EK-Quantum Vector Strix RTX 3080 Backplate Manuale utente

USER GUIDE

EK-Quantum

Vector TUF RTX 3080/3090 Active Backplate

This product is intended for installation by expert users only. Please

consult with a qualiﬁed technician. Improper installation may result

in damage to your equipment. EK assumes no liability whatsoever,

expressed or implied, for the use of this product or its installation. The

following instructions are subject to change without notice. Please, read

the manual carefully before beginning with the installation process. For

updates, you can visit our ofﬁcial website www.ekwb.com.

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning with the

installation process.

Remove your graphics card from the computer for the safest

mounting process to prevent any possible damage to your

GPU or its circuit board (PCB).

EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured with the

rubber O-ring gaskets.

The use of quality market-proven corrosion-inhibiting

coolants is always strongly recommended for any liquid

cooling system.

Do not use pure distilled water as a cooling liquid! For best

results, EK recommends the use of EK-CryoFuel Coolants.

Make sure to bleed air out of your water block thoroughly in

order to reach optimal performance.

EK only guarantees compatibility with included EK-brand

thermal pads. Installation process, cooling performance and

block contacts are tested exclusively with EK-brand thermal

pads. Listed thermal pad thicknesses apply only to thermal

pads included in the package.

EK does not guarantee compatibility with aftermarket

alternatives for thermal interface material.

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

ACTIVE BACKPLATE DIMENSIONS 5

REQUIRED TOOLS 5

TECHNICAL SPECIFICATIONS AND PRODUCT PARTS 6

INSTALLING THE ACTIVE BACKPLATE 7

PREPARING THE GRAPHICS CARD 7

CUTTING AND PLACING THERMAL PADS 9

REMOVING THE TERMINAL METAL PLATE 10

ATTACHING THE ACTIVE BACKPLATE 10

INSTALLING FITTINGS AND TUBING 12

CONNECTING THE D-RGB LED STRIP 12

SUPPORT AND SERVICE 13

SOCIAL MEDIA 13

- 4 -

EK-Loop Multi Allen Key (1 pc)

M2.5x8 AX1 Screw (8 pcs) M2.5x8 AX1 Screw - Nickel (8 pcs)

8 mm

2 mm

120 mm

24 mm

1.5 mm

120 mm

24 mm

BOX CONTENTS

Allen Key 2.5 mm (1 pc)EK-Quantum Vector TUF RTX 3080/3090 Active Backplate

Thermal PAD G 1.5 mm - (120x24mm) (3 pcs)

Thermal Pad G 2.0 mm - (120x24mm) (3 pcs)

Universal Mounting Mechanism – You may not need every

screw from this package. EAN: 103301

- 5 -

ACTIVE BACKPLATE DIMENSIONS

255 mm

133 mm

144.5 mm

151.5 mm

122.5 mm

119.5 mm

33 mm

6.2 mm

8 mm

Phillips Head Screwdriver Scissors

REQUIRED TOOLS

- 6 -

TECHNICAL SPECIFICATIONS AND PRODUCT PARTS

Technical Speciﬁcation:

Dimensions (L x H x W): 255 x 144.5 x 33 mm

D-RGB (Addressable RGB) Cable Length: 500 mm

D-RGB LED Count: 5 (Plexi Version)

D-RGB Connector: Standard 3-Pin (+5V, Data, Blocked, Ground)

Position EAN Description Quantity

1103859 ALU BACKPLATE - NICKEL 1

103860 ALU BACKPLATE - BLACK

2103862 COLDPLATE (Nickel) 1

3103631 AB TERMINAL - PLEXI 1

103630 AB TERMINAL - ACETAL

4103865 TOP PLATE - PLEXI 1

103866 TOP PLATE - ACETAL

5103867

ACETAL STICKOUT

68323 M4 x 28 DIN7984 SCREW 6

79047 M2.5 x 4 AX1 SCREW 3

89023 M4x6 DIN7984 SCREW 14

9100199 D-RGB LED STRIP 1

10 104206 MAIN O-RING 1

11 100663 EK BADGE 1

12 5155 TERMINAL O-RING 15 x 1 mm 4

13 4720 TERMINAL METAL PLATE 1

14 103116 PLUG G1/4 CSQ-BRIDGE 1

- 7 -

INSTALLING THE ACTIVE BACKPLATE

STEP 1

PREPARING THE GRAPHICS CARD

First, complete the installation of your EK-Quantum Vector TUF RTX

3080/3090 water block according to its installation manual. In case

the water block is already installed, remove the ﬁve (5) AX1 screws

and their PVC washers, as shown in the image.

