Eaton ELC-485APTR Manuale utente

IL05003022E.pdf

ELC-485APTR

RS-485 Interface Adpater

Instruction sheet

1 WARNING

ELC-485APTR is an OPEN-TYPE. Please place the module in an enclosure away from airborne dust or high humidity

and prevent electric shock or sudden collision on ELC-485APTR. Also, it is equipped with protective methods such as

some special tool or key to open the enclosure, so as to avoid the hazard to users or any damage to the module. Do

NOT touch terminals when power on.

I/O terminal screws should be tightened to between 1.95 kg-cm (1.7 in-lbs). Use copper conductor only, 60 oC / 75oC.

2 INTRODUCTION

ELC-485APTR is mainly designed to connect Eaton product by RS-485 interface. It is equipped with surge absorber and

limited current protection to ensure safe connection of different devices. Also, a switch enabled built-in terminator (120Ω).

Environmental Specification:

Operation 0℃~55℃(Temperature), 50~95%(Humidity), pollutant degree 2

Storage -25℃~70℃(Temperature), 5~95%（Humidity）

Vibration/Shock resistance International Standard: IEC1131-2, IEC 68-2-6（TEST Fc）/ IEC1131-2 & IEC 68-2-27 (TEST Ea)

Product profile:

106,8

32 660

3,4

Units: mm

Fig. 1: Profile and Dimensions

1. Mounting plate

2. COM 1 (DB9 female)

3. COM 2 (DB9 male)

4. Nameplate

5. ON/OFF of termination resistor (factory

setting: OFF)

6. DIN rail (35mm)

7. RS-485 port

8. RJ12 port

3 ELC-485APTR Connection with Eaton Products

Connection of ELC-485APTR and AC Motor Drive (please see AC motor drive user manual for detail information)

MVX 9000

RS-485 Network

Fig. 2: ELC controller connection with MVX9000

IL05003022E.pdf

Compact Installation reference:

See Fig. 3a in lower left, when ELC-485APTR is separated from mounting plate, it can be used as the last extension module

with its RS-485 port connecting to ELC controller’s (see Fig. 3b for illustration). This connection is feasible for ELC controller to

connect AC Motor Drive within 5 meters.

MVX 9000

ELC-EX08NNDN

RS-232

RS-485

x16

ELC-PC12NNDR

STOP

RUN

x16

ELC-COPBDP

Fig. 3a Fig. 3b

PIN Explanation of COM1, COM2, and RJ12

COM1-DB9 female PIN Definition

RJ12 of AC Motor Drive side PIN Definition

1 RS485- 1 +15V

2 RS485+ 2 GND

3 RS485+ 3 SG-

4 RS485- 4 SG+

5~9 NC

5, 6 Reserved

COM2-DB9 male PIN Definition

RJ12 of ELC-485APTR side PIN Definition

3, 6 RS485- 3 RS-485+

8 RS485+ 4 RS-485-

5, 9 GND 5 GND

1, 2, 4, 7 NC 1, 2, 6 NC

4 ELC-485APTR Termination Resistor Application

In all RS-485 installations, the cable must be correctly terminated with two sets of resistors, one set at each end of the network

(4,000 feet maximum total cable length). This applies even if you are only using one slave node connected to one master

device. The terminating resistors prevent reflection problems that can interfere with data transmission. The resistance value of

the terminating resistors should match the characteristic impedance of the cable. A typical value is 120 ohms. The terminating

resistors must be placed at the two farthest ends of the RS-485 network, regardless of where the master device is. In some

cases master device RS-485 ports have built in or optional terminating resistors. Beware of your network (whether it has one

node or 32 nodes) having only two sets of terminating resistors.

ELC-485APTR’s Termination Resistor Switch is located inside of the

adapter’s extension port.

Switch ON the termination resistor for ELC-485APTR on the both ends only

and switch OFF (factory setting) for the modules between both ends when

modules are connecting in parallel.

Termination Resistor Switch

Fig. 4

Indice

Altri manuali Eaton Adattatore

Eaton

Eaton PowerXL DX-NET-ETHERCAT-2 Manuale utente

Eaton

Eaton Cutler-Hammer APPS12A Manuale utente

Eaton

Eaton xComfort CEMP Series Manuale utente

Eaton

Eaton ELC-CAENET Manuale utente

Eaton

Eaton Cutler-Hammer RSS 36-SD-ST Manuale utente

Eaton

Eaton ConnectUPS Web/SNMP Card Manuale di programmazione

Eaton

Eaton SWD4-FFR-PF1-1 Manuale

Eaton

Eaton EBT 01 Manuale utente

Eaton

Eaton HALOHOME HWAD1BLE40AWH Manuale utente

Eaton

Eaton Cutler-Hammer APFP15A Manuale utente

Eaton

Eaton xComfort CHVZ-01/04 Manuale

Eaton

Eaton XT-RJ45-ETH-RS232 Manuale

Eaton

Eaton AQB-L400 Manuale utente

Eaton

Eaton TRIPP LITE U444-06N-HU-C Manuale utente

Eaton

Eaton TRIPP LITE U209-30N-IND Manuale utente

Eaton

Eaton Quick Connect Manuale utente

Eaton

Eaton TRIPP LITE Series Manuale utente

Eaton

Eaton Power Defense PDC9-ETU Manuale

Eaton

Eaton PXGMS Power Xpert Gateway Minislot UPS Manuale di programmazione

Eaton

Eaton xComfort CDAP-01 Series Manuale utente

Eaton

Eaton TRIPP LITE U209-30N-IND Manuale utente

Eaton

Eaton SKF-HA Manuale

Eaton

Eaton xComfort CSAP-01 Series Manuale

Eaton

Eaton TRIPP LITE U209-005-DB25 Manuale utente

Manuali Adattatore popolari di altre marche

PCB Piezotronics

PCB Piezotronics 090B274 Manuale utente

Auvidea

Auvidea J20 Manuale del prodotto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuale utente

Akribis

Akribis ITF-21-BISS-MIT Manuale utente

Tenda

Tenda W54U Manuale utente

ROHO

ROHO AGILITY Manuale utente

PROLiNK

PROLiNK WN2001 Manuale utente

Hawking

Hawking HUF2 Manuale utente

Airlink101

Airlink101 AWLC4030 Manuale utente

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuale utente

Philips

Philips SWA4554S/10 Manuale utente

JVC

JVC TS-C9D2B Manuale di istruzioni

NETGEAR

NETGEAR A6100 Manuale utente

D-Link

D-Link DWA-121 Manuale utente

Philips

Philips SWA2037 Manuale utente

Basalte

Basalte 0610-20 Manuale utente

Yealink

Yealink EHS40 Manuale utente

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuale utente