Duratech LINK Touch DLT10-RGB Manuale utente

DLT10-RGB/TW

Manual

27-06-22

(Other languages available online www.duratech.be)

Table of contents

Technical speciﬁcations

Box contents

About the LinkTouchTM

Installation instructions

Control functions: pool lights

Control functions: heat pump & pool cover

Advanced control functions: pool lights

Display: Status icons

Safety information

First use

How to use the Settings Menu

Connecting to ...

Cover operation settings

Buzzer settings

Temperature units display setting

Aux setting

Factory reset

Caring for the LinkTouchTM

Troubleshooting

Link Controller compatibility

How to upgrade the Link Controller

control board

Resetting the LinkTouchTM

Environment / disposal of old equipment

Service & warranty

Regulatory compliance

Page 3

Page 4

Page 5

Page 6

Page 7

Page 8

Page 9

Page 10-11

Page 11

Page 12

Page 13

Page 14

Page 15

Page 16

Page 17

Page 18

Page 19

Page 20

Page 21

Page 22

Page 23

Technical speciﬁcations

General speciﬁcations

Input Voltage: 5 V DC 0,5A

Interface: LoRa 868 MHz

USB-C

Ambient Air Temperature: 0°C to +40°C

Humidity 10% to 90% RH - non condensing

Ingress protection rate: IP20

IEC Protection Class: Class II

Size (in mm): 89,5 (Height)

186,5 (Width)

17,5 (Depth)

Weight: 298 g

The LinkTouchTM is the remote of your pool control system. By using the

LinkTouch, you can control the lights, the heat pump and cover of your

swimming pool. The LinkTouchTM includes an integrated Li-Ion battery which

can be charged automatically when mounted onto the wall mount.

The LinkTouchTM connects wirelessly with a compatible Link Driver, Link

Controller, Link Master and with DURA-V, DURA-Vi and DURAPRO heat pumps.

Please check our website for latest information regarding compatibility with

heat pumps

The LinkTouchTM can operate in dierent modes:

- When the LinkTouchTM is inserted in the Wall Mount, it will charge till full

battery.

- When LinkTouchTM is removed from the Wall Mount, it will work instantly

when touched.

- When the LinkTouchTM is removed from the Wall Mount and it is not

touched for 15 seconds, it will turn into “Standby mode”. In this case the

display will be o. As soon as the touch panel is touched by the user, the

display will turn on again.

- When the battery is empty, the LinkTouchTM will no longer function. To turn

on the LinkTouchTM again, it needs to be inserted into the powered wall

mount. When inserted the display will be active again and the LinkTouchTM

will start communicating with the external devices.

Box contents

About the LinkTouchTM

Installation instructions

1.5m

The LinkTouchTM is powered using the included AC power adapter and USB

power cord

1. Plug the USB power cord into the power adapter

2. Plug the other end of the USB power cord into the USB-C connector

of the wall mount.

3. Plug the power adapter in a power outlet.

4. Mount the Link Touch onto the wall mount.

ON/OFF Lights:

Press to switch all Lights ON/OFF

Colour wheel:

Slide to change colour of Pool Lights

(only DLT10-RGB)

Colour program:

Press for previous colour program.

Colour program:

Press for next colour program.

Colour temperature:

Slide to the right to adjust the pool light

from “warm white” to “cool white”

Dimming level:

Slide to the right to increase

the brightness of the Pool Lights

Control functions: pool lights

Pool water Temperature UP:

Press to increase desired temperature

Pool cover OPEN:

IN DMS MODE: Press and hold to open

te pool cover. When ﬁnger is removed

from button the cover will stop imme

diately.

NOT IN DMS MODE: Press once after

calibration and cover fully opens.

Pool cover CLOSE:

IN DMS MODE: Press and hold to close

te pool cover. When ﬁnger is removed

from button the cover will stop imme

diately.

NOT IN DMS MODE: Press once after

calibration and cover fully closes.

*Depends on DMS mode, when AUX is set to

cover.

ON/OFF heat pump:

Press to switch pool heat pump

ON/OFF

Pool water Temperature DOWN:

Press to decrease desired temperature

NOTE:

Depending on AUX MODE, in settings

COVER OPEN/CLOSE or FUNC A/B.

