Edge-Core ECS4510-12PD Manuale utente
– 1 –
Quick Start Guide
L2 Gigabit Ethernet Switch
ECS4510-12PD
The ECS4510-12PD is a high-performance enterprise Layer 2 switch that provides
ten 10/100BASE-T RJ-45 ports and two Gigabit Small Form Factor Pluggable (SFP)
slots that support 1000BASE-SX and 1000BASE-LX transceivers. RJ-45 ports 1 to 8
on the switch are 802.3at PoE PD ports, and RJ-45 port 10 is an 802.3af PoE PSE port.
Note:
For detailed switch installation information, refer to the Installation Guide,
which is on the Documentation CD included with the switch.
Note:
For Safety and Regulatory information, refer to the Safety and Regulatory
Information document included with the switch.
Warning For Indoor use only:
The switch and all connected cables are not
designed for outdoor use.
The switch is designed to be installed in a standard 19-inch equipment rack.
However, you can also install the switch on any flat surface, such as a desktop.
Follow the steps in this guide to install the switch in your network.
1. Unpack the Switch Unpack the switch and check the package contents.
◆ECS4510-12PD L2 Gigabit Ethernet Switch
◆Rack Mounting Kit containing two brackets and eight screws for attaching the
brackets to the switch
◆Four adhesive foot pads
◆3 Pin 5.08 mm pitch DC Terminal Block/Power Plug—Dinkle Cat. No. 2ESDV-03P
E042014-AP-R02
150200000759A
www.edge-core.com
Quick Start Guide
– 2 –
◆Console cable (RJ-45 to DB-9)
◆Quick Start Guide (this document)
◆Regulatory and Safety Information
◆Documentation CD — includes Installation Guide and Management Guide
2. Install the Switch The switch can be mounted in a standard 19-inch rack or on a desktop or shelf.
Rack Mounting
—Following your rack plan, mark the holes in the rack where the
switch will be installed. Lift the switch into the rack so that it is aligned with the
marked holes. With the switch brackets aligned in the proper position, secure the
switch in the rack, using four rack-mounting screws (not provided).
Desktop or Shelf Mounting
—Attach the four adhesive feet to the bottom of the
switch, then set the device on a desktop, shelf, or other flat surface.
Attach the brackets to the switch,
then use the rack mounting screws
supplied with the rack to secure the
switch in the rack.
Attach the four adhesive rubber foot
pads to the recessed areas on the
bottom of the switch.
Quick Start Guide
– 3 –
3. Connect Power The ECS4510-12PD can be powered by either:
◆PoE power from a PSE device connected to any of Ethernet ports 1 to 8
◆From an external DC 48 VDC supply using the supplied 3-pin terminal block
plug.
To connect external DC power, connect the terminal block plug to a 48 VDC, 0.65 A
power supply using AWG 20/22 DC wiring as shown in the table and figure below.
4. Verify Switch
Operation
Verify basic switch operation by checking the system LEDs.
When operating normally, the Power and Diag LEDs should be on green.
Plug Pin Number Description
1DC+Positive
2DC-Negative
3Ground
Plug the DC power plug into the
socket on the rear of the switch.
System Status LEDs
Quick Start Guide
– 4 –
5. Make Initial
Configuration
Changes
At this point you may need to make a few basic switch configuration changes
before connecting to the network. It is suggested to connect to the switch console
port to perform this task.
The serial port’s configuration requirements are as follows: 115200 bps, 8
characters, no parity, one stop bit, 8 data bits, and no flow control.
You can log in to the command-line interface (CLI) using default settings: User
name “admin” with password “admin.”
For information on initial switch configuration, refer to the Management Guide,
which is on the Documentation CD included with the switch.
6. Connect Network
Cables
Connect network cables to port interfaces:
◆For the RJ-45 ports, use 100-ohm Category 5, 5e or better cable for 1000BASE-T
connections, or Category 5 or better for 100BASE-TX connections.
◆For the SFP slots, first install SFP transceivers and then connect cabling to the
transceiver ports.
Console Port
Connect Category 5 or better cables
with RJ-45 plugs to the RJ-45 ports.
Quick Start Guide
– 5 –
The SFP slots support the following transceiver types: 1000BASE-SX and 1000BASE-
LX.
As connections are made, check the port status LEDs to be sure the links are valid.
Note:
For further switch configuration information, refer to the Management
Guide,which is on the Documentation CD included with the switch.
For fiber transceivers, connect
62.5/125 or 50/125 multimode
or 9/125 single-mode fiber with
LC connectors.
Quick Start Guide
– 6 –
Hardware Specifications
Item Specification
Chassis Specifications
SIze (W x D x H) 18.00 x 16.50 x 3.75 cm (7.09 x 6.50 x 1.48 in)
Weight 0.665 kg (1.47 lb)
Temperature Operating: 0° C to 50° C (32° F to 122° F)
Storage: -40° C to 70° C (-40° F to 158° F)
Humidity Operating: 10% to 90% (non-condensing)
Power Specifications
DC Input DC 48 V 0.65 A
Maximum Power
Consumption
PoE PSE disabled: 15 W
PoE PSE enabled: 30.4 W
Regulatory Compliances
Emissions EN55022 (CISPR 22) Class A
EN 61000-3-2/3
FCC Class A
CE Mark
Immunity EN 61000-4-2/3/4/5/6/8/11
Safety cTUVus (CSA 22.2 NO 60950-1 & UL 60950-1)
CB (IEC/EN60950-1)
Altri manuali per ECS4510-12PD
2
Indice
Altri manuali Edge-Core Interruttore
Edge-Core
Edge-Core SMCGS26C-Smart Manuale utente
Edge-Core
Edge-Core AS4630-54NPE Manuale utente
Edge-Core
Edge-Core ECS5520 Series Manuale utente
Edge-Core
Edge-Core Gigabit Ethernet Switch Manuale utente
Edge-Core
Edge-Core ES4308-POE Manuale utente
Edge-Core
Edge-Core AS7535-28XBE Manuale utente
Edge-Core
Edge-Core AGR420 Manuale utente
Edge-Core
Edge-Core ES4308-POE Manuale di programmazione
Edge-Core
Edge-Core ES4626F Manuale di programmazione
Edge-Core
Edge-Core ECS4810-12M Layer 2 Manuale di programmazione
Edge-Core
Edge-Core ECS5610-52S Manuale utente
Edge-Core
Edge-Core AS4610-30T Manuale utente
Edge-Core
Edge-Core ECS5510-48S Manuale utente
Edge-Core
Edge-Core ECS4620-28T Manuale utente
Edge-Core
Edge-Core AS5610-52X Manuale utente
Edge-Core
Edge-Core AS7326-56X Manuale utente
Edge-Core
Edge-Core ECS4810-12M Layer 2 Manuale di programmazione
Edge-Core
Edge-Core ECS1100-5P Manuale utente
Edge-Core
Edge-Core AS6701-32X Manuale utente
Edge-Core
Edge-Core ECS4610-24F Manuale di programmazione
