Eink AB1024-EGA Manuale utente
5.65”E Ink Gallery Palette ™
4000 ePaper Display AB1024-
EGA
i
Table of Contents
Firmware Update SOP .............................................................................1
1Hardware Guide .........................................................................1
(1) Hardware Requirements....................................................................... 1
(2) Hardware Installation ........................................................................... 1
2Software Guide...........................................................................3
(1) Software Requirements........................................................................ 3
(2) Firmware Update by Application Software .......................................... 3
ePaper Display Update SOP.....................................................................5
1Introduction ...............................................................................5
(1) Package Contents.................................................................................. 6
2Hardware Guide .........................................................................7
(1) Hardware Requirements....................................................................... 7
(2) Demo Kit Hardware Description........................................................... 8
(3) Hardware Installation ........................................................................... 9
3Software Guide.........................................................................12
(1) Demo Kit Connection.......................................................................... 12
(2) Update Initial Data.............................................................................. 12
(3) Uploading Image................................................................................. 13
4Troubleshooting .......................................................................14
5Contact Information .................................................................14
6Legal Information .....................................................................14
1
Firmware Update SOP
1Hardware Guide
(1) Hardware Requirements
Buy a set of MSP-EXP430G2
You will get following stuffs in the package
MSP-EXP430G2
(2) Hardware Installation
The programmer need the jump line as the picture below
Connect to MSP430 and HULK MCU board
2
Please connect the Dupont line from J3 (VCC pin) of MSP430 LaunchPad to J1's 2nd
pin of HULK
Please connect the Dupont line from J3 (TEST pin) of MSP430 LaunchPad to J1's 8th
pin of HULK
Please connect the Dupont line from J3 (RST pin) of MSP430 LaunchPad to J1's 11th
pin of HULK
Please connect the Dupont line from J6 (GND pin) of MSP430 LaunchPad to J1's 9th
pin of HULK
Please pay attention! It must remove the HULK's adapter board when updating Firmware.
When you update Firmware, please confirm if the D2(power indicator) or D2(power
indicator) and D1(data indicator) of HULK are lighted.
It can update Firmware when indicators are lighted.
If the indicators are not lighted, please confirm the connect again.
Refer to following figure to setup MSP-EXP430G2 and connect it to your PC
Connect to PC
3
2Software Guide
(1) Software Requirements
Refer the guideline in following FET-Pro430 Lite website to download and setup driver
of MSP-EXP430G2
https://www.elprotronic.com/pages/downloads
Refer to following figure to connect MSP-EXP430G2 with your PC and HULK together.
Connect to PC
(2) Firmware Update by Application Software
Press drop-down menu "Microcontroller Type" to select a MCU model MSP430F5502
Please check "Port USB Automatic" to select 4-wires
4
Press "Open code file" button to select a firmware file (.txt)
Press "AUTO PROG" button to update the firmware into MCU
Show the Pass is firmware update ok.
5
ePaper Display Update SOP
1Introduction
HULK - demo kit, with 5.65" E Ink Gallery Palette ™ 4000 e-Paper display(EPD) –AB1024-
EGA, allows E Ink clients to access hardware and software for evaluation. This kit
demonstrates as a turnkey solution for those who are interested in designing with E Ink
displays. Hardware and software design support is available from E Ink directly.
5.65" E Ink Gallery Palette ™ 4000 display panel is suitable for various applications, e.g.
tag application.
The low power consumption of the AB1024-EGA is ideal for applications such as
electronic shelf labels and indicators.
An All-in-one IC is embedded in the EPD, it include source/gate driver, TCON (Timing
controller), PMIC(power management IC) and Temp. sensor. It allows users to rapidly
design systems by using E Ink displays.
The kit allows E Ink clients to experience loading and viewing custom images on 5.65" E
Ink Gallery Palette ™ 4000 EPD. The use of MCU board to drive an E Ink EPD is
demonstrated with the kit.
IAR Integrated Development Environment (IDE) is adopted to write, download, and
debug an application.
6
(1) Package Contents
This demo kit contains the following:
E Ink demo kit: MCU driving board and E Ink display adapter
5.65" E Ink Gallery Palette ™ 4000 EPD
Mini USB cable
Demo Kit Contents
Specification
Item
Specification
TCON
MSP430
TCON Solution
Hardware TCON
E Ink Display Panel
Dimension (W × H × D, unit: mm)
99.5(W) × 125.4(H) × 1.18(D)
Shape
Rectangular
Resolution
600(H) × 448(V)
Controller Board
Input
5Vdc (USB), power on when connected to PC
5.65" E Ink Gallery Palette ™4000 EPD
MCU board and display adapter
Mini USB cable
7
2Hardware Guide
(1) Hardware Requirements
MCU board and display adapter
EPD panel
Mini USB cable
Windows PC
Minimum PC Requirements
CPU
Pentium III 800 MHz or later
RAM
128MB or greater
Required Software
Windows XP
Interface
USB port
8
(2) Demo Kit Hardware Description
The HULK 5.65" E Ink Gallery Palette ™ 4000 demo Kit includes an MCU board and an E
Ink display adapter board. The MCU board and E Ink display adapter board are connected
via a 16 pin header. The mini USB port on the demo kit supplies data and power to the
MCU board and E Ink panel. Using the E Ink PC application, users can send image data to
the board or update settings.
Demo Kit
There are two LEDs on the MCU board, LED 1 and LED 2. LED 1 indicates the board is
powered. LED 2 is used as a multi-purpose function light
MCU Board for Demo Kit
When LED2 is light on, EPD can’t accept any command
Indice
Altri manuali Eink Monitor
