

All keypads offer a panic key function that allows users to send Panic, Emergency, or Fire reports to the central station.

In order to use the panic keys, enable the functions in the keypad user menu. See Programming Keypad Options later in

this document. Install the supplied icon labels below the top row of Select keys as shown in Figure 2.

Press and hold the two Select keys for two seconds until a beep from the

keypad is heard. At the beep, the panel sends the following zone alarm

reports to the central station. Note: All 7300 keypads send address 8 as a

default on panic alarms.

Panic (left two Select keys)—Zone 19

Emergency—non-medical (center two Select keys)—Zone 29

Fire (right two Select keys)—Zone 39

Internal Speaker Operation

All keypads emit standard tones for key presses, entry delay and system alerts. The speaker also provides distinct

burglary, re, zone monitor and prewarn cadences. The keypads provide an alternate prewarn with alarm cadence that

occurs when the status list displays a zone alarm.

Backlighting

On Thinline Icon keypads, both the logo and keyboard light when a key is pressed or the speaker sounds.

During an alarm condition, the keyboard and logo backlight turns Red. When all alarm conditions are cleared from the

display, the Red display turns off and the lighted areas return to the user-selected brightness.

End-User Options

All models provide three keypad adjustments the end-user can make through the User Options Menu.

Press and hold the Back Arrow (<—) and CMD (COMMAND) keys for two seconds to access User Options. Use the COMMAND

key to display the next option or press the Back Arrow to exit the User Options menu.

Backlighting Brightness (b 8)

Set the keypad LCD Display brightness level and the keyboard and logo backlighting by selecting

the desired brightness from the range of off (0) to maximum (8). The far left position displays b

(Brightness) and the far right position displays the selected brightness level. If the brightness level is

lowered, it reverts to maximum intensity whenever a key is pressed. If no keys are pressed and the

speaker has not sounded for 30 seconds, the user-selected brightness level restores. The default shown

is 8.

Internal Speaker Tone (S 5)

Set the keypad internal speaker tone from the range of 1-8. The far left position displays S (Speaker)

and the far right position displays the selected tone level. The default shown is 5.

Internal Volume Level (L 8)

Set the keypad internal speaker volume level for key presses and entry delay tone conditions from

the range of off (0) to maximum (8). The far left position displays L (Level) and the far right position

displays the selected volume level. During alarm and trouble conditions, the volume reverts to

maximum level. The default shown is 8.

Software Version (100)

The LCD displays the 3-digit software version of the keypad. Version 100 is shown in the example.

Keypad Model Number

The LCD displays the model number of the keypad.

(60) The Model 7360 keypad

(63) The Model 7363 keypad with built-in proximity reader

Top Row Select Keys

Police Emergency Fire

Label shows Icons only

Figure 2: Panic Key Label Placement

Thinline™ Series Icon LCD Installation Guide Digital Monitoring Products

Installer Options Menu

All models provide a Keypad Option and Diagnostic menu to allow installing and service technicians to congure and test

keypad operation. Since all 7300 Series keypads operate together on the Keypad bus using the same address, there is no

address option to set.

Accessing Installer Options

The Installer Options Menu can only be accessed from the User Options menu while displaying the Software Version or

Model Number. When either is displayed, enter the code 3577 (INST) and press COMMAND.

Programming Keypad Options

This menu allows the top row Select keys to be enabled as 2-button Panic keys and sets the number of digits for user codes

in the system.

Panic Keys (P 0)

Use this option to congure the top two left Select keys as 2-button Panic keys. The display

shows the current panic setting. The far left position displays P (Panic) and the far right

position displays the panic key setting. To enable the panic key operation press the number

one key. This toggles between one (1) and zero (0) on the display. Zero (0) disables this

option. The default shown is 0.

