ECRM KnockOut 4550 Manuale

IMAGESETTERS THAT MAKE REAL SENSE

554 Clark Rd.

Tewksbury, MA 01876

Phone (508) 851-0207 Fax - (508) 851-7016

AG11693 - Rev. 8

Document No.

Consisting of:

AG11693 Rev 8 Cover Sheets

AG11718 Rev 6 Operator Guide Text

AO11693 Rev 6

KnockOut 4550®

Operator Guide

KnockOut 4550®

Operator Guide

This guide reﬂects the KnockOut 4550 as of August, 1997.

Information on ordering additional copies of this manual may be obtained by writing or

calling:

ECRM

Order Processing

554 Clark Road

Tewksbury, MA 01876

Phone No. (

) - (508) 851-0207 — Fax (

) - (508)-851-7016

Phone No. (

) - (44) 1923-218255 — Fax (

) (44) 1923-218256

Phone No. (

Hong Kong

) - 852-2-564-8989 — Fax (

Hong Kong

) 852-2-564-8821

AppleLink

ECRM.SUPPORT (

)

ECRM.UK (

)

FEP.ECRM (

Hong Kong

)

Proprietary Notice

The information contained within this guide is the property of ECRM Incorporated. No transmis-

sion, reproduction, transcription, storage in a retrieval system, translation into any language, or

other use is permitted in whole or in part in any form without ﬁrst obtaining written permission of

ECRM Incorporated.

List of Trademarks or Registrations, ECRM

is a registered trademark of ECRM Incorporated, PelBox

is a registered trademark of

ECRM Incorporated, KnockOut 4550



is a registered trademark of ECRM Incorporated.

AG11693 Rev. 8

Table of Contents

AG11718 Rev 6 i

INTRODUCTION 1-1

PRODUCT COMPLIANCE 2-1

PRODUCT COMPLIANCE DEFINITIONS 2-1

CSA - Canadian Standards Association 2-1

DOC - Department of Communications 2-1

IEC - International Electrotechnical Commission 2-1

FCC - Federal Communications Commission 2-1

LASER 2-1

LASER Product 2-1

LASER Radiation (Light) 2-2

LASER System 2-2

Operation and Maintenance 2-2

Service 2-2

TÜV 2-2

VDE 2-2

LASER SAFETY 2-3

LASER Product Classification 2-3

DESCRIPTION OF LABELS 2-5

Identification and Certification Label (Ratings Plate) 2-5

LASER Warning Labels (Non-interlocked covers) 2-6

LASER Warning Labels (Interlocked Covers). 2-7

PRODUCT SAFETY 2-9

CSA 2-9

TÜV 2-9

ELECTROMAGNETIC EMISSIONS 2-10

FCC - USA 2-10

DOC - CANADA 2-11

EMC Directive - EUROPE 2-11

CONTROL PANEL 3-1

INTRODUCTION 3-1

MENU KEYS 3-2

USING SYSTEM MENUS 3-3

OPERATION AND MAINTENANCE 4-1

INTRODUCTION 4-1

ii AG11718 Rev 6

Table of Contents

SETTING UP THE SYSTEM 4-2

System Setup 4-2

User Setup 4-9

4-10

LOADING MEDIA INTO A 400 FOOT INPUT CASSETTE 4-14

LOADING MEDIA INTO A 200 FOOT INPUT CASSETTE 4-18

ADJUSTING THE INPUT CASSETTE SHELF 4-22

INSTALLING MEDIA INTO THE SYSTEM 4-23

TRANSPORT MODE 4-27

CLEARING MEDIA JAMS 4-29

Buffer Media Jams 4-29

Output Slot Media Jam 4-30

STATUS MESSAGES 4-31

TRANSPORT STATUS DISPLAY 4-36

ERROR MESSAGES 4-40

ROLLER CLEANING PROCEDURE 4-41

AIR FILTER CLEANING PROCEDURE 4-44

EMPTYING THE PUNCH TRAY 4-45

CLEANING THE SYSTEM 4-45

APPENDIX A A-1

DIAGNOSTIC MENU A-1

Introduction

AG11718 Rev 6 1-1

Introduction

This book provides the information you will need to operate

your imagesetter. Some of the topics covered are: Laser Regu-

lations, The Control Panel, Operating Menus, Loading Film

Into the Cassette, Loading the Cassette into the System, and

Status and Error Messages.

Section 2 contains important safety information about the laser

and the covers and interlocks that the system contains to pre-

vent accidental exposure to the laser beam. Please read this

information carefully.

ATTENTION!

This symbol is used throughout the Operator Guide

to alert you to cautions, warnings and other

important notes.

WARNING

LIVE CIRCUITS BEFORE MAINS SWITCH!

AC power is connected to theVoltage Selector

Switch, Line Filter, AC Fan Fuse, AC Fan, and Mains

Switch.This circuit does NOT shut off when the

mains switch is turned off.To remove power from this

circuit, unplug the AC Line Cord from the rear of the

system.

1-2 AG11718 Rev 6

Introduction

IMPORTANT!

System fan is ALWAYS ON!

Prior to connecting the imagesetter to the AC mains sup-

ply voltage, ensure the AC Fan Line Voltage Selector

Switch (located on the bottom of the rear panel) is set for

proper mains supply voltage.

WARNING!

If the AC Fan LineVoltage Selector Switch is set incorrectly

when the imagesetter is plugged in, damage may occur to

the imagesetter.

AC Fan LineVoltage

Selector Switch

SCSI Interface

Connector PelBox Interface

Connector

On Line Processor

Connector

Introduction

AG11718 Rev 6 1-3

IMPORTANT NOTE!

If mains supply voltage is removed from the imagesetter

(turning off the fan) while the imagesetter is connected to

online ﬁlm processor, remove the cover on the ﬁlm pro-

cessor.This will prevent the ﬁlm processor fumes from

getting into the imagesetter.

1-4 AG11718 Rev 6

Introduction

Indice

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente