Eaton 5P1000RC Manuale utente

Page 1

ENGISH

5P 750VA -1.5 KVA EU_EN

Installation and

user manual

5P750RC

5P1000RC

5P1500RC

Page 2

5P 750VA-1.5 KVA US_EN

Certification Standards

Uninterruptible power systems (UPS) directives:

•IEC 62040-1: General and safety requirements for UPS

•IEC 62040-2: Electromagnetic compatibility (EMC) requirements

•IEC 62040-3: Method of specifying the performance and test requirements

. IEC 62040-4: Environmental aspects - Requirements and reporting

CE mark

CE compliance contact: Eaton I.F. – 110 rue Blaise Pascal – 38330 Montbonnot Saint Martin - France

The EC Declaration of Conformity is available upon request for products with a CE mark.

For copies of the EC Declaration of Conformity, contact Eaton Power Quality or check Eaton website:

www.powerquality.eaton.com

Class B emission level CISPR 22(EN 55022)

Harmonics emission: IEC 61000-3-2

Flickers emission: IEC 61000-3-3

FCC 47 CFR Part 15, Subpart B - Unintentional Radiators Class B

Special symbols

The following are examples of symbols used on the UPS or accessories to alert you to important

information:

RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol.

Important instructions that must always be followed.

Do not discard the UPS or the UPS batteries in the trash.

This product contains sealed lead acid batteries and must be disposed as it's explain in this manual.

For more information, contact your local recycling/reuse or hazardous waste center.

This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE)

in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.

Information, advice, help.

Page 4

5P 750VA-1.5 KVA US_EN

Safety of Persons

Product Safety

Special Precautions

•The system has its own power source (the battery). Consequently, the power outlets may be energized

even if the systems is disconnected from the AC power source.

•Dangerous voltage levels are present within the system. It should be opened exclusively by qualified

service personnel.

•The system must be plugged to an earthed outlet.

•The battery supplied with the system contains small amounts of toxic materials.

To avoid accidents, the directives listed below must be observed:

-servicing of batteries should be performed or supervised by personnel knowledgeable about batteries

and the required precautions.

-when replacing batteries, replace with the same type and number of batteries or battery packs.

-do not dispose of batteries in a fire. The batteries may explode.

-batteries constitute a danger (electrical shock, burns). The short-circuit current may be very high.

Precautions must be taken for all handling:

•Wear rubber gloves and boots.

•Do not lay tools or metal parts on top of batteries.

•Disconnect charging source prior to connecting or disconnecting battery terminals.

•The UPS connection instructions and operation described in the manual must be followed in the indicated

order.

•A protection circuit breaker must be installed upstream and be easily accessible. The system can be

disconnected from the AC power source by unplugging the input cable.

•Check that the indications on the rating plate correspond to your AC powered system and to the actual

electrical consumption of all the equipment to be connected to the system.

•For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be easily

accessible

•Never install the system near liquids or in an excessively damp environment.

•Never let a foreign body penetrate inside the system.

•Never block the ventilation grates of the system.

•Never expose the system to direct sunlight or source of heat.

•If the system must be stored prior to installation, storage must be in a dry place.

•The admissible storage temperature range is -15 to +50 °C / 5 to 122 °F.

•The system is not for use in a computer room.

•All handling operations will require at least two people (unpacking, installation in rack system).

•Before and after the installation, if the UPS remains de-energized for a long period, the UPS must be

energized for a period of 24 hours, at least once every 6 months (for a normal storage temperature less

than 25 °C / 77 °F). This charges the battery, thus avoiding possible irreversible damage.

•During the replacement of the Battery Module, it is imperative to use the same type and number of

element as the original Battery Module provided with the UPS to maintain an identical level of

performance and safety. In case of doubt, don't hesitate to contact your EATON representative.

Page 4

5P 750VA-1.5 KVA US_EN

1. Introduction .................................................................................5

1.1 Environmental protection .............................................................5

2. Presentation.................................................................................6

2.1 Standard installations..................................................................6

2.2 Rear panel ...............................................................................7

2.3 Control panel............................................................................8

2.4 LCD description .........................................................................9

2.6 User settings........................................................................... 10

3. Installation................................................................................ 12

3.1 Unpacking and contents check ..................................................... 12

3.2 Battery module connection ......................................................... 13

3.3 Rack installation...................................................................... 14

3.4 Wall mounting of rack model ....................................................... 15

3.5 Communication ports ................................................................ 16

4. Operation .................................................................................. 17

4.1 Start-up and Normal operation ..................................................... 17

4.2 Starting the UPS on Battery......................................................... 17

4.3 UPS Shutdown......................................................................... 17

4.4 Operation on Battery Power ........................................................ 17

4.5 Return of AC Input Power ........................................................... 18

4.6 UPS remote control functions....................................................... 18

5. Maintenance............................................................................... 19

5.1 Troubleshooting....................................................................... 19

5.2 Battery-module replacement ....................................................... 20

6. Appendices ................................................................................ 21

6.1 Technical specifications ............................................................. 21

6.2 Glossary................................................................................ 22

Page 4

5P 750VA-1.5 KVA US_EN

1. Introduction

Thank you for selecting an EATON product to protect your electrical equipment.