Control functions: heat pump & pool cover

ON/OFF Lights:

Press and hold for 1 second ON/OFF to see the

current settings.

Activate the settings menu (*),

then use left the left arrow key to return

to the previous settings menu.

Activate the settings menu (*),

then use right arrow key to select the

desired setting.

(*) Touch the display for 3 seconds to

activate the settings menu.

Advanced control functions: pool lights How to use the Settings Menu

SEC

Tap

Touch the display on the LinkTouchTM

for 3 seconds to go into the settings

menu.

Use arrow keys to select the desired

setting.

Right: Next setting

Left: To parent menu

Touch the display once to conﬁrm

the setting.

SETTINGS

1110

Battery:

Signal:

Heat pump:

Pool lights:

Relays A and B:

Pool cover:

Battery capacity

LinkTouchTM is communicating wirelessly

Pool heat pump is ON (idle)

Pool lights are connected

Relays A and B used, not the pool cover function

Pool cover is opening/closing

Pool cover is open

Pool heat pump is ON and heating/cooling

Pool lights are ON

There is an error with relays A and B (p.19)

Pool cover is closed

There is an error with the pool cover (p.19)

Pool heat pump has an error (p.19)

There is an error with the pool lights (p.19)

Battery is charging

Battery error (p.19)

Display: Status icons Safety information

Intended use

This device has been developed as a remote control for swimming pool

accessories. The LinkTouchTM should be used only for this purpose, as

described in this user guide.

Precautions for Setup

- The LinkTouchTM can only be mounted indoor. Do not mount outdoors.

- The power adapter is designed for 100 - 240V, 50/60 Hz. Verify if the

power outlet voltage is within this range before plugging in your power

adapter.

- Install the device close to an accessible power outlet. Make sure the

power/USB cable can be easily disconnected from the power outlet at

all times.

- Protect the power/USB cable and the power adapter from being strained

pinched or bucked.

- Place the power/USB cable out of walk ways to prevent tripping over

the cable.

- Use only the power adapter provided with the LinkTouchTM. Use of an

incorrect power adapter may cause overheating or ﬁre.

- Do not bend or place a heavy object on the power/USB cable as it could

damage the cable and result in risk of electric shock or ﬁre.

- Do not use the power/USB cable if damaged or frayed.

- Be sure to hold only the connector end of the power/USB cable when

disconnecting. Repeated pulling on the cable will damage the cable.

Precautions for Operation

- Protect the LinkTouchTM from moisture and do not operate if power/

USB cable or plug are defective.

- Never touch a power plug with wet hands.

- Do not place anything on top of the LinkTouchTM.

- Never spill liquid of any kind on the LinkTouchTM.

- Do not drop or hit the LinkTouchTM.

1312

Select “Pair Start”-mode from the

settings menu.

Touch the screen once to put the

LinkTouchTM in pairing mode.

Connecting to ...

This “Pairing”-mode will allow the LinkTouchTM to establish a wireless

connection with other devices such as :

- Link Controllers, Link Master, linking per functionality

lights, cover)

- The heat pump

Note : In case the Link Master is already linked with cover and lights and

heat pump, it will distribute the links to the LinkTouchTM automatically.

Make sure the LinkTouchTM is in close proximity (<2m) of the device which

you would like to pair with wirelessly. Select “Pair Start” on the LinkTouchTM.

Power on the device.

The device will be in pairing mode for about 2 minutes after switched on.

The LinkTouchTM will now be pairing with the device.

SETTINGS

Pair

start

Pairing

Cover operation settings

Go to “AUX SETTING” in the settings

menu.

Touch the screen and select “COVER”.

Go to “DEADMANSWITCH” in the

settings. Touch the screen to select

“DEADMANSWITCH ENABLED”.

There are 2 modes:

Deadman switch operation enabled:

The cover operation will run when pressing and holding the ﬁnger

on the button and will stop when releasing the ﬁnger from the button.

Deadman switch operation disabled:

The cover operation will run with a single touch of the button

and will stop when touching the button again.

SETTINGS

Aux setting

cover

SETTINGS

Aux setting

cover

SETTINGS

DeadManSwitch

enabled

Warning :

For safety reasons :

1. The cover can only be operated when the remote device is connected to the wall mount in

case the “Deadman switch” operation mode is enabled.

