EcoDim Eco-Dim.10 Zigbee Manuale utente
USER MANUAL
Smart LED dimmer Zigbee 250W
Eco-Dim.10 Zigbee
Trailing Edge
Please Read this manual Carefully before installation.
Important!
• It is dangerous if people without proper training work on an electrical
installation!
• There may be a dangerous voltage at the output of the dimmer!
• When working on the wiring always switch off the mains voltage. Failure to
observe this warning may result in death or seriour injury!
• Read the instructions carefully. Incorrect installtion may damage the
dimmer beyond repair.
• Het is gevaarlijk als mensen zonder goede training aan een elektrische
installatie werken!
• Er is mogelijk een gevaarlijke spanning aan de uitgang van de dimmer!
• Schakel bij werkzaamheden aan de bedrading altijd de netspanning uit. Het
niet in acht nemen van deze waarschuwing kan de dood of ernstig letsel tot
gevolg hebben!
• Lees de instructies aandachtig door. Onjuiste installatie kan de dimmer
onherstelbaar beschadigen.
• Es ist gefährlich, wenn Personen ohne entsprechende Ausbildung an einer
elektrischen Anlage arbeiten!
• Am Ausgang des Dimmers liegt möglicherweise eine gefährliche Spannung
an!
• Schalten Sie bei Arbeiten an der Verkabelung immer die Netzspannung
aus. Die Nichtbeachtung dieser Warnung kann zu schweren oder tödlichen
Verletzungen führen!
• Lesen Sie die Anweisungen sorgfältig durch. Eine falsche Installation kann
den Dimmer irreparabel beschädigen.
Lees deze handleiding zorgvuldig door voordat u met de installatie
begint.
Belangrijk!
Bitte lesen Sie dieses Handbuch vor der Installation sorgfältig durch.
Wichtig!
ENGLISH Manual..........................................................
Nederlandse Handleiding............................................
Deutsches Handbuch...................................................
INDEX(Zigbee Info & Commands)...............................
1
8
15
22
Trailing Edge
Smart Dimmer Module 250W LED
Item NO. Eco-Dim.10 Zigbee
Min. Setting
To set the minimum light level.
Max. Setting
To set the maximum light level.
√ Zigbee support
√ Suitable for several home automation apps
√ Voice support (Amazon Alexa & Google Assistant / Homey)
√ Works with push-button (momentary switch)
√ Optimal dimmable & light stability
√ Suitable for 250W LED
√ Saves and restores the last status after a power failure
√ MIN and MAX light adjustment and dimming speed
√ Suitable for 90% of all LEDs
√ Does not require a neutral wire, 3 wired connection available
√ Soft start system
√ Noiseless dimming
LED Indicator
Indicates resets and when the dimmer is
in pairing mode
Reset Button
To set the dimmer to factory setting or to
pair mode.
Dimming Speed. Setting
To set dimming speed.
1
230 Vac, 50Hz
Input voltage
Power (load)
Suitable for
Type dimmer
Working temperature
Operation
Dimensions
Weight
250W LED
Led-, halogen-, incandescent bulbs
R,C Phase cut
40 °C
Push Dimming by Momentary Switch
45.1*45.1*19.8mm
35.4g
250W Halogen light bulbs
1. Specifications
2
1). Turn off the power
To prevent electrical shock and/or equipment damage, disconnect
electrical power at the main fuse or circuit breaker before installation and
maintenance. Be aware that even if the circuit breaker is off, some voltage
may remain in the wires — before proceeding with the installation, be
sure no voltage is present in the wiring. Take extra precautions to avoid
accidentally turning the device on during installation.
2). Connect the device exactly according to the diagrams shown below
The dimmer is available for 2 and 3 wired connection. Please note in case
of a 2 wired connection port 3 and Load must be connected to make
stable dimming possible.
N
L
N
L
Not suitable for 2way switch, must
be push/ Momentary switch
3). Turn the power back
3. Min./Max./Dimming Speed adjustment
2. Installation
For the SMART dimmer to work optimally or suitable for your preference,
you can adjust the brightness at the Min. and Max. level and also the
dimming speed with the MIN./MAX./Dimming Speed adjustment.
3
Trailing Edge Trailing Edge
Trailing Edge
MIN adjustment: Switch on the lights, insert a screwdriver in MIN and
turn to the left. When the light becomes unsteady, turn slightly back to
the right so that the light remains steady.
