Dynamic Engineering PCI2PMC Manuale utente

DYNAMIC ENGINEERING

150 DuBois St. Suite C, Santa Cruz, Calif. 95060

831-457-8891 Fax 831-457-4793

http://www.dyneng.com

[email protected]

Est. 1988

User Manual

PCI2PMC

PCI Single Slot PMC Compatible Carrier

Use Your PMC in a PC

Manual Revision H1

Corresponding Hardware: Revision H

10-2000-0608

Embedded Solutions Page 2

PCI2PMC

PCI and PMC Compatible Carrier

Dynamic Engineering

150 DuBois St. Suite C

Santa Cruz, CA 95060

831-457-8891

831-457-4793 FAX

This document contains information of

proprietary interest to Dynamic Engineering. It

has been supplied in confidence and the

recipient, by accepting this material, agrees that

the subject matter will not be copied or

reproduced, in whole or in part, nor its contents

revealed in any manner or to any person except

to meet the purpose for which it was delivered.

Dynamic Engineering has made every effort to

ensure that this manual is accurate and

complete. Still, the company reserves the right to

make improvements or changes in the product

described in this document at any time and

without notice. Furthermore, Dynamic

Engineering assumes no liability arising out of

the application or use of the device described

herein.

The electronic equipment described herein

generates, uses, and can radiate radio

frequency energy. Operation of this equipment

in a residential area is likely to cause radio

interference, in which case the user, at his own

expense, will be required to take whatever

measures may be required to correct the

interference.

Dynamic Engineering’s products are not

authorized for use as critical components in life

support devices or systems without the express

written approval of the president of Dynamic

Engineering.

Connection of incompatible hardware is likely to

cause serious damage.

Other trademarks and registered trademarks are

owned by

their respective manufactures.

Manual Revision H1. Revised January 20, 2010

Embedded Solutions Page 3

Table of Contents

PRODUCT DESCRIPTION 5

USAGE NOTES: 6

Notes: 8

PMC MODULE BACKPLANE IO INTERFACE PIN ASSIGNMENT 9

APPLICATIONS GUIDE 10

Interfacing 10

Construction and Reliability 11

Thermal Considerations 11

WARRANTY AND REPAIR 12

Service Policy 12

Out of Warranty Repairs 12

For Service Contact: Customer Service Department Dynamic Engineering 12

SPECIFICATIONS 13

ORDER INFORMATION 14

Embedded Solutions Page 4

List of Figures

FIGURE 1 PCI2PMC PN4 INTERFACE STANDARD 9

Embedded Solutions Page 5

Product Description

PCI2PMC is part of the PCI and PMC Compatible family of modular I/O components.

The PC2PMC adapts one PMC to one PCI slot. Dynamic Engineering has several

versions of the PCI2PMC including bridged and two slot versions. The PCI2PMC is a

single slot passive design.

Special features:

• Universal PCI 1/2 length card.

LED’s are green and steady on when the voltages are active.

• LED1 is PMC Busmode “Present”

• LED2 is 3.3V to PMC

• LED3 is 3.3 from PCI bus.

• LED4 is 3.3 from Regulator

• LED5 is plus 5

• LED6 is plus 12

• LED7 is minus 12

• Jumper selection for onboard 1500mA regulator or PCI 3.3V supply

• 32 or 64 bit operation

•10 ohm series resistors on AD31-0

• Clamping Diodes on critical PCI signals

• Zero delay buffer for PCI clock distribution

• PrPMC clocking options

• Front panel connector access through PCI bracket

• User IO [Pn4] available through 2 cable connectors (DIN IDC and SCSI II compatible)

• Spare pins on SCSI connector can be jumper selected to 5V or ground.

• Matched length IO.

• Cooling cutout for increased airflow to PMC

• Jumper selection on M66EN

• JTAG and Monarch mode control header options

PCI2PMC is a passive design incurring no added delays in connection from the PCI to

the PMC buses. The design incorporates features to prevent the physical length of the

traces from affecting operation. There may be cases where the backplane can’t support

all slots with PCI2PMC cards installed.

Our bridged products including PCIBPMC, PCIBPMCET, PCIBPMCX1, and

PCIBPMCX2 can be used in situations where a bridge is desired. Please refer to the

Dynamic Engineering website for more information on these and other products.

Embedded Solutions Page 6

Usage Notes:

The regulator LED may not illuminate unless there is a load from the PMC on the 3.3V

supply, and the regulator is selected as the power source for the 3.3V.