The 5P range has been designed with the utmost care.

We recommend that you take the time to read this manual to take full advantage of the many features of your

UPS (Uninterruptible Power System).

Before installing your 5P, please read the booklet presenting the safety instructions. Then

follow the indications in this manual.

To discover the entire range of EATON products and the options available for the 5P range, we invite you to visit our

web site at www.eaton.com/powerquality or contact your EATON representative.

1.1 Environmental protection

EATON has implemented an environmental-protection policy. Products

are developed according to an eco-design approach.

Substances

This product does not contain CFCs, HCFCs or asbestos.

Packing

To improve waste treatment and facilitate recycling, separate the various packing components.

•The cardboard we use comprises over 50% of recycled cardboard.

•Sacks and bags are made of polyethylene.

•Packing materials are recyclable and bear the appropriate identification symbol 01

PET

Materials Abbreviations Number in 01

the symbols PET

Polyethylene terephthalate PET 01

High-density polyethylene HDPE 02

Polyvinyl chloride PVC 03

Low-density polyethylene LDPE 04

Polypropylene PP 05

Polystyrene PS 06

Follow all local regulations for the disposal of packing materials.

End of life

EATON will process products at the end of their service life in compliance with local regulations. EATON

works with companies in charge of collecting and eliminating our products at the end of their service life.

Product

The product is made up of recyclable materials.

Dismantling and destruction must take place in compliance with all local regulations concerning waste. At the end

of its service life, the product must be transported to a processing center for electrical and electronic waste.

Battery

The product contains lead-acid batteries that must be processed according to applicable local regulations

concerning batteries.

The battery may be removed to comply with regulations and in view of correct disposa

Page 6

5P 750VA-1.5 KVA US_EN

2. Presentation

2.1 Standard installations

Rack model

Description Weights

(kg/lb)

Dimensions (mm/inch)

D x W x H

5P750RC 14.1/31.1 370*440*86.2 / 14.6*17.3*3.4

5P1000RC 15.0/33.1 370*440*86.2 / 14.6*17.3*3.4

5P1500RC 18.4/45.5 370*440*86.2 / 14.6*17.3*3.4

Page 7

5P 750VA-1.5 KVA US_EN

2.2 Rear panel

5P750RC & 5P1000RC & 5P1500RC

Attached 1.8 m input power cord for AC

power source

2) Slot for optional communication card

3) Primary group : Outlets for connection

of critical equipment

4) Group 1: programmable outlets for

connection of equipment

5) Group 2: programmable outlets for

connection of equipment

6) RS232 communication port

7) USB communication port

8) Connector for ROO (remote ON/OFF) or

RPO (Remote Power Off) control

①

②

③

④

⑥

⑦

⑧

⑤

Page 8

5P 750VA-1.5 KVA US_EN

ENGLISH

2.3 Control panel

The UPS has a five-button graphical LCD. It provides useful information about the UPS itself, load status,

events, measurements and settings.

100%

19min

1EBM

The following table shows the indicator status and description:

Indicator

Status

Description

Gree

The UPS is operating normally

Orange

The

UPS is on Battery mode.

The

UPS has an active alarm or fault. See trouble- shooting in

section 5.1

for additional information.

Page 9

5P 750VA-1.5 KVA US_EN

2.4 LCD description

As default, or after 5 minutes of inactivity, the LCD displays the screen saver.

The backlight LCD automatically dims after 10 minutes of inactivity. Press any button to restore the screen.

The following table describes the status information provided by the UPS

Note: If other indicator appears, see troubleshooting on section 5.1 for additional information.

Operation status Cause Description

Standby mode

The UPS is Off, waiting for start- up

command from user. Equipment is not powered until

button is pressed.

Online mode

The UPS is operating normally.

The UPS is powering and protecting

the equipment.

In AVR mode

beep every 10 seconds

The UPS is operating normally but

the utility voltage is outside

normal mode thresholds.

The UPS is powering the equipment

through a Automatic Voltage

Regulation device.

The equipment is still normally

protected.

On Battery

Battery LED is on

1 beep every 10 seconds

A utility failure has occurred and

the UPS is in Battery mode.

The UPS is powering the equipment

with the battery power. Prepar

e your

equipment for shutdown.

End of backup time

1 beep every 3 seconds

The UPS is in battery mode and

the battery is running low.

This warning is approximate, and

the actual time to shutdown may

vary significantly.

Depending on the UPS Load, the

"Battery Low" warning may occur

before the battery reaches 20 %

capacity.

Page 10

5P 750VA-1.5 KVA US_EN

ENGLISH

2.5 Display functions

Press the Enter () button to activate the menu options. Use the two middle buttons ( and ) to scroll through the

menu structure. Press the Enter ( ) button to select an option. Press the button to cancel or return to the

previous menu.

Main menu

Submenu

Display information or Menu function

Measurements

Load W VA / Load A pf / Output V Hz / Input V Hz /

Battery V min / Efficiency / Power usage

Control

Load Segments

Group 1: ON / OFF

Group 2: ON / OFF

These commands overrule user settings for load segments.

Start battery test

Starts a manual battery test

Reset fault state

Clears active faults

Restore factory settings Returns all settings to original values (UPS restart required)

Reset power usage

Clears power usage measurements

Settings

Local settings

Sets product general parameters

In/Out settings

Sets Input and Output parameters

On/Off settings

Sets On/Off conditions

Battery settings

Sets battery configuration

Fault log

Fault list

Displays the faults stored

Reset fault list

Clears faults

Identification

UPS Type / Part Number / Serial Number / Firmware release /

Com card address

2.6 User settings

The following table displays the options that can be changed by the user.

Submenu

Available settings

Default settings

Local settings

Language

[English] [Français] [Deutsch] [Español]

[Русский] [Português] [Italiano]

[Simplified Chinese] [Japanese]

Menus, status, notices and alarms, UPS

fault, Event Log data and settings are in

all supported languages.

[English]

User selectable when UPS is

powered for the first time.

LCD settings

Modify LCD screen brightness and

contrast to adapt to room light

conditions .

Audible alarm

[Enabled] [Disabled on battery]

[Always disabled]

Enable or disable the buzzer if an

alarm occurs.

Enable

In/Out settings

Output voltage

[100V] [120V] [125V]

User selectable when UPS

is powered for the first time

Input thresholds

[Normal mode] [Extended mode]

Extended mode reduces lower

input voltage to 150 V before UPS

transfers to battery.

Normal mode

Sensitivity

[High] [Low]

High: for sensitive equipment, UPS will

easily transfer to battery when utility

conditions are becoming bad.

High

Load segments -

Auto start delay

[No Delay] [1 s] [2 s]… [65354 s] The

connected load is powered after the

specified delay.

Group 1: 3 s

Group 2: 6 s

Load segments

Auto shutdown

delay

[Disable] [0s] [1 s] [2 s]…[65354 s]

During a power outage, authorises

to keep some equipment running

while turning off other equipment.

Group 1: Disable

Group 2: Disable

Overload prealarm

[10 %] [15 %] [20 %] ... [100 %]

[105 %]

Gives a warning when a predefined

critical percentage of load is

[105 %]

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Eaton UPS

Eaton

Eaton Powerware 9355 Manuale utente

Eaton

Eaton Ellipse PRO 1600 FR Manuale utente

Eaton

Eaton Powerware 9390 Manuale utente

Eaton

Eaton UPS 225275 kVA Powerware 9395 Guida alla risoluzione dei problemi

Eaton

Eaton Powerware 9355 Manuale utente

Eaton

Eaton Ellipse ECO 800VA DIN Manuale utente

Eaton

Eaton 93E G2 100/100 Manuale

Eaton

Eaton 93PM IBC-L Manuale utente

Eaton

Eaton Powerware 9395 550 kVA MBM Manuale utente

Eaton

Eaton EX 700 Manuale utente

Eaton

Eaton Powerware 5115A USB Manuale utente

Eaton

Eaton EX Pulsar Series Manuale utente

Eaton

Eaton Powerware 9155 Manuale utente

Eaton

Eaton Powerware 9155 Manuale utente

Eaton

Eaton 5E700UD-KR Istruzioni per il montaggio

Eaton

Eaton 5P 1550G RL Manuale utente

Eaton

Eaton Ellipse ASR 450 Manuale utente

Eaton

Eaton 5SC 1500G Manuale utente

Eaton

Eaton Pulsar Series Manuale utente

Eaton

Eaton 9PXM Manuale utente

Eaton

Eaton Powerware 9355 Manuale utente

Eaton

Eaton Power Xpert 9395P-1100/1100 Manuale utente

Eaton

Eaton Powerware 9390 Manuale utente

Eaton

Eaton 9E Manuale utente

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente

ZincFive

ZincFive BC Series Manuale utente