Duratuf MK4B Manuale utente

Quality –Built In

ASSEMBLY INSTRUCTIONS

MK4B

BASE SIZE 4210mm x 3380mm

 Drill

 Drill Bit 3.5mm

 Drill Bit 6mm (for clear roof panel only)

 Riveter

 Hammer

 Nail Punch

 Tape Measure

 Ladder or Saw stool

 Spanners x 2

 String Line

 Tin Snips

 Skillsaw and Jigsaw (for floor only)

 Masonry Drill and 10mm Masonry Bit (for Bolt Down Kit only)

 Read all instructions carefully.

 Identify all parts and check quantities against checklist.

 If you are making your own floor refer to Raised Base Plate section

now.

 Do not attempt to build your shed in high winds.

 Beware of sharp edges.

 Protect your eyes and ears.

 Use electric tools with care. Use a Safety Trip Switch.

 It is easier and quicker if this shed is erected by two people.

 Your shed must be level. Achieve this by either levelling the ground

or by using blocks.

 If you shed is to be positioned on wet or damp ground, we recom-

mend that your shed is raised up off the ground slightly.

Tools Required:

Select your site:

Safety:

Before you start:

ASSEMBLY INSTRUCTIONS

2.280m

1.890m

0.260m

0.200m

3.700m

30m

Gable End Wall Sheets

Wall Sheets

MK4 1/2 Wall Sheets

Door - Standard Security

Instruction Booklet

Jack Studs - 140 x 45mm

Jack Studs - 60 x 45mm

Hardware Pack

Centre Door Stop

Touch-up Paint & Brush

Roof Sheets

Strip Bracing

0.580m

0.603 x 0.603m

0.588 x 0.150m

0.710 x 0.240m

Fixed Window Frame

Glaze Beads

Glass

Louvre Window Frame

Glass

Over Panel

Window Hardware Pack

3.700m

1.825m

0.350m

0.900m

Roof Sheets

Flat Roof Sheet

Clear Roof Panel

Pressed Capping Sheet

Bevel Edge Support 45 x 45mm

Clear Roof Hardware Pack

Security Double Door Hardware Pack

Alarm - MA20

Shed light

Bolt Down Kit

Peg Down Kit

CONSTRUCTION DETAILS DRAWN: DWG.NO:125 © All Images protected by Copyright.

MARK 4 B KIWI GARDEN SHED DATE: 16/12/98 SHEET:6 All information remains exclusive

(4210 x 3380—14.23m³)SCALE: 1:33 A3 ISS:D property of Riverlea Group Ltd.

140 x 45 Intermediate Ridge

140 x 45 Ridge Beam

1. Bottom Side Plates x 2

2. Bottom Front/Rear Plates x 2

3. Top Side Plates x 2

4. Top Front/Rear Plates x 2

5. Studs x16

6. Ridge Beam

7. Nogs x 15

8. Jack Studs (250 x 140 x 45) x 2

9. Jack Studs (200 x 55 x 45) x 4

10. Intermediate Roof Beams x 2

11. Roof Nogs x 16

END ELEVATION SHOWING STRAP

BRACING TOP OF RIDGE BEAM TO

UNDERSIDE OF TOP SIDE PLATE

STRAP BRACING

(to all jack studs

under beams)

MULTI-GRIP FASTENERS

EACH CORNER (ALL

HOLES NAILED OFF)

DYNABOLTS OR AP-

PROVED FIXINGS 100MM

FROM OUTSIDE CORNER

THEN ON 1200 C

PRYDA STRAP

BRACING, 5 NAILS

PER END

WHERE FLOOR IS TIMBER

FRAMED, SECURE STUDS AT

EACH CORNER TO A CORNER

ANCHOR PILE WITH A 6 KN

CONNECTOR

4210

3380

70 45 45 45 70

765

765 787 787

1185 1185

1660

45 45 45 45

45 45 45 45 45

788

140 x 45 Ridge Beam

140 x 45 Intermediate Roof Beam

PLAN

400 1900

950

4210

FRONT ELEVATION

1900

3380

END ELEVATION

45 788

MK4B TIMBER FRAME

Step 1: Back Wall: Select one 4.210m Base Plate (Green), one

4.210m Top Plate (Red) and six Studs (Yellow). Lay out Plates

and two Studs on a flat surface and nail together using two

75mm nails per join. Nail in remaining centre studs using Nogs

to get correct position. Position Nogs .883m below Top Plate

and nail in place. (All Plates, Studs and Nogs are joined to-

gether with two 75mm nails each end).

Step 2: Front Wall: Select one 4.210m Base Plate (Green), one

4.210m Top Plate (Red), four Studs (Yellow) and two

1.185m Nogs. Nail studs to each end of Plates. Nail in re-

maining two studs using 1.185m Nogs to get correct posi-

tion. Position Nogs .883m below Top Plate and nail in

place.

