Domino F Series Manuale utente
Domino F-Series
Product Manual
F720i
(2) EPT031055 Issue 2 September 2017
Note: This manual EPT031055 is intended for use only with the
F-Series product based on a BCP7 Controller.
EPT031055 Issue 2 September 2017 (3)
WARNINGS:
AS SUPPLIED, THIS CODER IS A CLASS 4 LASER PRODUCT. DURING
OPERATION, IT WILL EMIT UP TO 140 WATTS OF PULSED INVISIBLE
LASER RADIATION AT A WAVELENGTH BETWEEN 1030 AND 1120
NANOMETERS. AVOID EYE OR SKIN EXPOSURE TO DIRECT OR
SCATTERED RADIATION.
THE PRODUCTS CONTAIN EMBEDDED LASER DEVICES THAT EMIT
INVISIBLE RADIATION IN THE REGION OF 900 - 1000 NM WITH A
TOTAL OUTPUT POWER OF UP TO 140 W FOR THE RATED OUTPUT
POWER OF THE LASER MODULES: THIS RADIATION IS NOT
ACCESSIBLE TO THE USER UNLESS THE PROTECTIVE HOUSING IS
OPENED.
THE PRODUCTS CONTAIN EMBEDDED LASER DEVICES THAT EMIT
VISIBLE RADIATION IN THE REGION OF 630 - 670 NM WITH A TOTAL
OUTPUT POWER OF UP TO 5 MW FOR THE RATED OUTPUT POWER
OF THE LASER MODULES.
THE LASER MAY EMIT SIGNIFICANTLY HIGHER POWERS UNDER A
SINGLE FAULT CONDITION (<120 W 1030 – 1200 NM; <100 W 900 –
1000 NM).
THIS CODER MUST BE FITTED WITH CLASS 1 LASER GUARDING TO
SAFEGUARD AGAINST ACCIDENTAL EXPOSURE TO DIRECT OR
SCATTERED RADIATION BEFORE IT IS OPERATED OR MADE READY
FOR USE.
GUIDANCE ON CREATING AND FITTING LASER GUARDING CAN BE
FOUND IN PART 1 OF THE PRODUCT MANUAL.
USE OF CONTROLS OR ADJUSTMENTS OF PERFORMANCE OR
PROCEDURES OTHER THAN THOSE SPECIFIED IN THIS MANUAL
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
(4) EPT031055 Issue 2 September 2017
THIS PAGE INTENTIONALLY LEFT BLANK
EPT031055 Issue 2 September 2017 (5)
DOMINO F-SERIES LASER CODER
WARNING: This is a Class 4 Laser using high power invisible
infrared light. A risk of personal injury or damage
to equipment may result if proper safety
precautions are not observed. Reading and
understanding this manual is required before
operating this laser system.
This manual, Domino Part No. EPT031055, has been produced for use in
the maintenance and operation of the Domino F-Series Laser Coder, and to
reinforce and complement any training program available with the product.
It is not designed to replace any such training program.
All rights reserved. No part of this publication may be reproduced, stored
on a retrieval system, or transmitted in any form, or by any means,
electronic, mechanical, photocopying, recording or otherwise, without the
prior permission of Domino Printing Sciences plc.
Domino Printing Sciences plc has a policy of continuous product
improvement. The Company, therefore, reserves the right to modify the
specification contained in this manual without notice.
For sales and service assistance please visit the following website and
select “Contact Domino in your country” for local technical support:
http://www.domino-printing.com
© Domino Printing Sciences 2017
Note: The English version of the manual is the original version. All
other languages are translated from the English version.
Note: This manual intended use is for administrators,
technicians, installation personal and operators.
Domino Printing Sciences plc
Bar Hill
Cambridge
CB23 8TU
United Kingdom
Tel: +44 1954 782551
Fax: +44 1954 782874
(6) EPT031055 Issue 2 September 2017
CONTENTS OF THE
EC DECLARATION OF CONFORMITY
(in accordance with ISO/IEC 17050-1)
No. EPT031055/1
Issuer’s name: Domino Laser GmbH, Germany
Issuer’s Address: Fangdieckstrasse 75a, 22547 Hamburg / Germany
Object of the declaration: F-Series laser marking system consisting of:
Controller F720i (BCP7), Laser Head and optional TouchPanel.
The object of the declaration described above is in conformity with the
requirements of the following documents:
EN 61000-6-2:2005 Electromagnetic compatibility (EMC) - Part 6-2:
Generic standards - Immunity for industrial environments.
EN 60825-1:2014 Safety of Laser Products.
EN 55011:2009/A 1:2010 Industrial, scientific and medical equipment -
Radio-frequency disturbance characteristics - Limits and methods of
measurement
EN 60950-1:2006/A2:2013 Safety of Information Technology Equipment.
EN 61326-1:2013 Electrical equipment for measurement, control and
laboratory use - EMC requirements - Part 1: General requirements
EN ISO 13849-1:2008 Safety of machinery - Safety related parts of
control systems - Part 1
2014/35/EC: Low Voltage Directive
2014/30/EC: EMC Directive
2011/65/EU: RoHS2 Directive
Additional Information
Compliance is dependent upon installation and use in accordance with the
Product Manual supplied.
EPT031055 Issue 2 September 2017 (7)
(8) EPT031055 Issue 2 September 2017
CONTENTS OF THE
EU DECLARATION OF INCORPORATION
(in accordance to the Directive 2006/42/EC on Machinery appendix II I.B for
partly completed machines)
No.: EPT031055/1
Issuer‘s Name: Domino Laser GmbH
Issuer‘s Address: Fangdieckstrasse 75a, 22547 Hamburg, Germany
Person authorised to compile the relevant technical documentation,
who must be established in the Community: Research & Development
Department, Domino Laser GmbH
Object of the declaration: F-Series laser marking system consisting of:
Controller F720i (BCP7), Laser Head and optional TouchPanel.
The special technical documents corresponding to the machine have
been created according to Appendix VII, part B.
It is expressly stated that the partly completed machine fulfills all the
relevant provisions of the following EC directives.
2006/42/EU Directive 2006/42/EC of the European parliament and
of the Council of 17 May 2006 on machinery, and
amending Directive 95/16/EC (recast)
2014/35/EU Directive 2006/95/EC of the European parliament and
of the Council of 12 December 2006 on the
harmonisation of the laws of Member States relating
to electrical equipment designed for use within certain
voltage limits
2014/30/EU Directive 2004/108/EC of the European parliament
and of the Council of 15 December 2004 on the
approximation of the laws of the Member States
relating to electromagnetic compatibility
and repealing Directive 89/336/EEC
2011/65/EU Directive 2011/65/EU of the European parliament and
of the Council of 8 June 2011 on the restriction of the
use of certain hazardous substances in electrical and
electronic equipment (recast)
EPT031055 Issue 2 September 2017 (9)
Published applied harmonized standards according to Article 7 (2)
Published other applied technical standards and specifications
We commit to transmit, in response to a reasoned request by the
surveillance authorities, relevant documents on the partly completed
machinery. Property rights of the manufacturer of the partly completed
machinery remain unaffected.
Important Note
The partly completed machinery must not be put into service until the
final machinery into which it is to be incorporated has been declared in
conformity with the provisions of this Directive, where appropriate.
EN 60204-1:2006-06 Safety of machinery - Electrical equipment of
machines. Part 1: General requirements.
EN 61000-6-2:2005 Electromagnetic compatibility (EMC) - Part 6-2:
Generic standards - Immunity for industrial
environments.
EN 60825-1:2014 Safety of Laser Products.
EN 55011:2009/
A1:2010
Industrial, scientific and medical equipment -
Radio-frequency disturbance characteristics -
Limits and methods of measurement
EN 60950-1:2006/
A2:2013
Safety of Information Technology Equipment.
EN 61326-1:2013 Electrical equipment for measurement, control
and laboratory use - EMC requirements - Part 1:
General requirements
EN ISO 13849-1:2008 Safety of machinery - Safety related parts of
control systems - Part 1
ÖNORM EN ISO
11252 2013 -12-01
Lasers and laser-related equipment - Laser
device - Minimum requirements for
documentation (ISO 11252:2013); German
version EN ISO 11252:2013
(10) EPT031055 Issue 2 September 2017
Altri manuali per F Series
2
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Domino Stampante
Domino
Domino G Series Manuale utente
Domino
Domino G20I Manuale utente
Domino
Domino Macrojet 2 Manuale utente
Domino
Domino C6000 plus Manuale utente
Domino
Domino D620i Blue Manuale utente
Domino
Domino G20I Manuale utente
Domino
Domino C Series Manuale utente
Domino
Domino Ax Series Manuale dell'operatore
Domino
Domino Ax Series Manuale dell'operatore
Domino
Domino G20I Manuale utente
