DMP Electronics 1103 Series Manuale utente

INSTALLATION GUIDE

1103 Series

Wireless Universal Transmitter

1103 Series Installation Guide | Digital Monitoring Products 1

GET STARTED

The 1103 Series Wireless Universal Transmitters are two-way supervisory wireless transmitters typically used for

commercial ﬁre or burglary door and window applications. The 1103E features 128-bit AES encryption.

The transmitter provides a cover tamper, magnetic reed switch, and an onboard terminal block for external contact

wiring. Both sets of contacts can be programmed to operate at the same time. This allows two independent zones to

operate from one 1103.

The 1103 Series also features Disarm/Disable functionality. When this option is enabled, Zone Tripped messages are

disabled when the system is disarmed.

What’s Included

▶One 1103 Transmitter

▶One Commercial Magnet

▶One 470K EOL Resistor

▶One 3 V lithium CR123A battery

▶Hardware pack

Compatibility

▶All DMP 1100 Series Wireless Receivers

▶All DMP XT Series and XR Series panels

Note: To enable encryption on 1103E models, Version 183 is required for XT and XR Series panels and Version

300 is required for Wireless Receivers.

Procedure

To install an 1103, this guide walks you through these required steps:

1. Program the panel.

2. Install the battery.

3. Use the LED Survey to select a location.

4. Mount the transmitter.

5. Wire external contacts (optional).

6. Test the transmitter.

PCB Layout

Figure 1: 1103 Layout

External Contact

Terminal Block

Magnetic Reed Switches

Survey LED

Tamper Switch

1103 Series Installation Guide | Digital Monitoring Products 2

INSTALLATION

1 Program the Panel

Refer to the panel programming guide as needed. After completing each of the following steps, press CMD to

advance to the next prompt.

1. At a keypad, enter 6653 (PROG) to access the Programmer Menu.

2. For an 1103E, use the two steps below and then continue to step 3. Otherwise, go to step 3.

▶Go to SYSTEM OPTIONS. At 1100ENCRYPTION, select ALL to only add encrypted wireless devices

to the system. Select BOTH to allow both encrypted and non-encrypted wireless devices to be

programmed.

▶The default passphrase appears at the ENTER PASSPHRASE prompt. Press CMD to keep the default.

Press any select key or area to change the passphrase and enter an 8-character hexadecimal string

(0-9, A-F).

3. At ZONE INFORMATION, enter the wireless zone number you would like to use (must begin in the 500

range when using XR panels).

4. At *UNUSED*, enter the zone name.

5. At ZONE TYPE, press any select key or area and select the zone type.

6. At the NEXT ZN? prompt, select NO.

7. When WIRELESS? displays, select YES.

8. At SERIAL#, enter the eight-digit device serial number found on device packaging.

9. At CONTACT, select either INTERNAL or EXTERNAL. Use consecutive zone numbers if using both internal

and external contacts.

10. At SUPRVSN TIME, enter a supervision time. Default is 240.

11. At DISARM DISABLE, select NO or YES.

Note: Program the external contact ﬁrst if using both internal and external contacts with

Disarm/Disable functionality.

12. At the NEXT ZONE prompt, select YES if you are ﬁnished programming the zone. Select NO if you would

like to access additional programming options.

13. To save panel programming, go to STOP and press CMD.

2 Install the Battery

Use a 3.0V lithium battery, a DMP Model CR123A battery, or an equivalent model from Sony or Murata. For listed

installations, use either an Energizer® 123battery or a CR123A battery manufactured by Panasonic or Tekcell.

1. Push the button on the end of the transmitterand separate the two halves.

2. Observing polarity, place the battery in the holder and press it into place. Refer to Figure 1during

installation.

1103 Series Installation Guide | Digital Monitoring Products 3

Use the LED Survey to Select a Location

The 1103 Series Wireless Univeral Transmitter provides a Survey LED capability to allow one person to conﬁrm

communication with the wireless receiver or panel while the cover is removed.

