Dynamic Projection JCD Manuale utente
1
Copyright © 2014 - 2017 Dynamic Projection Institute GmbH. All rights reserved. http://www.dynamicprojection.com
Weights and dimensions shown are approximate. Specications and appearance are subject to change without notice. Version 1.8Version 1.8
JCD Manual
VERSION: 1.8
JCD
1
Copyright © 2014 - 2017 Dynamic Projection Institute GmbH. All rights reserved. http://www.dynamicprojection.com
Weights and dimensions shown are approximate. Specications and appearance are subject to change without notice.
2
Copyright © 2014 - 2017 Dynamic Projection Institute GmbH. All rights reserved. http://www.dynamicprojection.com
Weights and dimensions shown are approximate. Specications and appearance are subject to change without notice. Version 1.8
Table of Content
Introduction 3
Warranty 3
Warnings and Safety 4
JCD Control Unit 5
Physical Setup 6
Network Access 7
Web Interface 8
JCD Status 9
JCD Configuration - Projector 10
JCD Configuration - Expert Configuration 11
Lense Calibration 12
Focus & Zoom Control 13
Lense Memory 14
Basic System Control 15
Art-Net/ DMX512 Control 16
Sysinfo & Log 17
Updating JCD 18
DMX Fixture/ Head/ Personality 19 – 21
3
Copyright © 2014 - 2017 Dynamic Projection Institute GmbH. All rights reserved. http://www.dynamicprojection.com
Weights and dimensions shown are approximate. Specications and appearance are subject to change without notice. Version 1.8
Introduction
Thank you for having chosen a JCD unit. If you follow the instructions given in this manual, we are sure you will enjoy this device
for a long period of time.
For your own safety, please read this user manual carefully before you initially start-up.
Every person involved with the installation, operation and maintenance of this device has to:
- be qualified
- follow the instructions of this manual
- consider this manual to be part of the total product
- keep this manual for the entire service life of the product
- pass this manual on to every further owner or user of the product
- download the latest version of the user manual from our website
In the case you have questions about our product or need support during assembly and installation please contact our support!
Dynamic Projection Institute, Herstellungs und Vertriebs GmbH
Renngasse 4/1/1, A-1010 Vienna
Email: offi[email protected]
Web: www.dynamicprojection.com
Phone: +43 1 996 2028 (Mo. - Fr. from 9:00 to 18:00h)
Commercial Register: FN400806x
Warranty
DPI represents and warrants:
- that all Products will be in a fully working and commercially available condition.
- for twelf (12) months from the date of proof of purchase by a customer, unless otherwise agreed.
Warranty is void if the operator of the device violates any safety and / or operation advice in this manual.
4
Copyright © 2014 - 2017 Dynamic Projection Institute GmbH. All rights reserved. http://www.dynamicprojection.com
Weights and dimensions shown are approximate. Specications and appearance are subject to change without notice. Version 1.8
Warnings and Safety
*This product shall only be connected to an external power supply
rated at 5V dc, and a minimum current of 2A . Any external power
supply used with the JCD shall comply with relevant regulations
and standards applicable in the country of intended use.
* This product should not be overclocked as this may make
certain components very hot.
*This product should be operated in a well ventilated environment
and should not be covered.
* This product should be placed on a stable, flat, non-conductive
surface in use and should not be contacted by conductive items.
* The connection of unapproved devices to the GPIO, USB,
HDMI, Network or Audio connector may affect compliance or
result in damage to the unit and invalidate the warranty.
Instructions for safe use
To avoid malfunction or damage to your JCD please observe the
following:
* Do not expose it to water, moisture or place on a conductive
surface whilst in operation.
* Do not expose it to heat from any source; the JCD is designed
for reliable operation at normal ambient room temperatures.
* Take care whilst handling to avoid mechanical or electrical
damage to the printed circuit board and connectors.
* Avoid handling the JCD while it is powered. Only handle by the
edges to minimise the risk of electrostatic discharge damage.
* All peripherals used with the JCD should comply with relevant
standards for the country of use and be marked accordingly to
ensure that safety and performance requirements are met.
*The JCD is not designed to be powered from a USB port on other
connected equipment, if this is attempted it may malfunction.
Compliance information
The JCD (Raspberry Pi) complies with the relevant provisions of
the RoHS Directive for the European Union.
WEEE directive statement for the european union
In common with all Electronic and Electrical products the JCD
(Raspberry Pi) should not be disposed of in household waste.
Alternative arrangements may apply in other jurisdictions.
Emc compliance statements european union
(eu) electromagnetic compatibility directive
compliance statement
* This product is in conformity with the protection requirements
of EU Council Directive 2004 / 108 / EC on the approximation
of the laws of the Member States relating to electromagnetic
compatibility.
* This product has been tested and found to comply with the
limits for Class A Information Technology Equipment according
to the European Standard EN 55022.
WARNING:This is an EN 55022 Class A product. In a domestic
environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Federal communications commission (FCC)
emissions compliance statement
* This equipment has been tested and complies with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment.
* This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device might
not cause harmful interference, and (2) this device must accept
any interference received, including interference that might
cause undesired operation.
WARNING: Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will
be required to correct the interference at their own expense.
Industry canada class a emissions compliance
statement
*This Class A digital apparatus complies with Canadian ICES-003.
Australia and new zealand class a emissions
compliance statement
WARNING:ThisisaClassAproduct.Inadomesticenvironment
this product may cause radio interference in which case the
user may be required to take adequate measures.
5
Copyright © 2014 - 2017 Dynamic Projection Institute GmbH. All rights reserved. http://www.dynamicprojection.com
Weights and dimensions shown are approximate. Specications and appearance are subject to change without notice. Version 1.8
1
2
3
4
JCD Control Unit
1.2GHz Quad-Core 64bit control unit with max. power 12W.
(1) JCD Control Unit with internal WiFi accesspoint 802.11 b / g / n
(2) Micro USB power socket
(3) Network connector
(4) USB 2.0 connectors
USB to RS232 adapter
USB 2.0 powered adapter for serial speeds up to 128000 Baud
(5) USB connector
(6) RS232 connector male
AC adapter
Input 100 – 240V / Output 2,5A / 5V
(8) Socket connector
(9) Micro USB connector
5
6
9
8
7
6
Copyright © 2014 - 2017 Dynamic Projection Institute GmbH. All rights reserved. http://www.dynamicprojection.com
Weights and dimensions shown are approximate. Specications and appearance are subject to change without notice. Version 1.8
Physical Setup
1. Set up the projector (power, input,…) according to the projector manufacturer’s specification. Make sure that the projector has
RS232 communication enabled, and write down the serial settings of the projector – these will be needed later for
configuration. Please consult the projector manual for the default settings if these settings can not be found in the projector’s
on-screen menus.
2. Connect the USB to RS232 adapter: plug in the RS232 connector (6) to the projector’s serial (in) port and the USB connector
(5) to any of the USB ports (4) of the control unit.
3. Connect the AC adapter: plug in the Micro USB connector (7) into the control unit’s Micro USB power socket (2) and connect
the power socket connector (8) to a power socket. Flip the power switch to turn the control unit on, this will take a few seconds.
4. (optional) For Ethernet connectivity, plug in a CAT5/6 cable into the RJ45 jack (3) of the control unit and connect it to your
network infrastructure.
To ensure correct operation of JCD, please make sure that you follow the guidelines listed below:
- DO NOT use an AC adapter other than the one supplied
- DO NOT use a USB to RS232 converter other than the one supplied
- DO NOT unplug the AC adapter before the system has been safely shut down via the web interface
- DO NOT unplug the USB to RS232 converter during operation
- DO NOT open the control unit or any of the other supplied parts, there are no serviceable parts inside
- DO NOT alter or modify any of the supplied parts
- DO NOT connect any device other to the control unit other than the supplied parts and projectors (and USB pen drives in case
you need to update)
- DO NOT update a working system unless necessary
- DO NOT use old or outdated browsers to access the web interface – JCD has been tested with Google Chrome and Mozilla
Firefox – other browsers will probably work but your mileage may vary)
Micro
USB
Power
Supply
USB
Wifi
RS232
Art-Net™
7
Copyright © 2014 - 2017 Dynamic Projection Institute GmbH. All rights reserved. http://www.dynamicprojection.com
Weights and dimensions shown are approximate. Specications and appearance are subject to change without notice. Version 1.8
Network Access
Communication with the control unit is possible via both Ethernet and Wi-Fi. The device acts as a Wi-Fi hotspot, you should be able to
find a network named “JCD-xxxxxxxx” with “xxxxxxxx” being a combination of numbers and letters. The exact SSID as well as the
WPA key can be found on a sticker on the control unit itself. The default IP address of the Wi-Fi hotspot is 192.168.1.1.
The default IP address of the Ethernet device is 2.0.0.20 (netmask 255.0.0.0), which can be changed via the web interface (see below).
If you want to use the default IP address, you have to change the network settings of your communicating devices accordingly.
8
Copyright © 2014 - 2017 Dynamic Projection Institute GmbH. All rights reserved. http://www.dynamicprojection.com
Weights and dimensions shown are approximate. Specications and appearance are subject to change without notice. Version 1.8
Web Interface
Once you have established network access, enter the default IP address (192.168.1.1 for Wi-Fi; 2.0.0.20 for Ethernet) in a browser of
your choice. The JCD splash screen should appear, click on the logo to enter the web interface.
The web interface is divided into several tabs:
- “Welcome & Help” – JCD manual
- “Basic System Control” – access to basic commands
- “Focus & Zoom Control” – main lens control interface
- “System Setup & Calibration” – system configuration and lens calibration
- “Sysinfo & Log” – internal system information and ArtNet/DMX log
9
Copyright © 2014 - 2017 Dynamic Projection Institute GmbH. All rights reserved. http://www.dynamicprojection.com
Weights and dimensions shown are approximate. Specications and appearance are subject to change without notice. Version 1.8
JCD Status
In the upper right corner, the web interface provides the system status, which will be refreshed every second. On successful setup,
the system should be in the “IDLE” state, meaning that JCD is ready and waiting to accept commands.
If the status is “ERROR” instead, the USB to RS232 converter is not connected to the control unit. Plug in the USB to RS232 converter
and the status should change to “IDLE”. If you unplug the USB to RS232 converter again, the status will switch back to “ERROR” instead.
If you encounter the “FAIL” status, please contact Dynamic Projection Institute and attach the information from the “Sysinfo” section
on the “Sysinfo & Log” tab!
10
Copyright © 2014 - 2017 Dynamic Projection Institute GmbH. All rights reserved. http://www.dynamicprojection.com
Weights and dimensions shown are approximate. Specications and appearance are subject to change without notice. Version 1.8
JCD Configuration - Projector
In order to be able to interact with the projector, JCD needs to be configured with the serial connection settings. Switch to the
“System Setup & Calibration” tab and open the “JCD Config” section.
The system is able to detect these settings automatically, click on the “Press to start autodetection...” button to start the detection.
The autodetection will take some time, information about the progress will be displayed below the button. When the process is
complete, the message “Probing finished.” will appear, and the detected settings for projector class, serial device, serial baudrate and
serial parity will be displayed below the message “Found projector!”. Copy these into the input fields on the left side and click on the
“Save Config...” button to save the configuration. A confirmation is required to prevent accidental overwriting of the current settings.
NOTE: In some cases, you may have to modify the “Serial delay” option to reflect the time for one lens step / before the
projector can accept the next command. Please consult the manual of the projector for further information.
Indice
Altri manuali Dynamic Projection Accessori per proiettori
Dynamic Projection
Dynamic Projection Mirror Head MH21 Manuale utente
Dynamic Projection
Dynamic Projection MH28 Manuale utente
Dynamic Projection
Dynamic Projection Mirror Head MH14 Manuale utente
Dynamic Projection
Dynamic Projection MH25 Manuale utente
Dynamic Projection
Dynamic Projection MH08 Manuale utente
Dynamic Projection
Dynamic Projection MH23 Manuale utente
Dynamic Projection
Dynamic Projection MH33 Manuale utente
Dynamic Projection
Dynamic Projection NEC NP-P506QL Manuale utente
Dynamic Projection
Dynamic Projection MH16 Manuale utente
Dynamic Projection
Dynamic Projection Mirror Head MH14 Manuale utente
