edding in-line 12 Manuale utente
www.edding.tech
User manual
edding in-line
Page 2
Table of contents
1 Technical data ........................................................................................................ 3
1.1 Description ...................................................................................................................... 3
1.2 Assembly notes .............................................................................................................. 4
2 Introduction ............................................................................................................ 6
2.1 Device overview .............................................................................................................. 6
2.2 External keyboard ........................................................................................................... 8
2.3 Start-Wizard .................................................................................................................... 9
2.4 Main screen .................................................................................................................. 10
2.5 Key combinations & Hotkeys ........................................................................................ 14
3 Selection and creation of texts ........................................................................... 15
3.1 Overview of all saved texts ........................................................................................... 15
3.2 Creating a new print message ...................................................................................... 17
4 Settings ................................................................................................................. 19
4.1 Assistants & Setup Instructions .................................................................................... 19
4.2 General ......................................................................................................................... 20
4.3 Print .............................................................................................................................. 24
4.4 External equipment ....................................................................................................... 26
5 Speed charts ......................................................................................................... 27
5.1 Print speed and settings ............................................................................................... 27
5.2 Message frequency ...................................................................................................... 28
6 External communication ..................................................................................... 29
6.1 Access from PC or smartphone/tablet .......................................................................... 29
6.2 External +24V-signals ................................................................................................... 32
6.3 UV-Lamp ....................................................................................................................... 34
6.4 http-Requests ............................................................................................................... 36
6.5 Dynamic fields via TCP/IP port ..................................................................................... 37
7 Troubleshooting ................................................................................................... 38
8 Printer Control Center ......................................................................................... 39
Page 3
Congratulations on the buying of a user-friendly, environmentally friendly and high quality “made
in Germany” product.
Now you own a powerful device allowing you to increase your production efficiency, eliminate
coding errors and ultimately enter the industry 4.0 era.
And even better: With an edding-printer, you are eligible for firmware upgrades that will improve
your system every single day.
1 Technical data
1.1 Description
Print process
High-res Thermal Inkjet (TIJ) printing technology with 600 dpi
Printing distance to surface up to 8 mm
Print height
In-line 12: Up to 11 lines, between 1.0 mm and 12.7 mm (0.5 inch)
In-line 25: Up to 22 lines, between 1.0 mm and 25,4 mm (1 inch)
Print speed
120 m per minute with horizontal resolution of 150 dpi
Greater speed at lower resolution
Print surfaces
Wide range of inks for almost all materials and surfaces in several colours
Print options
Alphanumeric characters and logos, date/time, counter,
batch/box number, 1D and 2D barcodes
Memory capacity
Internal memory (8GB) for more than 1,000,000 messages.
Network connectivity
Communication interfaces MQTT, OPC UA, http request and TCP-Server
Web server for access from every workstation
User interface
Intuitive user interface with real WYSIWYG print preview
Automatic wizards for printer set-up
Step-by-step graphic tutorials for set-up and maintenance on the printer
display
Input devices
Wireless compact keyboard (included)
Any tablet, smartphone or PC
Display
Capacitive colour LCD touchscreen with 4.3 inch display and LED
technology
Indicator lights
6 LED lights (On/Off, printing, low ink, alarm, right/left print direction)
Input / Output
RJ 45 Ethernet connection including DHCP
Dedicated industrial port for rotary encoder, alarm and two, relay / and
light scanner photocell ports (PC 1 & 2)
Light scanner PC 2 input can be used as multi-IO: Reset product counter,
increase product counter, change print direction, start/stop printing, etc.
2 high-speed USB 2.0 input ports
Language selection
German, English, French, Polish, Portuguese, Romanian, Russian,
Spanish, Turkish, Korean, Chinese, Danish
Housing / Body
Ultra-robust and impact-resistant aluminium housing
Stainless steel deflector on the front of the printer for food environments
4-in-1 sandwich design (controller, screen, push-button and ink cartridge)
Independent unit, can be used without PC
Accessories
Mounting Structure (Length: xx, Diameter: xxx), USB Keyboard …
Power supply
Power adapter: AC 100–240 V, 50/60 Hz, 1.6 A, automatic switching
Printer: 24 V, 2.5 A
Page 4
Dimensions (L/W/H)
123.5 x 77.2 x 83.0 m
Weight
0.6 kg – without ink cartridge and mount
Operating environment
5–40 °C (41–104 °F) at 10–90 % humidity (non-condensing)
Quality
Made in Germany
Following ISO 9001, CIG 023, IEC 62368 (US)
1.2 Assembly notes
- To assemble the system, please read the “step-by-step section” above the graphical
representation or the graphic step-by-step tutorial stored on the printer (settings,
mounting instructions).
Ensure that all screws are tight and the device is protected against shocks and impact.
External damage such as bumps/knocks is not covered by the warranty.
Grounding of the housing is optional. It is recommended in case of static charging!
Page 5
Step-by-Step introduction:
1. Screw attachment piece to printer using two of the supplied screws
2. Mark base piece at the mounting position using the supplied drill hole marker
3. Attach base piece using the supplied screws and nuts, and screw first mounting rod
to the base
4. Attach second rod using the first cross clamp
5. Depending on mounting position, attach third rod as required using the second
cross clamp
6. Screw printer to the mount. To ensure optimum print quality, position the printer so
that you keep a print distance of max. 6 - 8 mm to the print object.
7. Insert cartridges at an angle (approx. 15°) and lock with the fixing lever. If excessive
dust and ink accumulate on the print head (causing deterioration of the print image),
clean the nozzle surface with the cleaning cloth supplied with the cartridge.
8. Commission printer according to the following section
9. Printer is ready!
Some menu items/options contain an additional description on the printer itself. Just click on the
icon and a message with additional information/description will appear.
In the event of functional printer errors that cannot be corrected autonomously, please contact
your on-site/local distribution partner.
Page 6
2 Introduction
This chapter describes the printer, the input and the menu structure.
2.1 Device overview
Status LEDs
Power: Printer is supplied with voltage and powered-up
Print: Printer is in print mode; printing is performed when triggered
Ink low: Remaining cartridge volume is <10%; cartridge should be replaced soon
Alarm: Warning/error; the printer is not currently ready to print
Printing direction: Current print direction, viewed from the rear of the printer
Touchscreen
Central control panel of the printer; can be operated by touch or using the wireless keyboard
supplied.
Accessory ports
PC1/PC2: Printing triggered by an external photocell, for improved
recognition of complex surfaces
Encoder (ENC): Connection of an external rotary pulse encoder for accurately measuring the
current conveyor speed. For an optimal print image, even at varying speeds
Alarm (ALR): Connection of an external alarm light to visualise the operating status
Accessory cable length may not exceed 2.5 metres.
Accessory ports
Ethernet
USB
Power supply
Status LEDs
Touchscreen
Internal photocell
Connection for
grounding cable
Page 7
Ethernet
Gigabit Ethernet port for integrating the printer into an existing network. As a default, the printer
will have the IP address 192.168.0.200.
USB
2x high-speed USB ports for external accessories such as keyboards or USB data carriers.
Power supply
Connection socket for the external mains adapter (C14 DC connector, Ø 5.5 / 2.1 mm). Only
use original mains adapter with 24 V and 2.5 A.
Connection for grounding cable
Connection for discharging static charges and electric currents. A grounding cable is not
required (optional only).
Attention: For applications with high static charge an earthing should be connected.
Page 8
2.2 External keyboard
A wireless keyboard is part of the printer's scope of delivery and is required above all for
entering new texts. It communicates wirelessly with the printer by plugging the small USB
receiver (2.4 GHz Wireless Technology) into the left USB port on the back of the printer.
Requires 2x AAA batteries (included).
Keyboard, USB receiver und 2x AAA batteries.
The USB receiver is located in the battery compartment
on the back. Open the lid, remove the USB receiver
from the compartment, insert the AAA batteries in the
compartment provided and close the lid again.
Plug the USB receiver into the left USB port of the printer
(marked green).
To turn the keyboard on and off, slide the Off/On switch
on the back of the keyboard in the "On" direction
(marked blue).
Any other USB keyboard can also be used.
X
OFF ON
Page 9
2.3 Start-Wizard
When the printer is first powered-up, use the “Basic Settings” assistant (under “Preferences”)
for setting up the printer:
Selection of the language for operating the printer. Selection
is made using the red left or right arrows. Confirm with “Next”.
Selection of the current date and time.
Selection of the print direction is defined from the rear of the
printer. “From right” means the products move from right to
left on the printer.
To use an external rotary encoder, confirm selection
accordingly with “ON”.
Selection “ON”: The parameters of the external encoder are
prompted.
Selection “OFF“: Asks for the speed of the passing products.
Selection of whether the accessory “external photocell” is
connected to the printer. Otherwise triggered by the
integrated internal photocell.
Page 10
2.4 Main screen
Central control panel for all important print functions:
General print status: green when the printer is ready to print and red when
there is an error and printing is suspended. Clicking on this button will
show further details on the ink and the device.
Number of actual prints performed.
Indication of the current printer mode.
Type of ink cartridge currently used. Colour of the dot indicates the colour
of the ink.
Remaining volume of current cartridge in %. From <10% the warning “low
ink” is displayed on the status LED.
Actual date (dd/mm/yy) and time (hh:mm).
The printer can be shut down by pressing the button. Then disconnect the
main plug.
Press field to open the menu to create new text, edit existing text, and
select the text to be printed.
Press field to open the printer settings menu. This also includes step-by-
step graphic tutorials and settings wizards.
Printer and
Cartridge status
Print preview
Control area
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali edding Stampante