Emergency Key (E 0)

Use this option to congure the top two middle Select keys as 2-button Emergency keys. The

display shows the current emergency key setting. The far left position displays E (Emergency)

and the far right position displays the emergency key setting. To enable the emergency key

operation press the number one key. This toggles between one (1) and zero (0) on the display.

Zero (0) disables this option. The default shown is 0.

Fire Key (F 0)

Use this option to congure the top two right Select keys as 2-button Fire keys. The display

shows the current re key setting. The far left position displays F (Fire) and the far right

position displays the re key setting. To enable the re key operation press the number one

key. This toggles between one (1) and zero (0) on the display. Zero (0) disables this option.

The default shown is 0.

Number of User Code Digits (U 4) from Proximity Card Read (7363)

The 7363 keypad will convert proximity credential data into a four, ve or six digit code which

is then sent to the control panel. Enter the user code digit length used by the panel. The far

left digit displays U (User Code) and the far right position displays the user code digit length.

The default shown is 4 and is the proper setting for XT30, XT50, XRSuper6, XR20 and XR40

panels.

When searching the bit string from the reader for the user code, the digits are identied and

read from left to right. When a four-digit user code is selected only the rst four digits of the

string are read.

Keypad Diagnostics

LCD Segment Test

At diagnostics startup the keyboard is backlit at maximum brightness and all the icons ash on and then off as a group.

The keypad alternates between these two states for approximately two minutes. Press the Back Arrow to return to the

Panic Keys option. Press COMMAND at any time to continue to the next test.

Test Individual Keys and Card Read

When a top row select key is pressed, the corresponding Cancel, Bypass, Extend, or Verify option is displayed. When keys

0-9 are pressed, the number of the selected key is displayed in the 3-digit display. If a proximity credential is presented

during the key test, the keypad beeps once for a successful read.

Exiting the Installer Options

Press the Command key to end Installer Options. Press the Back Arrow key to return to the LCD Segments test.

800-641-4282

www.dmp.com

Made in the USA

INTRUSION • FIRE • ACCESS • NETWORKS

2500 North Partnership Boulevard

Springfield, Missouri 65803-8877

8355

Wiring Specications for Keypad Bus

When planning a keypad bus installation, keep in mind the following specications:

1. DMP recommends using 18 or 22-gauge unshielded wire for all keypad and LX-Bus circuits. Do Not use

twisted pair or shielded wire for LX-Bus and keypad bus data circuits. To maintain auxiliary power integrity

when using 22-gauge wire do not exceed 500 feet. When using 18-gauge wire do not exceed 1,000 feet.

Install an additional power supply to increase the wire length or add devices.

2. Maximum distance for any one circuit (length of wire) is 2,500 feet regardless of the wire gauge. This

distance can be in the form of one long wire run or multiple branches with all wiring totaling no more than

2,500 feet. As wire distance from the panel increases, DC voltage on the wire decreases.

3. Maximum number of devices per 2,500 feet circuit is 40.

Note: Each panel allows a specic number of supervised keypads. However, 7300 Series keypads operate

together on a single address in an unsupervised mode.

4. Maximum voltage drop between the panel (or auxiliary power supply) and any device is 2.0 VDC. If the

voltage at any device is less than the required level, add an auxiliary power supply at the end of the circuit.

When voltage is too low, the devices cannot operate properly.

Refer to the LX-Bus/Keypad Bus Wiring Application Note (LT-2031) for more information. Also see the 710/710F Module

Installation Sheet (LT-0310).

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modications made by the user and not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Specications

Operating Voltage 12 VDC

Current Draw

7360 Normal Standby 60mA

Alarm 67mA

7363 Normal Standby 73mA

Alarm 80mA

Thinline Dimensions 7” W x 5.25” H x 0.5” D

Compatibility

XT30 and XT50 Series panels

XRSuper6, XR20 and XR40 Command Processor™

panels using Version 306 or higher.