STEP 1

Phillips Head Screwdriver

For this Step, you will need:

- 8 -

Allen Key 2.5 mm

For this Step, you will need:

STEP 2

REMOVING THE ORIGINAL TERMINAL

EK-Quantum Vector TUF RTX 3080/3090 Active Backplate comes

with its own terminal, meaning the original terminal, along with two

(2) 15 x 1 O-rings, on the EK-Quantum Vector TUF RTX 3080/3090

water block has to be removed. Unscrew the three (3) M4 x 20

DIN7984 screws and detach the terminal from the water block. The

procedure of terminal detachment is shown in the image.

Attention!

In case the EK-Quantum Vector TUF RTX 3080/3090

water block is already ﬁlled with coolant, empty the

content of the water block before continuing with this

step. Be careful that the coolant that remained in the

water block does not come in contact with the GPU!

M4 x 20 DIN7984

SCREW

TERMINAL COVER

OR 15 x 1 mm

STEP 2

ORIGINAL

TERMINAL

- 9 -

STEP 3

120 mm

24 mm

1.5 mm

Thermal PAD G 1.5 mm (120 x 24 mm)

120 mm

24 mm

2 mm

Thermal PAD G 2.0 mm (120 x 24 mm)

STEP 3

CUTTING AND PLACING THERMAL PADS

Your Active Backplate comes with thermal pads that have to be cut

into smaller pieces to cover all the VRM components. EK made sure

to provide you with more than an adequate quantity of thermal pads

to complete this Step-s.

Replacement thermal pads:

Thermal PAD G 1.5 mm – (120 x 24 mm) – EAN: 3830046996787

Thermal PAD G 2.0 mm – (120 x 24 mm) – EAN: 3830046996794

EK only guarantees compatibility with included EK-brand

thermal pads. Installation process, cooling performance

and block contacts are tested exclusively with EK-brand

thermal pads. Listed thermal pad thicknesses apply only

to thermal pads included in the package.

EK does not guarantee compatibility with aftermarket

alternatives for thermal interface material.

STEP 4

Once cut to size, thermal pads should be placed on the Active

Backplate, as illustrated below.

RTX™3080/3090

STEP 4

Thermal Pad G 1.5 mm

Thermal Pad G 2 mm

G1.5

G1.5 G1.5 G1.5

G1.5

G2 G2

- 10 -

STEP 5

REMOVING THE TERMINAL METAL PLATE

The Metal plate attached on the Terminal is meant as a precaution,

to secure the two O-rings to prevent them from falling out of their

sockets during transport and handling. Before the installation of

the Active Backplate, this metal plate has to be removed. Unscrew

the three (3) M4 x 28 DIN7984 screws with the provided 2.5 mm

Allen Key shown on the picture. Keep the screws as they will be

needed in the upcoming step, unlike the metal plate which will not

be needed anymore.

STEP 5

M4 x 28 7984DIN SCREW

TERMINAL METAL PLATE

Allen Key 2.5 mm

For this Step, you will need:

STEP 6

ATTACHING THE ACTIVE BACKPLATE

First, make sure the two (2) 15 x 1 O-rings are IN terminal

slots, as shown in the image.

STEP 6

Altri manuali per Vector Strix RTX 3080 Backplate

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali EK-Quantum Hardware per computer

EK-Quantum

EK-Quantum Vector FTW3 RTX 3080 Manuale utente

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector Strix RTX 3080 D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector RX 6800/6900 D-RGB - AMD Radeon... Manuale utente

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector FE RTX 3090 Ti D-RGB + Backplate Manuale utente

EK-Quantum

EK-Quantum Vector RX 6800/6900 D-RGB - AMD Radeon... Manuale utente

EK-Quantum

EK-Quantum Momentum MSI Z590 Carbon D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector2 FTW3 RTX 3080 D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manuale utente

EK-Quantum

EK-Quantum EK-Classic GPU Water Block Strix RTX 3070... Manuale utente

EK-Quantum

EK-Quantum Vector2 Red Devil RX 7900 XTX D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector RX 6700XT Backplate Manuale utente

EK-Quantum

EK-Quantum Reflection DK-O5F Left D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manuale utente

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manuale utente

EK-Quantum

EK-Quantum MSI MPG X670E CARBON EK X D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector2 Arc A750-RGB Manuale utente

EK-Quantum

EK-Quantum Vector2 XC3 RTX 3080 D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector Strix RTX 3070 Backplate Manuale utente

EK-Quantum

EK-Quantum Reflection2 PC-O11D XL D5 PWM D-RGB Manuale utente

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manuale utente

EK-Quantum

EK-Quantum Reflection PC-O11D Mini D5 PWM D-RGB Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente