Dorma KTC-2 Manuale tecnico
Stand 08.02.2012 Technische Änderungen vorbehalten
Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 1 von 14
KTC-2 (MS9)
Software-Update Version 1.0.10 manual
In order to keep your door systems updated, please proceed with the following
changes.
1. Exchange CPU -Z1 (E60-0228-10) by the new one you already received.
Front view
Relay K3-K7 Terminal block –X101/-X100
Microcell Three control
unit
(N60-0685)
Module for locking device
(E60-0120)
Output module
(E60-0119)
Input module
(E60-0118)
CPU –Z1 (E60-0228-10)
Stand 08.02.2012 Technische Änderungen vorbehalten
Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 2 von 14
KTC-2 (MS9)
Rear view
Frequency converter
(N60-0402)
Mains filter (N60-0405)
Mains connection
230 V AC –X103
24 V DC power supply unit
(N60-0583)
Relay K1
(N60-0560)
Service power outlet
max. 300 W
(N60-0694)
Collector (230VAC)-X105
Potentiometer for
24V DC adjustment
Readout the parameter settings before exchanging, in order to transfer these to the
new CPU.
Stand 08.02.2012 Technische Änderungen vorbehalten
Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 3 von 14
KTC-2 (MS9)
The following chart shows the setting entries:
The standard values are shown here, they may however vary.
Parameters
Parameter
designation
Symbo
l
Description Unit Range Original
setting
Palm
Central system
Learning cycle
Original setting
Wiring
Current error
status
Error list - - - - -
Door diameter
Door diameter mm 2000 .. 6500 (system
learns
diameter)
- - C - -
#el. locking
devices
Electromechanical bolt locking
device no = 0, yes = 1
0 .. 1 0 U U - C -
Hold after stop
Time until the el. brake is
released after an Emergency
Stop
0 = brake never released, 1 - 9
= after... sec.
sec (0 .. 9) sec 1 U U - C -
#X-Pos Auto
1 - 2
Number of starting positions in
Automatic 1 or 2
2 .. 5 2 U U - C -
SlowStop canopy
SlowStop time of canopy-
integrated sensors
sec (0 .. 15) sec
16 = ∞16 U U - C -
SlowStop wing
SlowStop time of wing sensor 0.1
sec
(0 .. 15.9) sec
16.0 = ∞16.0 U U - C -
Hold after stop
Time until the door starts after a
safety stop
0.1
sec
(0 .. 9.9) sec 1.0 U U - C -
Sec. area stop
Detection range of canopy-
integrated sensor in security
area for SlowStop
mm (d * (pi/3)
.. 500) mm 700 U U - C -
Summer
configuration
Starting-positions: 0°/180° (system
reads X-
positions)
- - - - U
Starting position
Summer
Starting-positions: 90°/270° [0],
60°/240° [1]
0 .. 1 0 U U - C -
PosV after safety
stop
Time system operates in
positioning speed after leaving
the stationary position following
a safety stop
0.1
sec
(0.0 .. 2.9) sec 1.0 U U - C -
A/M lighting
Automatic/manual lighting
control
0 ... 1 0 (auto) U U - C -
FUT warm air
curtain
Follow-up time of warm air
curtain
sec 0 ... 600 10 U U - C -
Caption:
U = adjustable value
C = resettable value
- = non-adjustable value
Stand 08.02.2012 Technische Änderungen vorbehalten
Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 4 von 14
KTC-2 (MS9)
-Z1
2. Reconnect NC at OUT4 to NO at the locking module „IL1“.
OLD:
Stand 08.02.2012 Technische Änderungen vorbehalten
Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 5 von 14
KTC-2 (MS9)
-Z1
NEW:
Stand 08.02.2012 Technische Änderungen vorbehalten
Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 6 von 14
KTC-2 (MS9)
3. Please check if terminals X101:59 and 60 are connected to -IL1(see picture).
For doors with integrated sliding doors bridge –X101:+ with 60, please!
- +
Stand 08.02.2012 Technische Änderungen vorbehalten
Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 7 von 14
KTC-2 (MS9)
4. Change the following in the UPS monitoring circuit:
- New terminal strips –X105
- Additional relay K7 (230VAC-version)
Exchange the old terminal strip –X105 by the new one and install the additional relay
K7. Wiring as follows:
NEW “K7”
Stand 08.02.2012 Technische Änderungen vorbehalten
Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 8 von 14
KTC-2 (MS9)
Stand 08.02.2012 Technische Änderungen vorbehalten
Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 9 von 14
KTC-2 (MS9)
5. Carry out the wiring as follows if the door system is furnished with UPS:
If a UPS is joined up in circuit, put the inlet connector for non-heating apparatus from
–X103 into the UPS and the other 230VAC adapter cable to be connected between
UPS and control system at –X103.
Stand 08.02.2012 Technische Änderungen vorbehalten
Software-Update_Ver1010_GB.doc DORMA KT-Systeme Seite 10 von 14
KTC-2 (MS9)
6. Is the door system without UPS, please proceed with the wiring as follows:
Questo manuale è adatto per i seguenti modelli
1