MAX adjustment: Switch on the lights, insert a screwdriver in MAX and
turn to the right. When the light becomes unsteady, turn slightly back to
the left so that the light remains steady.
Dimming Speed adjustment: Insert a screwdriver in Speed, clockwise to
increase the dimming speed when you push the momentary switch, vice
versa.
4. Zigbee Setting
1). Factory Reset
Step 1. Press the
reset button for
5s.
Step 2. When the led
indicator stays red for
10S the reset is
finished.
Please Note:
This procedure should only be used when the primary controller is
inoperable.
All configuration will be reset after the device is reset or removed from the
network.
4
Trailing Edge
Trailing Edge
2). Inclusion to a Zigbee Network
Step 2. Double
Press the reset
button.
Step 3. The indicator
will start blinking blue
and stay solid for 10S
when pairing
succeded. Timeout
15mins.
Step 1. Remove the device from the previous Zigbee network in case it
has been added to, otherwise pairing mode will fail.
Step 1. Press the
reset button for 3
times.
Step 2. The indicator
will start blinking
purple and stay solid
for 10s when the
removal is done. Time
out 3 mins.
3). Remove from a Zigbee Network
Method 1. Choose delete or reset as instructed from your Z-Wave hub
interface
Method 2. Remove from the Device, see below instructions.
5
Trailing Edge
Trailing Edge
6
Step 1. Press the
reset button for 4
times.
Step 2. The indicator
will start blinking green
and stay solid for 10s
when pairing is
succeded. Time out
15mins.
4) TouchLink
Step 3. Bring the
remote within 10cm of
the smart dimmer and
set the remote into
TouchLink
commissioning.
Step 4. The light will
blink 10 times when
Touchlink succeded.
Note:
a. When both devices (dimmer and remote) are not included in a Zigbee Network, each
dimmer can link with max. one remote.
b. When both devices are included in the same Zigbee network, each dimmer can link with
max 30 remotes.
c. For Philips Hue Hubs and Amazon Echo Plus, add remote and device to network first then
touchlink.
Step 1. Press the reset
button for 5 times.
Step 2. The indicator
will start blinking
yellow and stay solid
for 10s.
5) Find and Bind
Step 3. Set the remote
into find and bind mode
and enable it to find and
bind commisioning.
Please refer to the
manual for instructions.
Note: Make sure the device and remote already added to the same Zigbee network
Step 4. There shall be
an indication on the
remote that it binds
the device successfully
and can control it.
Trailing Edge
Smart Dimmer Module 250W LED
Item nr. Eco-Dim.10 Zigbee
MIN afstelling
Hiermee kunt u het minimale lichtniveau
instellen.
MAX afstellen
Hiermee kunt u het maximale lichtniveau
instellen.
√ Zigbee-ondersteuning
√ Geschikt voor meerdere apps voor huisautomatisering
√ Spraakondersteuning (Amazon Alexa & Google Assistant / Homey)
√ Werkt met drukknop (pulsschakelaar)
√ Optimale dimbaarheid en lichtstabiliteit
√ Geschikt voor 250W LED
√ Slaat de oude status op en herstelt deze na een stroomstoring
√ MIN en MAX lichtinstellingen en dimsnelheid.
√ Geschikt voor 90% van alle LED's
√ Vereist geen nuldraad, 3-draads aansluiting beschikbaar
√ Soft start-systeem
√ Geruisloos dimmen
LED lampje/indicator
Het led lampje zal in een bepaalde kleur
beginnen te knipperen wanneer deze in
reset- of koppelstand staat.
Resetknop
Hiermee kunt u de dimmer naar
fabrieksinstellingen of in pairingmodus
zetten.
Instelling dimsnelheid
Hiermee kunt u de dimsnelheid instellen.
7
Indice
Lingue:
Altri manuali EcoDim Dimmer
EcoDim
EcoDim Eco-Dim.07 Z-Wave Manuale utente
EcoDim
EcoDim ECO-DIM.07 Zigbee PRO Manuale utente
EcoDim
EcoDim ECO-DIM.04 Manuale utente
EcoDim
EcoDim ECO-DIM.08 Manuale utente
EcoDim
EcoDim ECO-DIM.07 Zigbee Manuale utente
EcoDim
EcoDim ECO-DIM.05 Zigbee Manuale utente
EcoDim
EcoDim ECO-DIM.13 Zigbee Manuale utente
EcoDim
EcoDim ECO-DIM.07 WiFi Manuale utente
