DMR 200 Manuale utente
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•Increasetheseparationbetweentheequipmentandreceiver.
•Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
•Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
•Onlyshieldedinterfacecableshouldbeused.
Finally,anychangesormodicationstotheequipmentbytheusernotexpresslyapprovedbythegranteeor
manufacturer could void the user’s authority to operate such equipment.
UserManualv3.0.26©2011NagravisionSA.AllRightsReserved.
Inordertoprovideyouwiththebestuserexperienceavailable,therewillbe
periodicupgradestothesystemsoftware.Theexamplesandexplanationsused
whatyouwillseeonscreen.
System Software Livewire Version 3.0.26
Developed by Nagravision Consumer Electronics
This digital device has been manufactured by
Digital Multimedia Technology Co., Ltd.
Conditional Access Technology by
Under Licensing and Resale
Agreements with Nagravision
Quick Connect:
What’s in the Box
ManufacturedunderlicensefromDolbyLaboratories.Dolbyandthedouble-D
symbol are registered trademarks of Dolby Laboratories.
inthismanualaresubjecttoavailabilityandarefordemonstrationpurposesonly
and are subject to change without nofification and may not accurately represent
Smart CardDMT-200HD
All Digital Device
AC Adapter IR Extension Coaxial Cable
Mini-To-RCA
Connector
Velcro Tape
Table of Contents
1Introduction
2
Table of Contents
1.1 Front Panel 4
1.2 Rear Panel 5
1.3 Connecting Your All Digital Device 6
2.2 Getting Program Info 18
More Program Info 18
2.3 Navigating the Zap Browser 19
Browsing Channels 20
Setting a Timer 21
Exiting the Zap Browser 21
2.4 Navigating the Guide 22
The Dayshifter 23
Program Information 23
Setting a Timer 24
3.1 Main Menu 26
3.2 Favorites/Themes 27
Edit Favorites 28
3.3 Parental Controls 29
3.4 Timers 30
3.5 System Settings 31
Language Settings 31
Video Settings 31
TV Settings 32
Closed Captioning 33
PIN-Code 34
Installation 34
System Information 35
Conditional Access 35
Tuning Status 36
Reset System 36
4.1 Onscreen Help 38
Receive Channel Block and
Troubleshooting Messages Onscreen 39
4.2 Problem Solving: All Digital Device 40
Front Panel
All Digital Device
1
4
CHANNEL UP/DOWN BUTTONS
Navigates through the channel lineup
IR EXTENSION INPUT
Located on the right side
of the All Digital Device. The IR
extension input and cable are
only needed if the All Digital
Device is out of direct line of
sight of the remote control.
POWER BUTTON
Switches Power On or
into Stand-By Mode
LED
LED Lights up green when power is on.
Lights up red when in Stand-By Mode.
l
1.1 Front Panel
Rear Panel All Digital Device 1
5
SMART CARD SLOT
Insert the Smart Card into the rear
of the All Digital device. Use only the
Smart Card that was shipped in the
same carton as the All Digital Device.
Cable In
RF Input
(Coax Cable) Connects the All
Digital Device to a TV, VCR or
receiver using a coax cable.
HDMI Out
HDMI Output
(HDMI Cable) Connects All
Digital Device to a high
denition TV, VCR or receiver.
AV Out
Video Output
(Mini-to-RCA Connectors) Video
(Yellow), Right (Red) and Left
(White) connect to a TV, VCR
or receiver.
CH3/CH4
Switch
Selects TV Channel 3 or 4 as
the output channel to your TV
when the All Digital Device is
connected using a coax cable
from TV Out.
TV Out
RF Output
(Coax Cable) Connects the All
Digital Device to a TV, VCR or
receiver using a coax cable.
Power
Power Supply Connector
Connects the All Digital Device
to a power source.
1.2 Rear Panel
Connecting Your All Digital Device
All Digital Device
1
6
HDMI
AUDIO
VIDEO
CABLE N
TV INPUTS POWER OUTLET
WALL
CABLE SOURCE
C
B
A
SMART CARD
D
NOTE:
Make certain your TV is set to the proper Video
Input Mode. (Example: Video 1, Video 2)
ConnecttheAC Adaptor to the POWER input on the
All Digital Device.
Connect the AC Adaptor to a power outlet on the wall.
(Asurgeprotectedpower outlet is recommended.)
RCAConnectiontoTV
Use the Mini-to-RCA connector to connect AV OUT on the All Digital
Device to the Video (Yellow) and StereoAudio (Red and White) inputs
ontheTV.
Connectthewall cable source to CABLE IN on the All Digital Device.
ConnecttheAll Digital Device totheTV.
B
C
D
Insert the Smart Card shipped with the All Digital Device into the
rear slot, following the directions on the Smart Card.
A
AUDIO
1.3 Connecting Your All Digital Device
Connecting Your All Digital Device All Digital Device 1
7
.
HDMI
AUDIO
V DEO
CABLE IN
TV INPUTS
C
POWER OUTLET
WALL
CABLE SOURCE
B
A
D
SMART CARD
HDMIConnectiontoTV
ConnecttheAll DigitalDevice totheTV.
Use an HDMI cable (not included) to connect HDMI OUT on the
All Digital Device to the HDMI input on the TV.
C
D
Connectthewall cable source to CABLE IN on the All Digital D
evice.
ConnecttheAC Adaptor to the POWER input on the
All Digital Device.
Connect the AC Adaptor to a power outlet on the wall.
(Asurgeprotectedpower outlet is recommended.)
Insert the Smart Card shipped with the All Digital Device into the
rear slot, following the directions on the Smart Card.
A
B
WALL
Connecting Your All Digital Device
All Digital Device
1
8
.
POWER OUTLET
HDMI
AUDIO
VIDEO
CABLE N
TV INPUTS
C
WALL
CABLE SOURCE
B
A
D
SMART CARD
Connectthewall cable source to CABLE IN on the All Digital D
evice
ConnecttheAll Digital Device totheTV.
UseacoaxialcabletoconnectTV OUT onthe All Digital Deviceto
theANTjackontheTV.
CoaxialConnectiontoTV
B
C
Insert the Smart Card shipped with the All Digital Device into the
rear slot, following the directions on the Smart Card.
A
V D
T R
D
ConnecttheAC Adaptor to the POWER input on the
All Digital Device.
Connect the AC Adaptor to a power outlet on the wall.
(Asurgeprotectedpower outlet is recommended.)
Select Channel 3 or 4 on the CH3/CH4 switch, and tune to the
corresponding channel on the TV.
E
NOTE:
Use either Channel 3 or 4, whichever one is not used by a local
broadcast station. If you are uncertain, try one channel, then the
next, selecting the better/clearer option.
Indice
