Dwyer Instruments TS-13011 Istruzioni per l'installazione e il funzionamento

Series TS Digital Temperature Switch

Specifications - Installation and Operating Instructions

Bulletin E-90-TS

The TS Digital Temperature Switch is designed for many

heating and cooling applications. The probe temperature is

displayed on the bright 3-digit, red LED. The user is able to

program 12 different parameters including set point,

hysteresis, cycle time, and ambient probe adjustment using

the front keypad. The unit features error or alarm messaging

and password protection. Select between temperature

display in °F or °C, and 110 VAC, 230 VAC, or 12 VDC

power supplies. The TS includes a thermistor with 5 ft (1.5

m) cable, fitting clips for panel mounting, and instruction

manual.

INSTALLATION

NOTE:

Unit must be mounted away from vibration,

impacts, water and corrosive gases.

•

Cut hole in panel 2.80 x 1.14 inches (71 x 29 mm).

• Apply silicone (or rubber gasket) around the perimeter of

the hole to prevent leakage.

• Insert unit into hole in the panel.

• Slide removable fitting clips onto unit from the back until

secure to panel.

• Remove back cover to wire unit.

• Wiring diagram is displayed on the top of the unit.

•

(Note: PROBE CABLE LENGTH MUST NOT EXCEED

328 ft (100 m). DO NOT INSTALL PROBE CABLE NEAR

POWER CABLES).

• Replace cover once wiring is completed.

WIRING DIAGRAM

PARAMETERS

Description Units Range

SP Set Point Degrees r1 to r2

r0 Differential or Hysteresis Degrees 1 to 20

r1 Lower Value Set Point Degrees -50 to 150°

r2 Higher Value Set Point Degrees -50 to 302°F (-50 to 150°C)

d0 Heating or Cooling Control Option Ht/Co

d2 Time for Defrosting Minutes 0 to 59 min.

d8 Interval Time between Hours 1 to 24 hr.

Defrosting

c0 Min. Stop Time for Load Minutes 0 to 59 min.

c1 Continuous Cycle Time Hours 0 to 24 hr.

P1 Ambient Probe Adjustment Degrees -10 to 10

H5 Parameter Access Code Numeric 0 to 99 (SET AT 00 FROM FACTORY)

t0 Max. Temp. on Display Degrees -50 to 302°F (-50 to 150°C)

DWYER INSTRUMENTS, INC.

Phone: 219/879-8000 www.dwyer-inst.com

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A. Fax: 219/872-9057 e-mail: info@dwyer-inst.com

SPECIFICATIONS

Probe Range: -58 to 302°F (-50 to 150°C).

Input: 1.5-inch (4 cm) thermistor (1000Ω@ 25°C) with 5-foot

(1.5 m) cable.

Accuracy: ±1°.

Resolution: ±1 digit.

Output: 16 amp SPDT relay @ 250 VAC.

Horsepower Rating (HP): 1/3HP for 8 amp and 3/4HP for

16 amp.

Supply Voltage: 110 VAC, 230 VAC or 12 VDC/VAC, 24

VDC/VAC (depending on model).

Supply Power: 4 VA (230 V).

Ambient Temp: 14 to 158°F (-10 to 70°C).

Storage Temperature: -4 to 176°F (-20 to 80°C).

Front Panel Protection: IP64.

Display: 3-Digit, Red or Green (depending on model).

2.95

[75]

1.34

[34]

2.72

[69]

1.10

[28]

12789

10 11

SUPPLY

load

power

E-90-TS 8/6/07 3:45 PM Page 1

www. .com information@itm.com1.800.561.8187

DWYER INSTRUMENTS, INC.

Phone: 219/879-8000 www.dwyer-inst.com

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A. Fax: 219/872-9057 e-mail: info@dwyer-inst.com

PARAMETER DESCRIPTIONS

SP = Set Point - Desired Regulation Temperature.

r0 = Differential or Hysteresis.

r1 = Lower Set Point Limit.

r2 = Higher Set Point Limit.

d0 = Heating or Cooling Control - This control only does

regulation cycles. Neither defrosting nor continuous

cycles exist.

Heating: To choose Heating Control - Set d0=Ht

(The output is activated when TS1 [temperature of

ambient probe] is less than or equal to Set Point.)

TS1<=SP. It then disconnects when TS1>=SP-r0.

Cooling: To choose Cooling Control - Set d0=Co

(The output is activated when TS1>=SP+r0.) The

display will switch off when TS1<=Set.

d2 = Duration of Defrosting Time (The value

programmed from the factory is d2=15 minutes.

[Ht-defrosting will never start, if Co=0, defrosting

will never start.])

d8 = Interval time between defrosting.

c0 = Minimum time between start and stop.

c1 = Continuous cycle time.

P1 = Ambient Probe Calibration. (Offset degrees to

adjust ambient probe. If the probe is not placed in

the exact point that is to be measured, use a

standard thermometer and adjust the difference in

this parameter.)