The Regulator path can provide up to 1500 mA of 3.3V power. Two FET’s are used to

allow the user to select PCI 3.3V or local regulator as the source for the 3.3V power to

the PMC. If the PMC uses more than 1.5A the PCI selection must be made.

The FET has a small internal resistance and the protection DIODE has a separate

current sensitive drop. For low current levels the IR drop is small and the 3.3 will be

with the legal range. For larger current levels the –HC option should be selected to

minimize the voltage drop.

Jumper options are clearly marked in the component side silk screen.

J1 3.3V Source selector. open = regulated, installed = PCI source.

J2 Connected to pins 33, 67 on P2. 1-2 = 5V, 2-3 = GND installed with –SCSI

J3 Connected to pins 34, 68 on P2. 1-2 = 5V, 2-3 = GND installed with -SCSI

J4 Connected to M66EN. Installed = GND = 33 MHz. Open = bus condition = 33 or 66

MHz.

J5 is the JTAG Header with options for connection to PCI bus or from Flying leads.

Installed with -JTAG

PCI Side PMC Side

TRST# 1 2

TCK 3 4

TMS 5 6

TDI 7 8

TDO 9 10

The header can be jumpered across to connect the PCI side to the PMC side or the

PMC side can be connected to flying leads from your JTAG interface.

J8 Pin 1 = 3.3, and pin 2 = gnd used for reference with JTAG

Add –JTAG to the Part Number if you need J5 and J8 installed.

Embedded Solutions Page 7

J6 and J7 control the PrPMC clock options. Installed with –M option.

J6 J7

OPN OPN PCI CLK VIA PLL TO PMC – standard non –M signal path.

SHNT SHNT OSC TO BP & PMC BIPASS PLL

SHNT OPN OSC TO BP & PMC USING PLL

OPN SHNT PMC DRIVING CLOCK TO BP

J9 is installed when the –M option is requested. J9 is a two pin header. When a shunt

is installed the 1KΩresistor provides a pull-down. When open a 10KΩresistor provides

the pull-up. The installed PrPMC can usually override either setting after power-up

using software.

PCI2PMC is a product consisting of a PCB and added components. The components

can be swapped or left off to create different versions.

The standard version of the board is called “PCI2PMC” and comes with a complete 64

bit PCI path to support 32 and / or 64 bit operation at 33 and / or 66 MHz. The PMC

may have IO through its bezel or via Pn4 or both. The Bezel IO is supported via the

PCI rear IO port. The Pn4 IO is supported with either a DIN or SCSI connector. The

DIN connector is standard and the –SCSI option swaps the DIN for the SCSI.

The PCI2PMC–ME version removes the Upper part of the PCI bus and the rear IO

leaving the primary 32 bit PCI path and PMC Bezel IO. This version is usually provided

with the –HC option to remove the regulator and FET’s etc. to provide a hardwired PCI

3.3V sourced board.

The PCI2PMC, PCI2PMC-SCSI, and PCI2PMC-ME-HC are stocked items. Other

combinations are built to order. Please see the last page for more ordering options.

Embedded Solutions Page 8

Notes:

A) Revision 4 and later boards M66EN is connected to the PMC slot [Jn2-47].

Recent revision 3 boards are reworked to have the equivalent functionality.

B) Shunts are capable of 800 mA. The Shunts on J2,J3 are not fuse protected.

Your circuit must limit total power consumed.

C) Rev 1-4 required –HC option for more than 800 mA of 3.3V from the backplane to

be routed to the PMC. Revision 5 and later have MOSFET switches controlled

by J1 with a 10A rating. The local regulator has been upgraded to 1500 mA.

D) Revision 5 and later boards with the PrPMC option; not installed unless ordered.

Standard configuration is the equivalent of the PCI clock through the PLL to the

PMC.

E) Rev 5 and later boards have power reference for JTAG header.

F) Rev 7 switched to 0603 capacitors and increased quantity

G) Rev 8 has matched length IO for Pn4.

Embedded Solutions Page 9

PMC Module Backplane IO Interface Pin Assignment

The figure below gives the pin assignments for the PMC Module IO Interface – from

Pn4 to the PCI2PMC connectors. Also see the User Manual for your PMC board for

more information.

DIN IDC [P3] SCSI II [P2] Pn4

C1 A1 1 35 1 2

C2 A2 2 36 3 4

C3 A3 3 37 5 6

C4 A4 4 38 7 8

C5 A5 5 39 9 10

C6 A6 6 40 11 12

C7 A7 7 41 13 14

C8 A8 8 42 15 16

C9 A9 9 43 17 18

C10 A10 10 44 19 20

C11 A11 11 45 21 22

C12 A12 12 46 23 24

C13 A13 13 47 25 26

C14 A14 14 48 27 28

C15 A15 15 49 29 30

C16 A16 16 50 31 32

C17 A17 17 51 33 34

C18 A18 18 52 35 36

C19 A19 19 53 37 38

C20 A20 20 54 39 40

C21 A21 21 55 41 42

C22 A22 22 56 43 44

C23 A23 23 57 45 46

C24 A24 24 58 47 48

C25 A25 25 59 49 50

C26 A26 26 60 51 52

C27 A27 27 61 53 54

C28 A28 28 62 55 56

C29 A29 29 63 57 58

C30 A30 30 64 59 60

C31 A31 31 65 61 62

C32 A32 32 66 63 64

33 67 Open, +5 or GND via J2 silk screen defined

34 68 Open, +5 or GND via J3

FIGURE 1 PCI2PMC PN4 INTERFACE STANDARD

Read table:

P3-C1 = P2-1 = Pn4-1

P3-A1 = P2-35 = Pn4-2

etc.

Embedded Solutions Page 1 0

Applications Guide

Interfacing

Some general interfacing guidelines are presented below. Do not hesitate to contact the

factory if you need more assistance.

Installation

The PMC is mounted to the PCI2PMC prior to installation within the chassis. For best

results: with the PCI bracket installed, install the PMC at an angle so that the PMC front

panel bezel penetrates the PCI bracket then rotate down to mate with the PMC [JnX -

PnX] connectors.

If the PCI bracket is not installed, plug in the PMC and then attach the PCI bracket. Use

the mounting screws that come with the PMC to secure to the PCI2PMC.

There are four mounting locations. Two into the PMC mounting bezel and two for the

standoffs near the PMC bus connectors.

Start-up

Make sure that the "system" can see your hardware before trying to access it. Many

BIOS will display the PCI devices found at boot up on a "splash screen" with the

VendorID and CardId for the PMC installed and an interrupt level.

Watch the system grounds. All electrically connected equipment should have a fail-

safe common ground that is large enough to handle all current loads without affecting

noise immunity. Power supplies and power consuming loads should all have their own

ground wires back to a common point.

Power all system power supplies from one switch. Connecting external voltage to

the PCI2PMC when it is not powered can damage it, as well as the rest of the host

system. This problem may be avoided by turning all power supplies on and off at the

same time. This applies more to the PMC installed into the PCI2PMC than the

PCI2PMC itself, and it is smart system design when it can be achieved.

Indice

Altri manuali Dynamic Engineering Scheda PCI

Dynamic Engineering

Dynamic Engineering cPCIBPMC6U Manuale utente

Dynamic Engineering

Dynamic Engineering PC104p-SpaceWire-Monitor Manuale utente

Dynamic Engineering

Dynamic Engineering PCIe8LSwVPX3U Manuale utente

Dynamic Engineering

Dynamic Engineering LVDS 8R Manuale utente

Dynamic Engineering

Dynamic Engineering PCIe8LXMCX2CB Manuale utente

Dynamic Engineering

Dynamic Engineering PCIeBiSerialDb37-LM9 Manuale utente

Dynamic Engineering

Dynamic Engineering SpaceWire BK Manuale utente

Dynamic Engineering

Dynamic Engineering PCIe 8L XMC X1 Manuale utente

Manuali Scheda PCI popolari di altre marche

ERMA

ERMA SSI 1417 Manuale utente

SIIG

SIIG CyberSerial Dual PCI Istruzioni per il montaggio

Moxa Technologies

Moxa Technologies CP-102E Manuale utente

I-Bus

I-Bus IBC2602 Manuale utente

Exsys

Exsys EX-60102 Manuale utente

Chelsio Communications

Chelsio Communications T5 Series Manuale utente

Conrad Electronic

Conrad Electronic 97 46 71 Manuale utente

Micro Innovations

Micro Innovations USB650A Manuale utente

KTI Networks

KTI Networks KF-310 Manuale utente

Asus

Asus SpaceLink WL230 Manuale utente

SIIG

SIIG SC2475 Manuale utente

TRENDnet

TRENDnet TEW-703PI Manuale utente

Belkin

Belkin F5D7000F Manuale utente

Pericom

Pericom PI7C7100 Manuale utente

ADLINK Technology

ADLINK Technology cPCI-3548 Manuale utente

Digium

Digium TE200 Series Manuale utente

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manuale utente

Western Digital

Western Digital FireWire PCI Adapter Manuale utente