Eaton Powerware 9170+ Manuale utente
Powerware Series
Eaton 9170+Rail Kit
9- and 12-Slot Cabinets
Installation Guide
®
Eaton and Powerware are registered trademarks of Eaton Corporation or its subsidiaries and affiliates. Phillips is a
registered trademark of Phillips Screw Company. Torx is a registered trademark of Textron, Inc. All other trademarks
are property of their respective companies.
ECopyright 2002–2010 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Eaton Corporation.
Eaton 9170+Rail Kit (9- and 12-Slot Cabinets) Installation Guide S164201420 Rev D Draft 08-Mar-2010 1
Rackmount Installation
To install a 9- or 12-slot uninterruptible power system (UPS) cabinet into
a rack, you must order a cabinet specifically designed for rackmounting.
Nine- and 12-slot battery cabinets are also available for rackmounting.
These models can be installed in an EIA-standard 48.3 cm (19”)
equipment rack and include a rackmounting kit with the brackets and
required hardware.
Checking the Rail Kit Accessories
Verify that the following items are included inside each rail kit:
S(2) front rails (left and right)
S(2) rear rails (left and right)
S(12) #6-32 0.75”screws
S(12) #6 flat-head washers
S(12) #6-32 Keps nuts
S(4) adapter plates
S(8) #10-32 0.5”pan-head screws
S(8) #10 washers
S9-Slot Cabinets:
- (12) metal clip nuts
- (4) rackmount ears
- (12) 1/4-20 1/2”Phillips-head bolts
S12-Slot Cabinets:
- (18) metal clip nuts
- (6) rackmount ears
- (18) 1/4-20 1/2”Phillips-head bolts
Tools Required
To assemble the components, the following tools may be needed:
SMedium flat-bladed screwdriver
SPhillips®#2 screwdriver
RACKMOUNT INSTALLATION
Eaton 9170+Rail Kit (9- and 12-Slot Cabinets) Installation Guide S164201420 Rev D Draft 08-Mar-2010
2
Installing the Rail Kit
CAUTION
The 9- and 12-slot cabinets are heavy [9-slot: 72 kg (158 lb); 12-slot: 89 kg (196 lb)]. This
procedure requires two people to lift and position the cabinet into the equipment rack.
Install the cabinet in the rack before installing power and battery modules and before
making connections to the intended power source.
To install the UPS or battery cabinet in the equipment rack:
1. Measure the distance from the front to back of the mounting posts
in your rack.
2. Position the front and rear rails for the depth of your rack.
3. Loosely assemble the left and right rails using six #6-32 0.75”
screws, #6 flat-head washers, and #6-32 Keps nuts (see Figure 1).
Set aside the loosely assembled rails.
Figure 1. Assembling the Rails
RACKMOUNT INSTALLATION
Eaton 9170+Rail Kit (9- and 12-Slot Cabinets) Installation Guide S164201420 Rev D Draft 08-Mar-2010 3
4. Install six metal clip nuts (nine clip nuts for 12-slot cabinets) onto
each side flange along the front of the cabinet (see Figure 2).
NOTE DO NOT install metal clip nuts in the bottom cabinet section.
Tab Slots
Metal Clip Nuts
Tab Slots
Tab Slots
Metal Clip Nuts
Metal Clip Nuts
Figure 2. Metal Clip Nut and Tab Slot Locations
RACKMOUNT INSTALLATION
Eaton 9170+Rail Kit (9- and 12-Slot Cabinets) Installation Guide S164201420 Rev D Draft 08-Mar-2010
4
5. Install two rackmount ears (three for 12-slot cabinets) on each side
of the cabinet (see Figure 3).
Insert the two offset tabs on the rear edge of the ear into the
matching tab slots on the cabinet side frame (see Figure 2). Pivot
the ear forward until it is flush against the cabinet side frame.
Secure each ear with three 1/4-20 1/2”Phillips-head bolts; screw
the bolts into the metal clip nuts installed in Step 4.
NOTE DO NOT install rackmount ears in the bottom cabinet section.
Rackmount Ear
Rackmount Ear
Rackmount Ear
Figure 3. Rackmount Ears Installed
RACKMOUNT INSTALLATION
Eaton 9170+Rail Kit (9- and 12-Slot Cabinets) Installation Guide S164201420 Rev D Draft 08-Mar-2010 5
6. Select the proper holes in the rail that position the cabinet at the
desired location in the rack.
7. Secure the loosely assembled rail to the front and rear of the rack
with the supplied adapter plate in front of the mounting post using
two supplied #10-32 0.5”pan-head screws and #10 washers.
Repeat for the other side of the rack.
NOTE Figure 4 shows the mounting installation for a rack with the rail return on the
outside. If the rail return is on the inside, the adapter plate must go behind the mounting
post.
8. Tighten the rail assembly screws.
Pan-Head Screws and
#10 Washers
Adapter Plate
Adapter Plate
Pan-Head Screws and
#10 Washers
Rail Return
Mounting Post
Figure 4. Securing the Rails
RACKMOUNT INSTALLATION
Eaton 9170+Rail Kit (9- and 12-Slot Cabinets) Installation Guide S164201420 Rev D Draft 08-Mar-2010
6
9. With one person lifting each side of the cabinet, position the cabinet
onto the two equipment rails (see Figure 5).
Carefully slide the cabinet into the equipment rack until the
rackmount ears of the cabinet are flush with the front vertical rails
of the rack. Verify that the holes in the ears align with the holes in
the rack.
Equipment Rail
Figure 5. Rails Holding UPS Cabinet
10. Secure the cabinet in the rack using #10-32 1/2”Torx®screws or
other appropriate customer-specified screws.
11. Follow the instructions in the UPS user's guide to install the power
and battery modules.
RACKMOUNT INSTALLATION
Eaton 9170+Rail Kit (9- and 12-Slot Cabinets) Installation Guide S164201420 Rev D Draft 08-Mar-2010 7
Service and Support
If you have any questions or problems with the UPS, call your Local
Distributor or the Help Desk at one of the following telephone numbers
and ask for a UPS technical representative.
United States: 1-800-356-5737
Canada: 1-800-461-9166 ext 260
All other countries: Call your local service representative
Please have the following information ready when you call the Help
Desk:
SModel number
SSerial number
SVersion number (if available)
SDate of failure or problem
SSymptoms of failure or problem
SCustomer return address and contact information
If repair is required, you will be given a Returned Material Authorization
(RMA) Number. This number must appear on the outside of the package
and on the Bill Of Lading (if applicable). Use the original packaging or
request packaging from the Help Desk or distributor. Units damaged in
shipment as a result of improper packaging are not covered under
warranty. A replacement or repair unit will be shipped, freight prepaid for
all warrantied units.
NOTE For critical applications, immediate replacement may be available. Call the Help
Desk for the dealer or distributor nearest you.
RACKMOUNT INSTALLATION
Eaton 9170+Rail Kit (9- and 12-Slot Cabinets) Installation Guide S164201420 Rev D Draft 08-Mar-2010
8
Altri manuali per Powerware 9170+
3
Indice
Altri manuali Eaton UPS
Eaton
Eaton Ellipse MAX 600 Manuale utente
Eaton
Eaton 9315 Manuale utente
Eaton
Eaton BladeUPS none Manuale utente
Eaton
Eaton ModularEasy 9PXMEZ6Ki Manuale utente
Eaton
Eaton FerrUPS FE Manuale utente
Eaton
Eaton 9E1000i Manuale utente
Eaton
Eaton 93E MK2 Manuale utente
Eaton
Eaton Powerware 9355 Manuale utente
Eaton
Eaton 9SX Series Manuale utente
Eaton
Eaton 9155 UPS Manuale utente
Eaton
Eaton 5E650i Manuale utente
Eaton
Eaton Powerware 9130 Manuale utente
Eaton
Eaton DIN24240DC Istruzioni per il montaggio
Eaton
Eaton Ellipse ECO 500 Manuale utente
Eaton
Eaton 5E Istruzioni per il montaggio
Eaton
Eaton 93E Manuale utente
Eaton
Eaton 5E Istruzioni per il montaggio
Eaton
Eaton DX-EMC34 Series Manuale
Eaton
Eaton E Series DX Manuale utente
Eaton
Eaton 93PM IBC-L Manuale utente
Manuali UPS popolari di altre marche
Pylontech
Pylontech Victron & Pylontech US5000 Manuale utente
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Manuale utente
Mecer
Mecer ME-1000-WTU Manuale utente
Mustek
Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento
Emerson
Emerson Liebert NXL series Manuale utente
MAKELSAN
MAKELSAN BOXER SERIES Manuale utente
