EastLink ADC-V723 Manuale utente

DIY Smart Camera Guides

Table of contents

Outdoor Camera (ADC-V723) 2

Indoor Camera (ADC-V523/522) 3

Homeview Camera (ADC-V622) 3

Video Doorbell 4

How to Set up the Camera 6

Using the App for Alarm.com 6

Using the Web Portal for Alarm.com 6

Using AP Mode 6

Outdoor Camera (ADC-V723)

Pre-Install Check List:

• ADC-V723 Camera

• Mounting plate

• Power supply (10 feet)

• Wall anchors & screws (x2)

• Internet - Wireless (2.4 or 5GHz) or Ethernet connection

• Alarm.com login credentials

• A computer, tablet or smartphone with WiFi

Physical installation recommendations:

• In a shaded area or under cover (e.g., under an eave)

• Mounting bracket installed on a vertical surface

• Position the camera with a downward tilt

• SD card door facing downwards

• Power supply must be plugged inside

Reference the “How to Set Up the Camera” section on page 6 to set up the camera prior to

mounting the camera.

How to Mount the Camera:

The Outdoor Camera can be mounted outside, but it needs to be plugged inside. You’ll need to

drill holes into the wall to mount the Outdoor Camera. Use the longer screws that were included

with the camera if you’re drilling into wood, and we recommend using the anchors for stucco or

brick walls. You can then mount the camera body into the wall using the included screws.

To access the Camera mounting bracket:

1. Find the locked and unlocked icons on the base of the camera. The bottom half of the

base is the mounting bracket.

2. Twist counter-clockwise until the mark lines up with the unlocked icon.

3. Lift the camera away from the mounting bracket.

To reaach the Camera to its mounting bracket:

1. Line the mark up to the unlocked icon on the mounting bracket.

2. Twist clockwise until the mark lines up with the locked icon. The camera should

lock in place.

Indoor Camera (ADC-V523/522)

Pre-Install Check List:

• ADC-V522 or ADC-V523 Camera

• AC Power adapter

• Internet - Wireless (2.4 or 5GHz) or Ethernet connection

• Alarm.com login credentials

• A computer, tablet or smartphone with WiFi

Reference the “How to Set Up the Camera” section on page 6 to set up the camera before

moving on to mounting.

How to Mount the Camera:

The Indoor Camera can be mounted indoors by using its mounting bracket.

To access the Camera mounting bracket:

1. Find the locked and unlocked icons on the base of the camera. The bottom half of the

base is the mounting bracket.

2. Twist counter-clockwise until the mark lines up with the unlocked icon.

3. Lift the camera away from the mounting bracket.

To reaach the Camera to its mounting bracket:

1. Line the mark up to the unlocked icon on the mounting bracket.

2. Twist clockwise until the mark lines up with the locked icon. The camera should

lock in place.

Homeview Camera (ADC-V622)

Pre-Install Check List:

• ADC-V622 camera

• AC power adapter

• Internet - Wireless (2.4 or 5GHz) or Ethernet connection

• Alarm.com login credentials

• A computer, tablet or smartphone with WiFi

Reference the “How to Set up the Camera” section on page 6 to ﬁnish seing up the camera.

Video Doorbell

Pre-Install Check List:

• Slim Line WiFi Doorbell Camera (ADC-VDB105/106) or SkyBell HD WiFi Doorbell

Camera (ADC-VDB101/102)

• Wall mounting bracket

• Wall screws

• Masonry anchors

• Internet - Wireless (2.4 or 5GHz)

• Alarm.com login credentials

• A computer, tablet or smartphone with WiFi

Important:

• The video doorbell is only compatible with existing wired doorbells.

• Upload speed minimum of 2 mbps where the video doorbell will be installed is required.

• The mounting plate afﬁxes to a ﬂat surface and uses the existing doorbell wiring.

• You may need a power drill to complete this install.

Pre-Install Assessment:

Wired Doorbell:

Verify the existing wired doorbell is working and visually inspect the doorbell button for wires. If

necessary, you can remove the doorbell from the wall to check for wiring.

Note: If there is a power issue or the doorbell does not ring indoors, the issue must be resolved

before installing the video doorbell.

Visually inspect the doorbell button for wires. You can also inspect inside the home – the chime

plugged into a power outlet may indicate an incompatible doorbell system is present.

Chime:

Locate the chime inside the home and remove the faceplate. Identify if the chime is compatible:

Compatible:

• Mechanical: metal bars and a striker pin.

• No Chime: you will only get alerts on your phone.

Incompatible (may require additional hardware):

• Digital: a speaker that plays a tone when pressed (will require a digital doorbell

adapter and enabling to the digital doorbell setting to work in the app).

• Tube Chime: series of tubular bells and is incompatible with the video doorbell.

• Intercom system: button ﬁxture includes a speaker that is incompatible with the

video doorbell.

Internet Speed:

1. Go to the location where the Video Doorbell will be installed.

2. Connect to the 2.4 GHz WiFi network.

3. Run an Internet speed test to determine the Internet speed.

4. In the test results, note the Upload speed. The Video Doorbell requires an

upload speed of at least 2 Mbps.

Hardware Install:

1. Remove existing doorbell – ensure the wires don’t slip into the wall.

2. Attach doorbell mounting bracket to the wall.

a. Feed the wires through the hole in the centre of the bracket.

b. Mount the bracket ﬁrmly with the wall screws (provided) through the top &

bottom holes in the bracket.

c. Failure to make the bracket ﬂush on the wall could cause a poor power connection.

3. Connect power wires to the mounting bracket.

a. Loosen terminal screws and insert wires beneath the screws – be careful not to

touch the wires together during this process.

b. Tighten the screws so the screw heads are ﬂush with the bracket.

c. The wires must be approximately equal thickness.

4. Attach the Video Doorbell to the mounting bracket.

a. Slide the Video Doorbell down on to the mounting bracket and push the front

toward the wall.

b. Tighten the set screw located on the bottom of the camera (be careful not to

damage it – do not use a power tool for this step).

c. The camera’s LED light should light up.

5. Syncing with Alarm.com

a. The Video Doorbell is ready to sync when the LED light is alternating red & green – this

means it is ready to use AP mode.

Reference the “How to Set up the Camera” section on page 6 to ﬁnish seing up the camera.

How to Set up the Camera

Using the App for Alarm.com

1. Download the Alarm.com app to your smartphone.

a. If you are already have the app, please make sure it is the latest version.

2. Log into the app.

3. Tap the navigation menu icon . On a computer or tablet, go to “Seings”.

4. Select “Add Device”.

5. Select “Video Camera”.

6. Select the camera model you wish to set up (if it does not appear, please follow the

AP Mode instructions).

7. Follow the instructions on screen to set up the camera.

8. Now you’re ready to mount or place the camera in your preferred location.

Using the Web Portal for Alarm.com

1. Login to the Web Portal - Alarm.com/login.aspx.

2. Click “Seings”.

3. Select “Add Device”.

4. Select “Video Camera”.

5. Select the camera model you wish to set up (if it does not appear, please follow the

AP Mode instructions).

6. Follow the instructions on screen to set up the camera.

7. Now you’re ready to mount or place the camera in your preferred location.

Using AP Mode

Important: To ensure sufﬁcient WiFi signal, complete these steps with the camera near its ﬁnal

location but prior to mounting.

1. Connect the camera’s AC power adapter and plug it in to a non-switched outlet.

2. The camera’s LED light will begin to ﬂash white. If it does not ﬂash white, hold down the

reset button and release when the LED light begins to ﬂash white (about 6 seconds).

3. On a WiFi enabled device (smartphone, computer, tablet), connect to the WiFi network

AD-V723 (XX:XX:XX) where XX:XX:XX is the last 6 digits of the camera’s MAC address

(located on bottom of camera and packaging).

4. On the same device, open a web browser and enter www.alarm.com/addcamera in the

URL ﬁeld.

5. Follow the instructions on screen to add the camera to the WiFi Network.

a. Click “Scan” – you will see a box asking for SSID and Password.

b. Click to select your WiFi network and the SSID ﬁeld will automatically populate

with your network name.

c. In the password ﬁeld, put in the password for your WiFi network.

d. Click “Submit” and the LED light on the camera will ﬂash solid green.

6. Add the camera to your account by using the App or Web Portal instructions above.

eastlink.ca

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali EastLink Telecamera IP

EastLink

EastLink ADC-V622 Manuale utente

Manuali Telecamera IP popolari di altre marche

FLIR

FLIR Exx series Manuale utente

Avigilon

Avigilon H4A-BO1-IR Manuale utente

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuale utente

ShareTech

ShareTech AV1 Manuale utente

Ezviz

Ezviz C6C Manuale utente

Melchioni

Melchioni UCAM 2015 Manuale utente

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuale utente

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuale utente

Mitel

Mitel 6800i Series Manuale di servizio

Vitek

Vitek VTC-IR403-212NP Manuale utente

THOMSON

THOMSON DSC - 323W Manuale utente

AVer

AVer FB2027 Manuale utente

ENFORCER

ENFORCER EV-T5105-N2SQ Manuale utente

Wansview

Wansview NC543 Manuale utente

Eneo

Eneo MCB-64A0003M0A Manuale utente

deView electronics

deView electronics CBDNI36F Manuale utente

Swann

Swann SwannEye Manuale utente

LevelOne

LevelOne IP CamSecure Manuale utente