Eaton ELC-COENETM Manuale utente

ELC-COENETM Effective December 2010

Users Manual

ELC-COENETM

MN05006001E For more Information visit: www.eaton.com 1

Introduction

3This is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne

dust, excessive humidity, shock and vibration. The enclosure should prevent non-maintenance

staff from operating the device (e.g. key or specific tools are required to open the enclosure) to

avoid potential equipment damage or personal injury. DO NOT touch any terminal when the power

is switched on.

3Please read this manual carefully and follow the instructions to avoid damage to the product or

personal injury.

Table of Contents

1Introduction..............................................................................................................................3

2Specification ............................................................................................................................3

3Product Profile and Outline....................................................................................................4

4Installation and Wiring............................................................................................................5

5Configuring and applying the ELC-COENETM using ELCSoft (V2.0 or later)...................6

5.1 Connecting the PC to the ELC-COENETM through a LAN.........................................7

5.2 Changing the ELC-COENETM module name and IP address settings......................9

5.3 Setting up and Clearing a Password ..........................................................................10

5.4 Recovering from a lost password............................................................................... 11

5.5 Setting IP Filter Protection to restrict access............................................................12

5.6 Setting up E-Mail notification ......................................................................................14

5.7 Setting up Data Exchange between ELC processors ...............................................15

5.8 Setting up Data Exchange from ELC processor to any Modbus TCP servers.......21

5.9 Setting up Data Exchange between ELC processor to other Modbus TCP clients22

5.10 Setting up Data Exchange with an ELC Remote I/O Adapter (ELC-CAENET) ........25

6CR Definitions for ELC-COENETM ......................................................................................34

Microsoft® and Windows Internet Explorer® are the registered trade mark or trade mark

of Microsoft Corporation in the United States and other countries.

Java® is the registered trade mark or trade mark of Sun Microsystems, Inc. in the United

States or other countries.

ELC-COENETM

2 For more Information visit: www.eaton.com MN05006001E

The companies and products mentioned in this operation manual can be the trade mark

possessed by the owner of that trade mark right.

ELC-COENETM

MN05006001E For more Information visit: www.eaton.com 3

1 Introduction

The ELC-COENETM is an Ethernet communication module for remote configuration,

monitoring and control. It` supports the `Modbus TCP communication protocol as both a client

and server device. Acting as a server device, the ELC-COENETM provides remote monitoring

from SCADA (Supervisor Control and Data Acquisition) software or HMI (Human Machine

Interfaces) panels.Acting as a client device, the ELC-COENETM can poll server devices such

as VFDs and remote I/O products for use in the ELC control program.

In addition to Modbus TCP support, the ELC-COENETM module allows the ELC control

program to be remotely monitored and updated from ELCSoft or EIPSoft over Ethernet. It also

provides email support for event notification and provides for ELC clock synchronization from

an NTP server.

Features

zSupports MODBUS TCP

zSupports Master and Slave Data Exchange

zELC-PV28NNDR/TAutomatic Time Correction

zSupports E-Mail

zRS-232/Ethernet Configuration

zTransmission Speed: 10/100 Mbps

2 Specification

Functions Specification

Network Interface

Interface RJ-45 with Auto MDI/MDIX

Number of ports 1 Port

Transmission

method IEEE 802.3, IEEE 802.3u

Transmission cable Category 5e (TIA/EIA-568-A,TIA/EIA-568-B)

Transmission Rate 10/100 Mbps Auto-Detect

Protocol ICMP, IP, TCP, UDP, DHCP, SMTP, NTP, MODBUS TCP

Serial Interface

Interface RS-232

Number of Ports 1 Port

Transmission Cable ELC-CBPCELC3

Electrical Specification

Power supply

voltage 24VDC (-15% ~ 20%) (Power is supplied by the internal bus of

MPU)

Power Consumption 1.5W

ELC-COENETM

4 For more Information visit: www.eaton.com MN05006001E

Noise Immunity

ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2KV,

Communication I/O: 1KV

Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV

RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m

Insulation voltage 500V

Vibration/Shock

Immunity Standard: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC

68-2-27 (TEST Ea)

Operation/storage

temperature

Operation: 0°C ~ 55°C (temperature), 50 ~ 95% (humidity),

pollution degree 2;

Storage: -25°C ~ 70°C (temperature), 5 ~ 95% (humidity)

Certificates , Operating temperature code: T5

Weight (g) 92 (g)

3 Product Profile and Outline

LAN

100M

RS-232

LNK

POWER

RS-232

1. POWER, LINK, RS-232, 100M LED 2. Extension Port to connect Extension

modules

3. Extension clip 4. Extension hole for mounting unit or

module

5. Extension Port to connect I/O Modules 6. RS-232 port

7. Ethernet RJ-45 port 8. DIN rail clip

LED indicators

Indicator Color Indication

POWER Green Power indication

RS-232 Red Communication status for the serial port

100M Orange Network connection status

LINK Green Network communication speed

ELC-COENETM

MN05006001E For more Information visit: www.eaton.com 5

RJ-45 PIN definition

RJ-45 sketch Terminal No. Definition Explanation

1 Tx+ Positive pole for data transmission

2 Tx- Negative pole for data transmission

3 Rx+ Positive pole for data receiving

6 Rx- Negative pole for data receiving

4, 5, 7, 8 - N/C

Dimension

ELC-COENETM

60 33

Unit: mm

4 Installation and Wiring

How to Connect the ELC-COENETM with the ELC processor

zOpen the extension clips on the left side of the MPU.

zConnect the extension port of the ELC controller to the ELC-COENETM as shown

below.

zClose the extension clips.

RS-232

00M

OWER

ELC-COENETM

6 For more Information visit: www.eaton.com MN05006001E

Installing the ELC-COENETM With Other Extension Modules

To connect ELC-COENETM with other extension modules, lift the extension clips of the

extension module with a screwdriver and remove the side cover. Connect the second

ELC-COENETM as described above. A maximum of 8 left side communication modules are

supported.

Connecting the ELC-COENETM to the network

zConnect ELC-COENETM to the Ethernet switch using a standard CAT-5e cable.

ELC-COENETM providesAuto MDI/MDIX function; therefore, ELC-COENETM does

not need to use a cross over cable for direct connection to a PC.

zA typical Network connection between the PC and ELC-COENETM is shown below:

5 Configuring and applying the ELC-COENETM using ELCSoft (V2.0 or

later)

ELCSoft integrates the capabilities to configure the ELC-COENETM module in the same

programming environment used to generate your ELC control program. The following settings

are described in this section:

Ethernet

PC Maste

DVP28SV

RS-232

INK

00M

DVPEN01

OWER

ELC-P

COENET

DVP28SV

RS 232

RS-232

00M

DVPEN01

OWER

ELC-PV

COENET

ELC-COENETM

MN05006001E For more Information visit: www.eaton.com 7

zEstablishing communications between ELCSoft and the ELC-COENETM module

zAssigning a new module name and network settings for the module

zSetting up and clearing password protection

zRecovering from a lost password

zSetting IP Filter Protection to restrict access

zSetting up email notification

zSetting up data exchange between ELC processors (continuous exchange)

zSetting up data exchange with any Modbus TCP server

zSetting up data exchange with any Modbus TCP client

zSetting up data exchange to an ELC remote I/O communications adapter

(ELC-CAENET)

5.1 Connecting the PC to the ELC-COENETM through a LAN

(1) Connect the PC running ELCSoft and the ELC-COENETM to a common LAN. A direct

RJ cable connection can also be used

ELC-PV28NNDT

ELC-COENETM

ELC-PV28NNDT

ELC-CONENETM

(Note: the default IP address setting for the ELC-COENETM module is IP address =

192.168.1.5. The PC IP address and network mask need to be set up to reside on the

same network as the ELC-COENETM)

(2) Open “Communication Setting” in ELCSoft.

(3) Select “Ethernet” and press “OK”.

ELC-COENETM

8 For more Information visit: www.eaton.com MN05006001E

(4) Click the “Auto-Search” icon to search for all ELC-COENETM modules on the network.

Follow “View ÆWorkspace ÆCommunication” or “View ÆWorkspace ÆProject” to find

the detected ELC-COENETM modules (default module name: EATON ELC-COENETM,

IP: 192.168.1.5) in the window.

(5) Select the ELC-COENETM and double click it to open the setup page. All further

ELC-COENETM configuration is done through the setup page

Altri manuali per ELC-COENETM

Indice

Altri manuali Eaton Unità di controllo

Eaton

Eaton Vickers SF4-140-20-002-10 Manuale utente

Eaton

Eaton ELC-PC12NNDR Manuale utente

Eaton

Eaton HMi VU Series Manuale

Eaton

Eaton Crouse-hinds series Manuale utente

Eaton

Eaton XIOC-NET-DP-M Manuale

Eaton

Eaton OPTCB RS-485 Manuale utente

Eaton

Eaton CMA Manuale utente

Eaton

Eaton Powerware Series Manuale utente

Eaton

Eaton Transformer 5000 Manuale utente

Eaton

Eaton Eaton 5PX Istruzioni per il montaggio

Eaton

Eaton Crouse-hinds series Manuale utente

Eaton

Eaton EC4E-221-6D4T1 Manuale utente

Eaton

Eaton XTPAXENCS65B Manuale

Eaton

Eaton Cutler-Hammer Digitrip RMS 510 Manuale

Eaton

Eaton EP Control Manuale utente

Eaton

Eaton CEAG DLS/3PH-BUS-Module-inverse Manuale di servizio

Eaton

Eaton Moeller SL7-CB Series Manuale

Eaton

Eaton Cutler Hammer PanelMate ePro 7685 8 Series Manuale utente

Eaton

Eaton C441R Manuale utente

Eaton

Eaton xComfort CAEE-02/01 Manuale utente

Eaton

Eaton Vickers CM2 Series Manuale utente

Eaton

Eaton ELC-MC01 Manuale utente

Eaton

Eaton Cuttler-Hammer Pow-R-Command 100 Manuale

Eaton

Eaton PowerXL DE1 series Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente

Flyron

Flyron FN-BC04 Manuale utente