Step 3: End Wall: Select one 3.380m Base Plate (Green), one

3.380m Top Plate (Red), three Studs (Yellow) and

two .787m Nogs. Lay out Plates and one Stud on a flat sur-

face and nail Stud centrally between Plates. Nail remaining

Studs to Plates using .787m Nogs to get the correct posi-

tion. Position Nogs .883m below Top Plate and nail in

place. Repeat with second End Frame.

JACK STUDS

YELLOW

Note: For sheds with the Raised Floor Modification option the studs will be 1.780m long to allow the Wall Sheets to pro-

trude 20mm below the Bottom Plate. Refer to Raised Floor Modification section (Page 15).

MK4B TIMBER FRAME

Step 4: Stand up Back Wall frame and one End frame

and nail together, using two 75mm nails per join,

top and bottom. Stand remaining Frames up and

nail together. Nail in remaining .765m Nogs in

End Walls.

Step 5: Position middle Jack Stud, centrally on End Wall

Top Plates and nail in place. Nail remaining Jack

Studs in. Position middle Ridge Beam to Jack

Stud and skew-nail in place using two 75mm

nails each end. Pre-drilling holes before nailing

will prevent timber from splitting.

Step 6: Place intermediate Roof Beams by using Roofing

Nogs to determine correct position (see fig. 2).

Nail intermediate Roof Beams in place. Nail 70 x

45mm Roofing Nogs in place (End Wall) and 90

x 45mm Roofing Nogs in place (Middle).

Step 7: Place Frame in correct position, checking the shed is square and level.

Dynabolt Frame to concrete base as instructed on page 4.

Step 8: Temporarily brace each side and roof, making sure each side is square.

Nail strip bracing to outside of Frame (see page 4), making sure it is tight.

Nail multigrip brackets to each of the four bottom corners (two per cor-

ner). Use 30mm bracket nails supplied.

Note: Condensation can form on the underside of cladding. If building paper is required, fit now. The building paper

will need to be supported by netting or roofing twine.

fig.2.

MK4B WALL CLADDING

TO AVIOD CORROSION:

 Where at all possible try not to trap metal filings between two sheets. Remove all metal filings before riveting.

 Carbon in pencils reacts with the Zinc/Aluminium coating on steel. Use ink to mark steel.

TERMS EXPLANATION

 To Tack: To Tack on a wall sheet means to use minimum nails hammered partly in to hold Wall Sheets in position. Should

a Wall Sheet need to be re-positioned, the nails can easily be prized out.

 If a window is required, identify Wall Sheet(s) with window hole pre-cut. Lean up Wall Sheets where window(s) are to be located.

Note:

When fitting Ga-

ble End Sheets

ensure they over-

lap correctly (fig

1).

The overlap di-

rection may differ

from cladding

detail.

CLADDING DETAIL

Birds Eye View

fig. 1

MK4B WALL CLADDING

Step 1: Front Wall: Start at the left hand side. Posi-

tion the Wall Sheet with the LIP on the left hand

side. Ensuring the LIP is flush with side of the

Stud and the top of the Top Plate, tack in place.

Repeat with Wall Sheet on the right hand side

of doorway.

Step 2: Back Wall: Position the first Wall Sheet with

the LIP on the right hand side. Ensuring the LIP

is flush with the side of the Stud and the top of

the Wall Sheet is flush with the top of the Top

Plate, tack in place. Position the next Wall

Sheet with the LIP on the right hand side. Over-

lap as shown in fig.1 (page 7). Ensuring Wall

Sheet is flush with top of Top Plate, tack in

place. Repeat with remaining two sheets.

Step 4: Nailing Off: Nail one 30mm Clout each side of the Rib (two per Pan) into the Top Plates and Bottom

Plates. Nail Wall Sheets to mid wall Nogs (one per pan). Nail each corner Wall Sheet to Studs using two

30mm Clouts evenly spaced.

Gable Ends: When nailing Gable Wall Sheets to the Top Plate, use a String Line. At the top of the gable nail two

30mm Clouts into the end of the Ridge Beam. This will stop it from twisting.

Step 3: End Walls: Lean Gable Wall Sheets against

the shed to form gable shape. With the LIP

flush with side of Stud tack in place ensuring

the bottom of the Wall Sheet is 10mm above

the bottom of the Bottom Plate. Tack on re-

maining Wall Sheets. Repeat with other gable

end. If fitting a window, nail in Window Studs

and Nog now. Refer to Window instructions.

EDGE

FLUSH

TOP

FLUSH

MK4B LOUVRE WINDOW (Optional)

Step 2: On the inside of the shed, position studs

and Nog centrally on window opening.