Accessories

Proximity Credentials for use with Model 7363

1306P Prox Patch™

1306PW Prox Patch™ 26-Bit

1326 HID ProxCard II® Card

1346 HID ProxKey II® Access Device

1386 HID ISOProx II®

Backboxes

695 Keypad Conduit Backbox

696 Keypad Backbox

777 Protective Keypad Cover

Listings and Approvals

California State Fire Marshall (CSFM)

ETL: 3139201NYM

ANSI/SIA CP-01 False Alarm Reduction

ANSI/UL 1610 Central Station Burglar

ANSI/UL 609 Local Burglar

ANSI/UL 1076 Proprietary Burglar

ANSI/UL 365 Police Connected Burglar

ANSI/UL 1023 Household Burglar

ANSI/UL 985 Household Fire Warning

FCC Part 15 ID: CCKPC0086

Industry Canada ID: 5251A-PC0086

Altri manuali per Thinline Series

Questo manuale è adatto per i seguenti modelli

Altri manuali DMP Electronics Tastiera

DMP Electronics

DMP Electronics 532XR Manuale utente

DMP Electronics

DMP Electronics Thinline Series Guida all'installazione

DMP Electronics

DMP Electronics XR5FC Manuale utente

DMP Electronics

DMP Electronics 7800 Series Guida all'installazione

DMP Electronics

DMP Electronics Thinline 7463 Guida all'installazione

DMP Electronics

DMP Electronics 9800 Series Guida all'installazione

DMP Electronics

DMP Electronics Thinline 7060 Istruzioni per il montaggio

DMP Electronics

DMP Electronics Thinline 7160 Manuale utente

DMP Electronics

DMP Electronics 9800 Series Guida all'installazione

DMP Electronics

DMP Electronics 7800 Series Guida all'installazione

DMP Electronics

DMP Electronics Thinline 7060 Manuale utente

DMP Electronics

DMP Electronics 7760 Manuale utente

DMP Electronics

DMP Electronics 692 Security Command Istruzioni per il montaggio

DMP Electronics

DMP Electronics Security Command 670 Manuale utente

DMP Electronics

DMP Electronics Thinline 7060 Manuale utente

DMP Electronics

DMP Electronics 7800 Series Guida all'installazione

DMP Electronics

DMP Electronics easy entry 791 Manuale utente

DMP Electronics

DMP Electronics XTL Series Manuale utente

DMP Electronics

DMP Electronics 7872 Manuale utente

DMP Electronics

DMP Electronics Thinline Series Guida all'installazione

DMP Electronics

DMP Electronics 692F Istruzioni per il montaggio

DMP Electronics

DMP Electronics 9000 Series Manuale utente

DMP Electronics

DMP Electronics 9800INT Series Guida all'installazione

DMP Electronics

DMP Electronics 7872 Manuale utente

Manuali Tastiera popolari di altre marche

BFT

BFT SELETTO Manuale utente

Micro Id

Micro Id MP7G3BL Manuale di istruzioni

WindowMaster

WindowMaster WLI 130 Manuale utente

ACT

ACT ACT PRO 1030 Manuale utente

Cardin

Cardin SSB Series Manuale utente

Harman Kardon

Harman Kardon KP 1 Manuale utente

Chamberlain

Chamberlain KPR2000 Guida utente

CYP

CYP CR-KP1 Manuale utente

Aeware

Aeware k-35 Series Guida di riferimento

Aritech

Aritech CS-175 Series Manuale utente

GE NetworX NX-1600E Series Manuale utente

Lenze AC Tech

Lenze AC Tech MC SERIES Manuale utente

Burg Wächter

Burg Wächter secuENTRY 7711 Manuale utente

Aeware

Aeware in.k450 Manuale utente

Lenze

Lenze EPM-H410 Manuale utente

Toshiba

Toshiba RKP007Z Manuale utente

Gemini

Gemini GEM-DXK1 KEYPAD Manuale utente

Russound

Russound MDK-C5 Manuale operativo