1. With the cover removed, hold the transmitter in the exact desired location.

2. Press the tamper switch to send data to the panel and determine if communication is conﬁrmed or faulty.

Conﬁrmed: If communication is conﬁrmed, for each press or release of the tamper switch the LED blinks

immediately on and immediately o. Repeat this test to conﬁrm ﬁve separate consecutive LED blinks. Any

indication otherwise means proper communication has not been established.

Faulty: If communication is faulty, the LED remains on for about 8 seconds or ﬂashes multiple times in

quick succession. Relocate the transmitter until the LED conﬁrms clear communication.

Mount the Transmitter

Mount the Housing

When mounting the 1103, refer to Figure 1 and Figure 2 for

battery and mounting hole locations.

1. Remove the battery and the PCB.

2. Place the supplied #4screw into the mounting hole

and secure the transmitter to the surface.

3. Insert the included tamper screw and tamper as

shown in Figure 2.

4. Reinsert the PCB and the battery.

5. Snap the transmitter cover back onto the base.

Mount the Magnet

For magnet placement options, see Figure 4.

Commercial Installation

Place and hold the magnet cover directly on the door

closest to the magnetic reed switch, no more than 1/2”

(1.3cm) apart from the transmitter. Use the provided

#4screws to mount the magnet. See Figure 3.

Figure 2: Mounting the Transmitter

PCB Latch

Tamper

Mounting

Screws

Tamper

Screw

Figure 3: Commercial Installation

Figure 4: Placement Options

1103 Series Installation Guide | Digital Monitoring Products 4

5 Wire External Contacts (Optional)

DMP recommends using 18or 22AWG unshielded wire. It is recommended to locate a contact within 100 feet of

the transmitter. Connect the contact as normally open (N/O) or normally closed (N/C) with the 470K end-of-line

resistor. For UL listed installations, program the external contact as Normally Closed (N/C). Refer to the Contact

option under Zone Information in the appropriate panel programming guide.

If you use both the magnet reed switch in the transmitter and an external contact, use consecutive zone numbers

when connecting them to the panel.

1. Use a ﬂathead screwdriver to loosen the two screws on the external contact terminal block.

2. Insert external contact wiring into the terminal block and tighten the screws.

3. Connect the other ends of the wires to the external contact as either normally open (N/O) or normally

closed (N/C) with the included 470K end-of-line resistor.

4. Snap the transmitter cover back onto the base.

Test the Transmitter

After the transmitterhas been installed, test to conﬁrm that it is communicating reliably with the panel. Use

the Tech APP™ to perform a Wireless Check-in Test on the system or complete the following steps to perform a

Check-in Test from a keypad that is connected to the panel. At the keypad, enter 8144 (WALK) and select WLS.

Figure 5: Installing External Contacts

Parallel for N/O

Series for N/C

External Contact

Terminal Block

1103

Door

Window

External

Contact

Magnet

Program an internal

contact as the next

consecutive zone. Program an external

contact as the ﬁrst zone.

1103 Series Installation Guide | Digital Monitoring Products 5

ADDITIONAL INFORMATION

Supervision Time

When a receiver is installed, powered up, or the panel is reset, the supervision time for transmitters is reset. If the

receiver has been powered down for more than one hour, wireless transmitters may take up to an additional hour

to send a supervision message unless tripped, tampered, or powered up. This operation extends battery life for

transmitters. A missing message may display on the keypad until the transmitter sends a supervision message.

Replace the Battery

1. Push the button on the end of the transmitterand separate the two halves.

2. Remove the old battery, observe polarity, and place the new battery in the holder.

3. Snap the cover back on the transmitter.

Sensor Reset to Clear LOBAT

Once the battery is replaced, a sensor reset is required at the keypad to clear the LOBAT message. On an LCD keypad,

press and hold 2for two seconds. On a graphic touchscreen keypad, press RESET. Enter your user code, if required.

The keypad displays SENSORS OFF followed by SENSORS ON.