Make sure the studs are parallel and nail

into Top Plate and end wall Nog.

Step 3: Nail wall Sheets to window framing using

30mm clouts. (return to step 4 on page 7

and complete). Then fit Window Frame).

Position Window Frame centrally on win-

dow opening and rivet it to ribs. Pre-drill

holes in each corner and nail Window

Frame to framing, using 50mm nails.

Step 4: If the Window is in the gable end, tempo-

rarily position the Over Panel above Win-

dow Frame. Following the same angle as

the gable, mark and cut to suit.

Step 5: Rivet Over Panel to the Window Frame

with rivets.

588mm

Step 1: Lay out the two window studs (883mm) and

Nog (634mm) on a flat surface. Position

Nog and nail in place using 2x 75mm nails

at each end.

Step 6: From the inside of the shed, slide Louvre

Glass into Louvre Units attached to the

Window Frame. Bend up tabs to keep

Glass in position.

50mm

NAILS

RIVITS

Step1: Fit Door Jamb Flashing (A104) in be-

tween Top and Bottom Plates and hard

against Stud. Attach Door Jamb Flash-

ing with three 30mm clouts into studs on

the inside and three rivets into Rib on

the outside. Pre-drill holes on the outside

to protect flashing. Repeat with the other

Door Jamb.

Step2: Measure and cut Doorstep Flashing (A106)

to fit in between Door Jambs. Positioning

the Doorstep Flashing in between Door

Jambs at bottom of doorway, nail through

top of flashing using five 30mm Clouts. Re-

peat with the Overdoor Flashing (A105).

Step 1: Lay out the two window studs (883mm) and

Nog (590mm) on a flat surface. Position

Nog and nail in place using two 75mm nails

at each end.

570mm

Step 6: From the outside of the shed, place glass

in Window Frame. Attach a Glazing Bead

(G100) with three rivets to each side of the

Window Frame to hold glass in place. Pre-

drilling Glazing Beads is recommended.

MK4B FIXED WINDOW (Optional)

Follow Steps 2 - 5 on page 8.

MK4B DOOR JAMB & CORNER FLASHINGS

Indice

Altri manuali Duratuf Deposito all'aperto

Duratuf

Duratuf PL44 Manuale utente

Duratuf

Duratuf GS72 Manuale utente

Duratuf

Duratuf TUF 100 Manuale utente

Duratuf

Duratuf GL95 Manuale utente

Duratuf

Duratuf Garrison PL36 Manuale utente

Duratuf

Duratuf PG66 Manuale utente

Duratuf

Duratuf GS63 Manuale utente

Duratuf

Duratuf GG109 Manuale utente

Duratuf

Duratuf MATAKANA Manuale utente

Duratuf

Duratuf MK4C Manuale utente

Duratuf

Duratuf TUF LOCKER Manuale utente

Duratuf

Duratuf SENTRY SHEDS SS1515 Manuale utente

Duratuf

Duratuf MK4A Manuale utente

Duratuf

Duratuf TUF 400 Manuale utente

Duratuf

Duratuf Sentry Sheds SL1515 Manuale utente

Duratuf

Duratuf SL3015 Manuale utente

Duratuf

Duratuf GL65 Manuale utente

Duratuf

Duratuf PS42 Manuale utente

Duratuf

Duratuf SG3020 Manuale utente

Duratuf

Duratuf TUF 400 Manuale utente

Duratuf

Duratuf SG2020 Manuale utente

Duratuf

Duratuf PG99 Manuale utente

Duratuf

Duratuf SG3025 Manuale utente

Duratuf

Duratuf Gurdian Sheds GG101 Manuale utente

Manuali Deposito all'aperto popolari di altre marche

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Manuale utente

TYGO

TYGO Nyland Manuale utente

Viking

Viking SD5300SS Manuale tecnico

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Manuale utente

ModuLaro

ModuLaro Lojo WC202200 Manuale utente

Lifetime

Lifetime 6418 Manuale utente

rollaway container

rollaway container ARPCA24 Manuale utente

X-METAL

X-METAL 4065 Manuale utente

Outdoor Life Products

Outdoor Life Products FP2030 F Manuale utente

Royalcraft

Royalcraft Faro 295L Storage Box Manuale utente

Riverlea

Riverlea Duratuf KIWI KS3 Manuale utente

OLT

OLT GS84D-FJ-Plywood Manuale utente

Rubbermaid

Rubbermaid 5L45 Manuale utente

garofalo

garofalo TUSCANY EVO Manuale utente

Eden

Eden CA2988 Manuale utente

Palram

Palram CANOPIA RUBICON 6x10 Guida per l'amministratore

Suncast

Suncast 774098 Manuale utente

Lifetime

Lifetime 60186 Manuale utente