Easi-Dec Board-Walk Manuale utente
Board-Walk Assembly Instructions
SAFE RAPID ACCESS
Board-Walk Assembly Instructions
Before assembling the Board-Walk for the first time,
it is highly recommended that Installers familiarise
themselves with the component parts and carry out a
test assembly and disassembly in a safe area away
from the point of final installation. All component parts
detailed in the operating instructions must be used in
the assembly of the system. Should a piece be missing
or appear defective do not continue to assemble and
contact Easi-Dec Immediately.
IMPORTANT NOTE:
A. Lay out the components ready for assembly
B. Attach the first support batten to the underside of the
Board-Walk section using the captivated pins in the holes
in the stiles (mesh side is the top)
C. Repeat step B for the second batten D. Tie a strap or rope to the top rung of the Board-Walk
in preparation for lowering it onto the roof
The Board-Walk has been designed to allow temporary
access to be gained on fragile roof surfaces. It is not
designed to be permanently left on a roof. Prior to Board-
Walk being used on any roof surface, it is essential that:
1. The roof structure is checked to ensure it can take the
weight being applied.
2. A risk assessment is carried out and a method
statement is prepared.
3. The operative assembling the system must be
competent and fully trained in the use of the product and
work at height.
SAFETY REQUIREMENTS:
Board-Walk Assembly Instructions
G. Before stepping onto the Board-Walk insert the
second uprights into the batten and insert the pin
and ‘R’ clip required
H. Position the mid-rails over the upright posts taking
care not to stand on the Board-Walk at this stage.
I. Fit the top rails into position over the uprights and
tighten the grub screws.
E. Attach your restraint lanyard to the Easi-Dec platform
or a secure point before lowering the Board-Walk. Insert
the top uprights into the batten sockets and secure
with the pins and ‘R’ clips supplied.
F. With the strap / rope tied on securely lower the
Board-Walk panel onto the roof. You will need to repeat
these steps for further Board-Walk panels
Board-Walk Assembly Instructions
CONNECTING BOARD-WALK (A) CONNECTING TO THE SAFETY LINE CONNECTING BOARD-WALK (B)
WORKING FROM THE BOARD-WALK WORKING FROM THE BOARD-WALK
J. When connecting additional Board-Walk sections
together follow steps D & E in these instructions for
laying the Board-Walks into position.
K. Remember to connect onto the restraint safety line with
an adjustable lanyard. Remember to continually adjust the
adjustable lanyard to remain in a work restraint position.
L. Standing on the first Board-Walk, slide through the
locking pin. When the locking pin is in place secure with
the supplied ‘R’ clip. Repeat stages b-j to complete the
assembly of further board walk units to reach the desired
position
M. Where required a section of handrail can be removed.
To facilitate this safely ensure the operative is working in
restraint and suitably connected to the board walk re-
straint safely line.
N. Ensure at all times a work restraint position is
maintained in the absence of full handrail protection.
The short lanyard will stop you from over reaching and
allow you to work safely.
DISMANTLING THE BOARD-WALK
Simply follow the instrucons in reverse order to
safely dismantle a Board-walk installaon
Board-Walk Pre-Use Checks
Always carry out a risk assessment and method statement
Check the structure of the roof can take the loads being applied
Always ensure the area below where you are working is clearly marked to stop people from encroaching
Ensure the short lanyard will restrict you from leaning more than one arms length away from the boardwalk.
The safety line should be positioned on the opposite side of the Board-Walk to the working area.
Edge protection must be provided to comply with current working-at–height regulations and hierarchy of controls
Always clip onto the safety-line fixed to one side of the Board-Walk with a restraint lanyard
The maximum load capacity is 150kg per Board-Walk (this is subject to roof type, structure and survey)
Board-Walk Recertification
Periodic inspections by a competent person are required under the Temporary Work Equipment Directive 2009/104/EC –use of work equipment and Section 12
of the Work at Height Regulations. The frequency will depend upon environment, location and utilisation, but should be at least every 12 months or before and
after each use whichever soonest.
Visually inspect the complete system before installation ensuring all component parts are present.
Ensure the system has not been modified/tampered with by unauthorised persons.
DETAILED COMPONENT INSPECTION:-
Boardwalk Underside & Topside
Check complete frame for distortion, cracks or dents.
Check complete mesh for cracks, breaks and or missing rivets.
Ensure that the hand rail sockets are in good condition so that the fitting of handrails and pins are not affected.
Check safety line for wear & tears, breaks and ensure it is correctly secured to the boardwalk.
CHECK FOR ANY GENERAL CORROSION.
Battens
Check for any general corrosion.
Check the pins snap into position on their own accord and that they are not stuck in the open position.
Handrail
Check the top and mid rail for distortion or dents. Ensure all fittings are fitted to the rails and grub screws are in position.
Check the handrail upright posts for distortion, cracks or dents. Ensure that this does not affect the fitting of the pin assembly.
Check for any general corrosion.
General
Once all other inspection points are completed, check that the whole device is fixed securely in position with no obvious distortions in balance.
Always keep a log of all inspections and comments.
Kee Safety Ltd
Cradely Business Park
Overend Road
Cradely Heath
B64 7DW, UK
Phone: +44 (0) 1384 632 188
Fax: +44 (0) 1384 632 192
www.keesafety.co.uk
Indice
Altri manuali Easi-Dec Sensore di sicurezza