2. The wall mount should be installed in close proximity of the pool to make sure that when

operating the cover with the remote device, the pool is always in sight of the operator.

Note that the wall mount can only be mounted indoor. Do not mount outdoors.

3. The operator must ensure that the path for the cover is clear and nobody gets in-

jured, while operating the cover.Note that Propulsion systems cannot be

held responsible for any damage or injury during the operation of the cover.

Note that Propulsion systems cannot be held responsible for any damage or injury during the

operation of the cover.

1514

FW V2.1 Cover Calibration in combination with DLM or DLC-010

Go to “Cover settings enter” in the

settings menu touch screen to enter

SETTINGS

Cover settings

enter

Touch the screen and select “COVER

CALIBRATION START ”.

SETTINGS

Cover calibr

start

Press the on/o icon to conﬁrm the

calibration settings

Press the cover close icon on the Link

Touch for direction forward. Verify

if the cover closes when pressing

the cover close symbol. If not press

the on/o button once “direction

forward” will change to “direction

reverse” this will change the polarity.

Press the right arrow to conﬁrm and

go to the next setting.

Press the cover open logo on the Link

Touch until the cover is fully opened.

To conﬁrm and go to the next setting

press the right arrow.

Press the cover close logo until the

cover is fully closed. To conﬁrm and

go to the next setting press the right

arrow.

COVER CALIBRATION

CONFIRM ?

STORE

COVER CALIBRATION

DIRECTION

FORWARD

COVER CALIBRATION

POSITION

OPEN

COVER CALIBRATION

POSITION

Buzzer settings

Go to “BUZZER” in the settings menu.

Touch the screen to select the

required operation mode. (note that

default setting is set to “BUZZER

ENABLED”.

The buzzer sound can be set to ON or OFF. If set to ON, then the buzzer

will sound each time as conﬁrmation for touching any of the active areas

of the LinkTouchTM. The beep will also sound when the House of Duratech’s

DuraCover is in operation. In case of a third party cover, the beeping sound

will not be active.

Warning :

It is advised to set the buzzer setting to “ON”, in order to have an audio

feedback during the operation of the cover.

SETTINGS

Buzzer

Enabled

SETTINGS

Buzzer

Enabled

1716

Temperature units display setting

Go to “TEMP °C/°F” in the settings

menu.

Touch the screen to select the

required units. (note that default

setting is set to “°C”.

The temperature units on the display can be set to Celsius or Fahrenheit

SETTINGS

Temp °C/°F

°C

SETTINGS

Temp °C/°F

°C

Aux setting

NOTE:

Repeat for “AUX MODE B”

Go to “AUX SETTING” in the settings

menu.

Touch the screen to select “AUX

SETTING AUXILIARY”.

Go to “AUX MODE A” in the settings

menu.

Touch the screen to select the

required mode “TOGGLE” or “PULSE”.

This setting will allow the installer to change the cover function to an

ON/OFF function for a dierent device.

The “Aux Setting” can be set to “Cover” or “Auxiliary”.

If set to “Cover” then the LinkTouchTM is considered to control a cover system.

If set to “Auxiliary” then the LinkTouchTM will control a dierent device with the

cover buttons and the buttons will act as an “ON” and “OFF” button.

SETTINGS

Aux setting

cover

SETTINGS

Aux setting

auxiliary

SETTINGS

Aux mode A

toggle

1918

Resetting the LinkTouchTM

You can reset (=reboot) the LinkTouchTM without loosing the preferred settings.

To reset the Link touch:

Press the “Reset” button on the back of the LinkTouchTM, using a paperclip.

RESET

Factory reset

Go to “FACTORY RESET” in the

settings menu.

Touch the screen to reset the

LinkTouchTM to factory settings.

You can reset the LinkTouchTM to the factory default settings.

Resetting the LinkTouchTM reverts all settings to the factory default

settings. Any settings, including wireless connections, that have

been changed are lost.

The factory reset can be found in the setting menu.

SETTINGS

Factory reset

reset

SETTINGS

Factory reset

reset

Altri manuali per LINK Touch DLT10-RGB

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Duratech Telecomando

Duratech

Duratech Link Touch Manuale utente

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione