EIPL 10289MG-GB Manuale utente
24” DRUM FAN
10289MG-GB
USER MANUAL
Drawing No. :- TPC324
Issue :- 1
Date :- 14/01/08
SPECIFICATIONS
Model 24” Drum Fan
Part Number 10289MG-GB
Height 800 mm
Width 720 mm
Depth 410 mm
Weight 22Kg
Voltage 230 Vac
Max Current 0.85 Amps
Max Power 190 Watts
Fuse Rating (UK) 13 amps
SAFETY PRECAUTIONS
•DO NOT operate with safety grilles removed
•DO NOT use in dusty or chemical fume environments
•DO NOT attempt to use a duct or duct air from the unit
•DO NOT use as an extractor fan
•DO NOT use in wet areas / environments e.g. steamy areas like
bathrooms or swimming pools
•DO NOT use if the power cord or outer drum is damaged
•DO NOT cover or obstruct the safety grilles
•DO NOT poke objects into the safety grilles or foul the impellor
•DO NOT use if the impellors are damaged at all
If in doubt then contact Ebac Industrial Products Limited on the details
below. If any item on or within the unit is damaged then only a qualified
technician should service the Drum Fan. Service manuals and spares lists
are available upon request.
CONTACT DETAILS
Telephone: 01388 664400 Ebac Industrial Products Limited
Fax: 01388 662590 St. Helens Trading Estate
Web: www.eipl.co.uk Bishop Auckland
DL14 9AD
INTRODUCTION
Your product is packed in a plastic wrapper – please ensure that it is
disposed of safely and where it will not be a danger to children.
Your 24“ Drum Fan is designed to circulate air indoors. The purpose of
which could be to cool workers on a production line where the air might be
stale, etc. It can also be used in conjunction with large dehumidifiers to
circulate air and therefore help speed up the drying process.
Before using this product the manual should be fully read and the
instructions within this manual should be carefully followed. This is mainly
to keep you the user safe and also to ensure no damage will occur to the
Drum Fan through incorrect operation.
OPERATION
Your 24” Drum Fan simply draws air in one side and disperses at the other
side. It does this by means of a 24” impellor and a motor which drives the
impellor. It has 3 speed settings to give a greater or lesser air flow as
required and a tilt function to help direct the air flow to a specific location.
Simply plug the machine into a 230V 50Hz supply and select the required
speed setting; as the speed setting is selected the fan will start to rotate. It
may take a few seconds to get to full speed, this being the normal
operation.
The tilt function is controlled by the hand wheel located on the side of the
machine, but before adjusting the tilt the unit must be turned off and
disconnected from the mains, Turn the hand wheel anti-clockwise to
release the tension but do not fully remove. Once loose the drum of the unit
will be free to pivot through 90° (the drum can be either vertical, horizontal
with air flow direction upwards or anywhere in between. Once the drum is
in the desired position then the hand wheel must be fully tightened to
prevent movement whilst in operation.
ELECTRICAL CONNECTIONS
This unit is fitted with a standard UK mains 3 pin plug (13amp, 230volt,
50Hz).
If the appliance is fitted with a plug for which your socket is unsuitable, then
it should be cut off and an appropriate plug fitted.
This appliance complies with the suppression requirements of the EEC
direction 82/199/EEC as embodied in BS800:1988.
IMPORTANT:- The wires in this mains lead are coloured in accordance
with the following code:-
Green & Yellow Earth
Blue Neutral
Brown Live
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your own
plug, proceed as follows:
The wire which is coloured Green and Yellow must be connected to the
terminal in the plug which is marked with the letter E or by the Earth
Symbol or coloured Green and Yellow. The wire which is coloured Blue
must be connected to the terminal in the plug which is marked with the
letter N or coloured Blue. The wire which is coloured Brown must be
connected to the terminal which is marked with the letter L or coloured
Brown.
You must dispose of the non rewireable plug once it has been removed
from the flexible cord. It is dangerous to attempt to insert the plug into any
electrical socket elsewhere in the house. If the flexible cord becomes
damaged it must be replaced by an identical cord.
Only 13 Amp fuses that are ASTA approved to BS1362 should be used.
The fuse cover must be refitted after replacement of the fuse. In the event
of the fuse cover being lost or damaged, the plug must not be used until a
replacement is obtained. Replacement fuse covers, which must be
coloured BLACK, are obtainable from electrical retailers.
W
ARNIN
G
–
THI
S
APPLIAN
C
E M
US
T BE EARTHED
Altri manuali EIPL Fan