Compatibility

The 1103 has been designed primarily for use with the XR150/XR550 Series control panels. However, it can be used

with the XT30/XT50 or XTL Series panels as well. When used with those panels, the tamper indication is sent via

the internal contact zone only. If using the external contact, the internal contact must also be programmed in a

separate zone to provide tamper indication. In addition, the supplied magnet must be mounted next to the 1103

internal contact to restore the zone and allow the tamper switch to have priority. This issue does not exist when the

transmitter is installed with the XR150/XR550 Series panels.

1103 Series Installation Guide | Digital Monitoring Products 6

SPECIFICATIONS

Battery

Life Expectancy 5 years (normal operation)

Type 3.0V lithium CR123A

Frequency Range 905-924 MHz

Dimensions

Transmitter Case 3.3 L x 1.6 W x 1.0 H in.

Transmitter Base 3.3 L x 1.6 W x 0.1 H in.

Magnet Housing 1.5 L X 0.5 W X 0.7 H in.

Housing Material Flame retardant ABS

Encryption

▶XT and XR Series Panels Version 183 or higher

▶Wireless Receivers Version 300 or higher

CERTIFICATIONS

▶California State Fire Marshal (CSFM)

▶FCC Part 15 Registration ID CCKPC0191

▶New York City (FDNY)

▶Industry Canada Registration ID 5251A-PC0191

Underwriters Laboratory (UL) Listed

ANSI/UL 365 Police Station Connected Burglar

ANSI/UL 609 Local Burglar Alarm Units and Systems

ANSI/UL 634 Connections and Switches for use with Burglar Alarm Systems

ANSI/UL 1023 Household Burglar Alarm System Units

ANSI/UL 1076 Proprietary Burglar Alarm Units

ANSI/UL 1610 Central Station Burglar Alarm Units

ANSI/UL 864 Fire Protective Signaling Systems

Patents

▶U. S. Patent No. 7,239,236

18205

Designed, engineered, and

manufactured in Springﬁeld, MO

using U.S. and global components.

LT-0702 1.05 21373

INTRUSION • FIRE• ACCESS• NETWORKS

2500 North Partnership Boulevard

Springﬁeld, Missouri 65803-8877

800.641.4282 | DMP.com

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modiﬁcations made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada Information

This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes:

1. l’appareil ne doit pas produire de brouillage, et

2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali DMP Electronics Trasmettitore

DMP Electronics

DMP Electronics 1106 Manuale utente

DMP Electronics

DMP Electronics 1107 Manuale utente

DMP Electronics

DMP Electronics 1100INT Series Manuale utente

DMP Electronics

DMP Electronics 1140 Series Manuale utente

DMP Electronics

DMP Electronics 1144 Series Manuale utente

DMP Electronics

DMP Electronics 1142INT Manuale utente

DMP Electronics

DMP Electronics 1102 Manuale utente

DMP Electronics

DMP Electronics 1101 Series Manuale utente

DMP Electronics

DMP Electronics 1101-WINT Manuale utente

DMP Electronics

DMP Electronics 1103INT Manuale utente

DMP Electronics

DMP Electronics 1144INT Series Manuale utente

DMP Electronics

DMP Electronics 1103 Series Manuale utente

DMP Electronics

DMP Electronics 1102 Manuale utente

DMP Electronics

DMP Electronics 1142 Series Manuale utente

DMP Electronics

DMP Electronics 1101 Series Manuale utente

DMP Electronics

DMP Electronics 1139 Manuale utente

DMP Electronics

DMP Electronics 1142 Series Manuale utente

DMP Electronics

DMP Electronics 1106-WINT Manuale utente

DMP Electronics

DMP Electronics SecuraHub Series Guida all'installazione

DMP Electronics

DMP Electronics 1103INT Manuale utente

DMP Electronics

DMP Electronics 1101 Manuale utente

DMP Electronics

DMP Electronics 1100 Series Manuale utente

DMP Electronics

DMP Electronics 1141 Manuale utente

DMP Electronics

DMP Electronics 1100 Series Guida all'installazione

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente