Eink Spectra 3100 Manuale utente
7.3˝ E Ink Spectra ™ 3100
ePaper Display (EB2000-GCA)
Table of Contents
Firmware Update SOP .............................................................................1
1Hardware Guide .........................................................................1
(1) Hardware Requirements....................................................................... 1
(2) Hardware Installation ........................................................................... 1
2Software Guide...........................................................................3
(1) Software Requirements........................................................................ 3
(2) Firmware Update by Application Software .......................................... 4
ePaper Display Update SOP.....................................................................6
1Introduction ...............................................................................6
(1) Package Contents.................................................................................. 7
2Hardware Guide .........................................................................8
(1) Hardware Requirements....................................................................... 8
(2) Demo Kit Hardware Description........................................................... 9
(3) Hardware Installation ......................................................................... 10
3Software Guide.........................................................................13
(1) Demo Kit Connection.......................................................................... 13
(2) Update Initial Data.............................................................................. 13
(3) Uploading Image................................................................................. 14
4Troubleshooting .......................................................................15
5Contact Information .................................................................15
6Legal Information .....................................................................15
1
Firmware Update SOP
1Hardware Guide
(1) Hardware Requirements
Buy a set of MSP-EXP430G2
You will get following stuffs in the package
MSP-EXP430G2
(2) Hardware Installation
The programmer needs the jump line as the picture below
Connect to MSP430 and THOR MCU board
Please connect the Dupont line from J3 (VCC pin) of MSP430 LaunchPad to J1's 2nd
pin of Thor
Please connect the Dupont line from J3 (TEST pin) of MSP430 LaunchPad to J1's 8th
2
pin of Thor
Please connect the Dupont line from J3 (RST pin) of MSP430 LaunchPad to J1's 11th
pin of Thor
Please connect the Dupont line from J6 (GND pin) of MSP430 LaunchPad to J1's 9th
pin of Thor
Please pay attention! It must remove the THOR's adapter board when updating
Firmware.
When you update Firmware, please confirm if the D2(power indicator) or D2(power
indicator) and D1(data indicator) of THOR are lighted.
It can update Firmware when indicators are lighted.
If the indicators are not lighted, please confirm the connection again.
Refer to following figure to setup MSP-EXP430G2 and connect it to your PC
Connect to PC
4
(2) Firmware Update by Application Software
Press drop-down menu "Microcontroller Type" to select a MCU model MSP430F5502
Please check "Port USB Automatic" to select 4-wires
Press "Open code file" button to select a firmware file (.txt)
Press "AUTO PROG" button to update the firmware into MCU
5
Show the Pass is firmware update ok.
6
ePaper Display Update SOP
1Introduction
THOR_Spectra3100 demo Kit, with Spectra 3100 e-Paper display allows E Ink clients to
access hardware and software for evaluation. This kit demonstrates as a turnkey solution
for those who are interested in designing with E Ink displays. Hardware and software
design support is available from E Ink directly.
Spectra 3100 EPD is suitable for various applications, e.g. Electronic shelf labels
The low power consumption of the Spectra 3100 EPD is ideal for applications such as
electronic shelf labels and indicators.
An All-in-one IC is embedded in the EPD, it include source/gate driver, TCON(Timing
controller), PMIC(power management IC) and Temp. sensor. It allows users to rapidly
design systems by using E Ink displays.
The kit allows E Ink clients to experience loading and viewing custom images on Spectra
3100 EPD. The use of MCU board to drive an E Ink EPD is demonstrated with the kit.
IAR Integrated Development Environment (IDE) is adopted to write, download, and
debug an application.
7
(1) Package Contents
This demo kit contains the following:
THOR_Spectra3100 demo Kit: MCU driving board and E Ink display adapter
Spectra 3100 EPD (EPD size is decided by order)
Mini USB cable
Demo Kit Contents
Specification
Item
Specification
MCU
MSP430
TCON Solution
Hardware TCON
E Ink Display Panel
Dimension (W × H × D, unit: mm)
170.2(H)x111.2(V)x0.85(D)
Shape
Square
Resolution
800(H) × 480(V),
Controller Board
Input
5V(USB), power on when connected to PC
8
2Hardware Guide
(1) Hardware Requirements
MCU board and display adapter
EPD panel
Mini USB cable
Windows PC
Minimum PC Requirements
CPU
Pentium III 800 MHz or later
RAM
128MB or greater
Required Software
Windows XP
Interface
USB port
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Eink Monitor
