Eaglemaster E8 Manuale utente
IMPORTANT:
Please read the entire manual for complete details on the features, accessories and
operation before attempting to use your security system.
This Security system must be installed by a qualified technician to ensure proper
operation. Do not attempt to install or modify this system yourself as
this way void your warranty.
2-WAY CAR ALARM SYSTEM
WITH REMOTE ENGINE START
MODEL
About Your System
NOTE:
Congratulations on yourpurchase of this state-of-the-art vehicle securitysystem.
With proper installationthis system will provide superior protectionand performance for
many years tocome.
What is included:
Acontrol module
Tranceiver module
One 5-button 2-wayLCD remote transmitter
One 4-button randomcode remote transmitter
Dual stage shocksensor
High output 6-tonesiren (optional)
Full set wireharness
Pin switches
Options and Accessories:
This system includesseveral optional inputs and outputs allowingthe creation ofa
completely personalized securityand convenience systemby offering manyoptional
features such as:
2nd stage doorunlock
Channel programme timeoutput
2pulse signal doorunlock
Engine turbo timemode
Check range notification
Arm/disarm chirpon/off
*Many require additionalparts and/or labor, see storefor details
Some of thefeatures described in this manual may required additional partsand/or
labor, andmay not be included as part of the standardinstallation of thisunit.
Additionally, manyfeatures of this security system haveselectable options thatmust be
activated or programmedduring the system'sinstallation. These itemswill be identified
in the followingsections. Please discuss these features and any questions youmay
regarding the installationof this product with your authorized dealer.
Window close control
Anti car-jack byignition turn
Power trunk/hatch release
Glass breakage sensor
Micro-wave detector
Back-up battery siren
Functions of remotetransmitters
The remote transmittersintegrated with the security system usethe most perfectand
reliable radio frequency transfer as opposed to all car security systems being sold at the
moment. Some of modern skilled car hijackers use the devices known as code grabbers
allowing to accept and keep a signal transferred by the remote control of the car security
system. As soon as the driver is out the code is used by the hijacker to disarm the system.
Unlike the remote controls described above the remote transmitters integrated with your
security system change the code of the transferred signal each time when the button is
pressed, therefore, when a hijacker reproduces the signal grabbed from your remote
transmitter, thesecurity system just will not react.
Functions of remotetransmitterbuttons
Button to armthe system (ARM)
Button to disarmthe system (DISARM)
Button to controlremote engine start
Button to controlTrunk open / CH-1 active
Button to checkcar status , to turn onLCD back light
Fig.1
2-way remote #TR-45 1-way remote #TX-4R
Standard LCD 2-wayicon instructions
Remote transmitting asignal.
System Armed.
Passive arming &
Auto re-arming mode.
Panic mode.
Check-in range turnON status.
System Disarmed.
Zone1
1st-stage sensor bypass.
Zone2
1st-stage sensor bypass.
Silent Armed.
Zone1
2nd-stage sensor bypass.
Zone2
2nd-stage sensor bypass.
2way battery levelindication.
Door open whenarmed. Trunk open whenarmed. Hood open whenarmed.
Zone1
1st stage sensortriggered.
Zone1
2nd stage sensortriggered.
Zone2
1st stage sensortriggered.
Zone2
1st stage sensortriggered. Door switch triggered. Trunk switch triggered.
Ignition switch triggered.
Hood switch triggered. Immobilizer mode.
Valet mode. Safety mode/ Safestatus
Remote engine runningmode. Clock time enginestart mode. Fix time enginestart mode.
Temperatureengine start mode.
Anti car-jacking mode.
Turbo mode. Call / pagemode.
Battery conservemode. Remote button lock Vibrate mode.
Remote Function Table:
Functions Step Condition
Arm and door lock
Arm without siren chirp
Zone1- 1st-stage bypass
Zone1- 2nd-stage bypass
Car search mode
Standby Anti-Hi-Jack mode
Disarm and door unlock
Disarm without siren chirp
Arm with engine run mode
Remote engine start
Remote engine stop
Safety mode (manual-type car)
Zone2- 1st-stage bypass
Zone2- 2nd-stage bypass
Press once
Press over 2sec. until 1 beep given.
Press once within 5sec. of arming.
Press twice within 5sec. of arming.
Press once after 5sec. of arming.
Press over 2sec. Until 1 beep given.
Press once
Press over 2sec. until 1 beep given.
Press over 2sec. Until 1 beep given.
Press over 2sec. then press once.
Press over 2sec.
Press over 2sec.
Press once within 5sec. of arming.
Press twice within 5sec. of arming
Disarmed & ACC off
Disarmed & ACC off
Arming after 5sec.
ACC ON
Engine running
Armed with safe status
Arming within 5sec.
Arming within 5sec.
Armed
Armed
Engine running mode
Engine running
Arming within 5sec.
Arming within 5sec.
Remote Function Table:
Functions Step Condition
Trunk open / CH-1 active
Prolong engine running time
Enable check-in range
Status check & Back light
Indoor temperature check
Silent armed
Valet mode
Panic mode
Anti-Hi-Jack mode
FIX time engine start
Temperature engine start
CH-2 active
CH-3 active
CH-4 active
Press over 2sec. until 1 beep given
Press once, after LCD indicate 3min left.
Press once within 5sec. of arming.
Press once
Press over 2sec. Until 1 beep given.
Press over 2sec. Until 1 beep given.
Press over 2sec. until 1 beep given.
Press over 2sec. until 1 beep given.
Press over 2sec. until 1 beep given.
Press once
Press over 2sec. until 1 beep given.
Press over 2sec. until 1 beep given.
Press over 2sec. until 1 beep given.
Press over 2sec. until 1 beep given.
Engine running mode
Armed with safe status
Arming within 5sec.
ACC OFF
ACC ON
ACC OFF
ACC ON
Armed with safe status
Functions Step Condition
Remote button lock (on/off)
Vibrate mode on/off
Clock time adjust mode
Clock time engine start
Battery conserve mode
Press over 2sec. until 1 beep given.
Press over 2sec. until 1 beep given.
Press over 2sec. until 1 beep given.
Press over 4sec. until 2 beep given.
Press over 2sec. until 1 beep given.
Remote battery discharge/replacement
If the batterybecomes exhausted, the remote will emitextra long beep,While press any
button on theremote, few seconds later the indicatorwill flashing for identify.
The battery dischargeis displayed on the LCD screenas the iconwith the status indicator .
Also you canpay your attention that the effectivedistance for the transmitter is being
reduced.
To replace the batteries of 2-way remote
- Bend thetop part of the cover abit, move itup and remove,
- Remove thedischarged battery,
- Place thenew battery (AAA) observing polarity,
- Carefully placethe cover back.
To replace the batteries of 1-way remote
- Loose thescrews on the back side ofthe transmitter housingand separate two halves of
the transmitter housing,
- Remove thedischarged battery,
- Place thenew battery 12V 23A observingpolarity,
- Carefully placethe cover back (please do notdamage the LEDand switchers on the
Circuit board);
tighten the screwson the back side of thetransmitter housing.
Programming of codes for new transmitters
Important
Please notice that during the programming of a new transmitter into the system memory all
previous programmed codes of the transmitters will be erased so in case of programming
for additional transmittersthe available transmitters shall be programmed again.
The system supports in memory up to four codes of remotes irrespective of the fact if the
codes of fourdifferent remotes orthe same code four times isrecorded into the system.
Programming of newtransmitters.
Important
Please notice that each following operation shall be done within 10 sec after the previous
operation. If the 10 second period is over the system will automatically exit the
programming mode and two long chirps will acknowledge theexit. If the ignition is turned off
during programming the system will immediately exit the programming mode and two long
chirps will acknowledgethe exit.
1. Disarm the system.
2. Turn theignition from on to off.
3. Within 10 secafter switching offthe ignition pressand hold the Valet buttonover 3 sec ,
the LED startsflashing , release the Valetbutton.
4. Press and holdthe Valetbutton, you will hear the sirenstart chirping (from1~3 chirp),
while give 2chirp sound, immediately release the Valet button.
5. The LED willstart flashing to acknowledging that thesystem is ready for programming of
new transmitters.
6. Press any buttonof the first transmitter, youwill hear 1-shortchirp acknowledging that
the first transmitterhas been programmed
Press any buttonof the second transmitter, youwill hear 2-shortchirp acknowledging
that the secondtransmitter has been programmed.
Repeat the operation3 for other transmitters.
7. Toexit the transmitter programming mode, Turn on the ignition and youwill hear two long
siren chirps.
Indice
Altri manuali Eaglemaster Allarme auto
Eaglemaster
Eaglemaster E2 Manuale utente
Eaglemaster
Eaglemaster E5 Manuale utente
Eaglemaster
Eaglemaster AS-232T Manuale utente
Eaglemaster
Eaglemaster E5 G7 Manuale utente
Eaglemaster
Eaglemaster E1 Plus Manuale utente
Eaglemaster
Eaglemaster LT-6200 Manuale utente
Eaglemaster
Eaglemaster CA-168 Guida di sicurezza
Eaglemaster
Eaglemaster E4 Manuale utente
Manuali Allarme auto popolari di altre marche
Federal Signal Corporation
Federal Signal Corporation Pathfinder Siren Series Manuale
Falcon
Falcon Predator XL3 Guida utente
Audiovox
Audiovox Auto Security XR91 Istruzioni operative
Clifford
Clifford Sabre II Manuale utente
CrimeStopper
CrimeStopper CS-8717 Guida rapida
Ultra Start
Ultra Start 450 SERIES Manuale utente
