DSE DM Series Manuale utente
INSTALLATION MANUAL
DM-WFC2 / 3 WFL1 - WIFI REMOTE CONTROLS
Page:2
What have you bought
These wifi remotes are devices that can add the remote control via the internet via WiFi to any electrical
device. You can connect these remote controls to your WiFi network and then operate them as you wish
with the included app, either in local WiFi connection or through the Internet, when you are not at home.
This manual tells you how to install and configure the devices.
DSE SRL - ITALY - WWW.DSE.EU
INSTALLATION MANUAL
DM-WFC2 / 3 WFL1 - WIFI REMOTE CONTROLS
Page: 3
Electrical connection
DM-WFC2
DM-WFC2 is a switch with stable ON / OFF switching, remotely controllable via wifi. You can use it to
power any 220V electrical equipment up to 10A, such as lighting, sounders, irrigation, etc. It also has a
switch input to operate in parallel with a traditional local control. In this way you can operate the device
indifferently through the app with the wifi or with the local switch.
CONNECTION WITHOUT LOCAL SWITCH LN = Connect the
110-250V AC power supply
Loutput-Noutput = Connect the AC power supply of the device to be controlled
CONNECTION WITH LOCAL SWITCH LN = Connect the
110-250V AC power supply
Loutput-Noutput = Connect the AC power supply of the device to be controlled. This output provides the
output power voltage.
S1-S2 = Connect the local switch
Here you see the connection diagram of a lighting also controlled locally from two points with 2
diverters.
DSE SRL - ITALY - WWW.DSE.EU
INSTALLATION MANUAL
DM-WFC2 / 3 WFL1 - WIFI REMOTE CONTROLS
Page: 4
You can install the module in a junction box or directly in the 503 switch box as in this example. If you are
using a very small cassette you can remove the side flaps with the fixing holes using pliers.
USE OF LOCAL COMMAND
You will learn how to use the wifi command shortly in the app explanations. As regards the local switch,
remember that each time the switch is operated, both in opening and closing, the status of the ON / OFF
relay will change. So the switch on-off position will not always be the same. This is normal, because you
have to consider that the user can turn on the device with the wifi app and then turn it off with the local
switch, and vice versa.
DSE SRL - ITALY - WWW.DSE.EU
INSTALLATION MANUAL
DM-WFC2 / 3 WFL1 - WIFI REMOTE CONTROLS
Page: 5
Electrical connection
DM-WFC3
DM-WFC3 is a remote control for electric locks, gate openers or garage doors. It provides an impulse
contact that operates the device and also a status contact that you can optionally connect to signal to the
remote control whether the door is open or closed. You can use this remote control for all devices that
require an impulse command instead of an ON / OFF switch.
LN = Connect the 110-250V AC power supply
S1-S2 = Connects the electric lock or gate opener command (NO contact closes for 2 seconds at each
command)
S3-S4 = Connect a contact that closes when the door is closed
Terminals S1-S2 provide a 3 second pulse whenever a remote command is executed. If you have other
local buttons to control the door or gate, you can connect them in parallel on the same control terminals.
If your drive (electric lock, garage door, etc.) has a contact that closes when the door is closed, you can
connect this contact to inputs S3-S4, so our app can tell you with certainty whether the door is open or
closed.
Here is a practical connection diagram
DSE SRL - ITALY - WWW.DSE.EU
INSTALLATION MANUAL
DM-WFC2 / 3 WFL1 - WIFI REMOTE CONTROLS
Page: 6
The two terminals separated from the main terminal block are not used.
DSE SRL - ITALY - WWW.DSE.EU
INSTALLATION MANUAL
DM-WFC2 / 3 WFL1 - WIFI REMOTE CONTROLS
Page: 7
Electrical connection
DM-WFL1
DM-WFL1 is a WiFi remote-controlled E27 lamp holder. You can simply screw it between the original socket
and the bulb. It is ideal for outdoor lighting on poles.
DSE SRL - ITALY - WWW.DSE.EU
INSTALLATION MANUAL
DM-WFC2 / 3 WFL1 - WIFI REMOTE CONTROLS
Page: 8
Positioning
When choosing the installation position of the product, pay attention to these precautions
CHECK THE WIFI COVERAGE
Before placing the remote control in its final location, remember that this device must connect to your
wifi network in order to function. You should therefore check with your mobile phone that the point
where you want to put it there is good coverage of your wifi network. If you see that the signal is very
poor, you should intervene on your wifi network, perhaps enhancing it with a repeater.
Do not install the product in an area with poor wifi signal as it would then be unreliable in its operation.
NO METALLIC CONTAINERS
Be careful not to close the remote control card in a metal container as this would shield the wifi signal.
On the other hand, you can easily close the plastic cover of the junction box because it does not provide
an important shield.
DSE SRL - ITALY - WWW.DSE.EU
INSTALLATION MANUAL
DM-WFC2 / 3 WFL1 - WIFI REMOTE CONTROLS
Page: 9
Download the Smart Life app
In order to use the product with your mobile you must first connect the device to your wifi network. To do
this you need the APPSmart Lifewhich you can download for free from Google Play or Apple Store. It is a
very popular app in home automation.
WiFi connection
At the first start you have to create an account by entering a valid email address. Press CREATE A NEW
ACCOUNT and then wait for the code via email to confirm your subscription.
If you don't have an email address you can also use your phone number by pressing Use Phone Number
and get the verification code via text message
Once you have created your account, you have your own space in the cloud where you can also upload
many WiFi remotes to control different devices.
DSE SRL - ITALY - WWW.DSE.EU
INSTALLATION MANUAL
DM-WFC2 / 3 WFL1 - WIFI REMOTE CONTROLS
Page: 10
Configure the remote control
In order to use the remote control with your mobile you must first connect the device to your wifi
network. It is a very easy operation to perform, thanks to the APP you just downloaded.
Note that on the electronic board there are: 1 button
called PAIRING
1 red LED that can be seen transparently through the plastic Locate
them because you will need them in these operations
1 - Press ADD DEVICE
2 - Choose the type of device according to the following table DM-
WFC2 = SWITCH (WIFI) - Do not use the Zigbee version DM-WFC3 =
DOOR OPENER or SMART GARAGE DOOR OPENER DM-WFL1 = SWITCH
(WIFI) - Do not use the Zigbee version
DSE SRL - ITALY - WWW.DSE.EU
Altri manuali per DM Series
3
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali DSE Telecomando