H5 = Access to probe parameters. (This code is set to

00 from the factory.)

t0 = Maximum temperature on display. (Temperature

limit for defrosting.)

PARAMETER PROGRAMMING

Access set point (SP) without code protection.

• Press SET. SP text will appear on the display.

• Press SET again. The real value is shown on the

display.

• The value can be modified with the UP and DOWN

arrows.

• Press SET to enter any new values.

• Press SET and DOWN at the same time to quit

programming or wait one minute and the display

will automatically exit programming mode.

The keyboard code can be reset to ZERO by

turning off the controller and turning it on again

while keeping the SET key depressed.

Access to all code protected parameters.

• Press SET for 8 seconds. The access code value

00 is shown on the display. (Unit comes with

code set at 00 from factory).

• With the UP and DOWN arrows, code can be set to

user needs.

• Press SET to enter the code. If it is correct, the first

parameter label is shown on the display (SP).

• Move to the desired parameter with the UP and

DOWN keys.

• Press SET to view the value on the display.

• The value can be modified with the UP and DOWN

arrows.

• Press SET to enter the value and exit to test

parameter.

• Press SET and DOWN at the same time to quit

programming or wait one minute and the display will

automatically exit programming mode.

LED INDICATIONS

OUT This indicates the load is connected. The

system waits for the programmed minimum

stop time of the load.

Def This indicates defrosting is activated.

DISPLAY MESSAGES

In normal operation, the probe temperature will be shown

on the display. In case of alarm or error, the following

messages will be shown:

•ER = Memory Error

•-- = Short-Circuit Probe Error

•oo = Open Probe Error

MAINTENANCE/REPAIR

After final installation of the TS Series Digital Temperature

Switch, no routine maintenance is required. A periodic

check of system calibration is recommended. These

devices are not field repairable and should be returned to

the factory if recalibration or other service is required. After

first obtaining a Returned Goods Authorization (RGA)

number, send the material, freight prepaid, to the following

address. Please include a clear description of the problem

plus any application information available.

Dwyer Instruments Inc.

Attn: Repair Department

102 Highway 212

Michigan City, IN 46360

E-90-TS 8/6/07 3:45 PM Page 2

www. .com information@itm.com1.800.561.8187

Questo manuale è adatto per i seguenti modelli

Altri manuali Dwyer Instruments Interruttore

Dwyer Instruments

Dwyer Instruments PHOTOHELIC 3000 SERIES SGT Istruzioni per l'installazione e il funzionamento

Dwyer Instruments

Dwyer Instruments TSXT Series Istruzioni per l'installazione e il funzionamento

Dwyer Instruments

Dwyer Instruments A3000 series Manuale utente

Dwyer Instruments

Dwyer Instruments L8-WP FLOTECT Manuale utente

Dwyer Instruments

Dwyer Instruments PROXIMITY TFLS Series Istruzioni per l'installazione e il funzionamento

Dwyer Instruments

Dwyer Instruments W.E. Anderson Flotect L6 Istruzioni per l'installazione e il funzionamento

Dwyer Instruments

Dwyer Instruments DPL Manuale utente

Dwyer Instruments

Dwyer Instruments TDS Series Manuale utente

Dwyer Instruments

Dwyer Instruments MP Mini-Photohelic Manuale utente

Dwyer Instruments

Dwyer Instruments ADPS-08-2-N Istruzioni per l'installazione e il funzionamento

Dwyer Instruments

Dwyer Instruments PROXIMITY VRLS-01 Manuale utente

Dwyer Instruments

Dwyer Instruments Series A3000 Photohelic Manuale utente

Dwyer Instruments

Dwyer Instruments 530 Manuale utente

Dwyer Instruments

Dwyer Instruments W.E. Anderson Flotect V4 Series Istruzioni per l'installazione e il funzionamento

Dwyer Instruments

Dwyer Instruments Love 40T Series Istruzioni per l'installazione e il funzionamento

Dwyer Instruments

Dwyer Instruments 1910-00 Manuale utente

Dwyer Instruments

Dwyer Instruments CFS2 Series Manuale utente

Dwyer Instruments

Dwyer Instruments SCS Series Manuale utente

Dwyer Instruments

Dwyer Instruments TS2 Series Istruzioni per l'installazione e il funzionamento

Dwyer Instruments

Dwyer Instruments MP Mini-Photohelic Series Istruzioni per l'installazione e il funzionamento

Dwyer Instruments

Dwyer Instruments Mini-Photohelic MP Series Manuale utente

Dwyer Instruments

Dwyer Instruments CMS300 Istruzioni per l'installazione e il funzionamento

Dwyer Instruments

Dwyer Instruments Proximity PLS2 Istruzioni per l'installazione e il funzionamento

Dwyer Instruments

Dwyer Instruments F7 Series Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente