EK-Quantum Vector2 XC3 RTX 3080 D-RGB Manuale utente

USER GUIDE

GPU WATER BLOCK

EK-Quantum

Vector² XC3 RTX 3080/90 D-RGB

This product is intended for installation by expert users only. Please

consult with a qualiﬁed technician. Improper installation may result

in damage to your equipment. EK assumes no liability whatsoever,

expressed or implied, for the use of this product or its installation. The

following instructions are subject to change without notice. Please,

read the manual carefully before starting the installation process. For

updates, you can visit our ofﬁcial website www.ekwb.com.

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning the installation

process.

Remove your graphics card from the computer for the safest

mounting process to prevent any possible damage to your

GPU or its circuit board (PCB).

The EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber O-ring gaskets.

The use of corrosion inhibiting coolants is always

recommended for liquid cooling systems and mandatory for

nickel-plated water blocks!

Do not use pure distilled water! For best results, EK

recommends the use of EK-CryoFuel coolants!

To reach optimal performance, make sure to thoroughly

bleed the air out of your water block!

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

WATER BLOCK DIMENSIONS 5

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6

NICKEL PLEXI 6

NICKEL ACETAL 7

PREPARING THE GRAPHICS CARD 8

REMOVING THE STOCK COOLER 8

CLEANING THE PCB 9

PREPARING THE WATER BLOCK FOR INSTALLATION 10

CUTTING AND PLACING THERMAL PADS 11

APPLYING THERMAL COMPOUND 12

ATTACHING THE WATER BLOCK 12

PREPARING THE BACKPLATE 14

ATTACHING THE BACKPL ATE 16

INSERTING THE GRAPHICS CARD INTO THE CHASSIS 16

FITTINGS AND TUBING 17

CONNECTING THE D-RGB LED STRIP 18

TESTING THE LOOP 18

WARRANTY 19

SUPPORT AND SERVICE 20

SOCIAL MEDIA 20

- 4 -

Thermal Pad F 1.0 mm (6 pcs)

(3830046996732)

120 mm

16 mm

Thermal Pad F 1.5 mm (1 pc)

(3830046996749)

120 mm

16 mm

Thermal Pad F 2.0 mm (2 pcs)

(3830046996756)

120 mm

16 mm

Thermal Grease (1 pc)

BOX CONTENTS

4 mm

8 mm

10 mm

EK-Loop Multi Allen Key (1 pc)

Allen Key 2 mm (1 pc)

Allen Key 2.5 mm (1 pc)

M2.5x8 AX1 Screw (1 pc)

M3x10 AX1 Screw (1 pc)

EK-Quantum Vector2XC3 RTX

3080/90 D-RGB

M2.5x4 AX1 Screw (8 pcs)

Polyamid Washer M2.5 0.5mm (8 pcs)

Standoff Ø4.5/2.5 (1 pc)

Quantum Plug (2 pcs)

EK-Plug Out Spludger Tool (1 pc)

Standoff M2.5-M3 x 6.6mm (1 pc)

Nut M2.5 (2 pcs)

EAN: 104911

EAN: 104549

Terminal OR - Vector

14x1 mm (2 pcs)

- 5 -

WATER BLOCK DIMENSIONS

121.8 mm

27 mm

123.7 mm

134 mm

25.5 mm

95.7 mm

302 mm

- 6 -

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS

NICKEL PLEXI

- Dimensions: (LxHxW): 302 x 134 x 27mm

- D-RGB LED count: 17

- D-RGB cable length: 50 cm

- D-RGB connector 3-pin 5V digital LED header

Position EAN Description Quantity

1104963 Coldplate (Nickel) 1

2103969 Standout (Acetal) 1

3104582 Top plate (Plexi) 1

4103947 FC Terminal 1

5104580 Backplate (Black e.) 1

6103965 Main O-ring 128 x 2 mm 1

7104106 Terminal OR - 14 x 1 mm 2

89024 Screw M4 x 10 7984DIN 11

98208 Screw M3 x 8 7991DIN 2

10 104187 Screw M2.5 x 8 AX1 8

11 103987 Standoff M3.5-M2.5 x 3 4

12 103988 Standoff M4-M2.5 x 3 4

13 103986 Standoff M3.5-M2.5 x 11.3 6

14 104188 Standoff ﬁ 4.5/2.5 8

15 103942 Terminal badge 1

16 8311 Screw M4 x 20 DIN7984 3

17 104216 Disc magnet 3 x 3 2

18 103964 Mylar sticker 2

19 100663 EK RGB Badge 2

20 104570 LED Cover 1

21 101556 LED D-RGB strip 500/300 mm 1

22 103975 Bridge plate 1

23 103962 Plexi insert 1

- 7 -

NICKEL ACETAL

- Dimensions: (LxHxW): 302 x 134 x 27 mm

- D-RGB LED count: 28

- D-RGB cable length: 50 cm

- D-RGB connector 3-pin 5V digital LED header

Position EAN Description Quantity

1104963 Coldplate (Nickel) 1

2103947 FC Terminal (Acetal) 1

3104580 Backplate (Black e.) 1

4103965 Main O-ring 128 x 2 mm 1

5104106 Terminal OR - 14 x 1 mm 2

69024 Screw M4 x 10 DIN7984 11

78202 Screw M3 x 12 DIN7991 2

8104187 Screw M2.5 x 8 AX1 8

9103987 Standoff M3.5-M2.5 x 3 4

10 103988 Standoff M4-M2,5 x 3 4

11 103986 Standoff M3.5-M2.5 x 11.3 6

12 104188 Standoff ﬁ 4.5/2.5 8

13 103966 Light guide 1

14 103972 Standout (Acetal) 1

15 104583 Top plate (Acetal) 1

16 103942 Terminal badge 1

17 8311 Screw M4 x 20 DIN7984 3

18 104216 Disc magnet 3 x 3 2

19 104211 Mylar sticker 2

20 100663 EK - Badge 2

21 104295 LED D-RGB Dense Strip Double 1

22 103975 Bridge Plate 1

23 103962 Plexi insert 1

- 8 -

PREPARING THE GRAPHICS CARD

STEP 1

REMOVING THE STOCK COOLER

OPTION 1 – GPU Versions Without a Backplate

Some versions of this GPU don’t have a backplate (e.g., EVGA GeForce

RTX 3080 XC3 BLACK GAMING).

Use the Phillips head screwdriver to remove the eleven marked screws

and the Stock Cooler Backplate from the backside of the GPU. You do

not have to remove the unmarked I/O Bracket screw.

Carefully detach the PCB from the stock cooler and disconnect all

cables connecting the stock cooler to the PCB.

Always remove the stock cooler slowly - it might be ﬁrmly

glued to the PCB with thermal pads.

You will need the following tool:

Phillips Head Screwdriver

STEP 1

STOCK COOLER BACKPLATE

OPTION 1

I/O BRACKET SCREW

- 9 -

STEP 2

CLEANING THE PCB

Wipe off the remains of the original thermal compound using a

nonabrasive cloth or Q-tip, as shown in the sample image, until the

components and circuit board are completely clean. EK recommends

the use of denatured alcohol for removing TIM leftovers. After that,

remove all remaining stock thermal pads from the PCB.

OPTION 2 – GPU Versions With a Backplate

Use the Phillips head screwdriver to remove the twelve marked screws

and the Stock Cooler Backplate from the backplate’s side.

Carefully detach the PCB from the stock cooler and the backplate, and

disconnect all cables connecting the stock cooler to the PCB.

Always remove the stock cooler slowly - it might be ﬁrmly

glued to the PCB with thermal pads.

STEP 1

OPTION 2

STOCK COOLER BACKPLATE

BACK PL ATE

- 10 -

BACK PL ATE

PREPARING THE WATER BLOCK FOR INSTALLATION

STEP 1

Unscrew eight (8) Screws AX1 M2.5 x 8 as shown in the image.

Remove the backplate together with eight (8) Screws M2.5 x 8 AX1

and backplate standoffs. Standoffs must stay on Screws M2.5 x 8

AX1. Remove cardboard. Save the backplate set for later steps.

Do not remove standoffs from screws! In case the

standoff detaches from the screw, replace it with a

spare one. When replacing the standoff make sure

that you screw it on the AX1 M2.5 x 8 screw. Do

not push the standoff onto the screw AX1 M2.5 x 8!

STEP 1

For this step, you will need:

Phillips Head Screwdriver

M2.5 x 8 AX1 SCREW

BACK PL ATE

STAN DO FF

DO NOT

REMOVE

STANDOFFS

FROM

SCREWS!

CARDBOARD

Altri manuali per Vector2 XC3 RTX 3080 D-RGB

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali EK-Quantum Hardware per computer

EK-Quantum

EK-Quantum Vector RX 6800/6900 D-RGB - AMD Radeon... Manuale utente

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manuale utente

EK-Quantum

EK-Quantum Velocity 2 D-RGB AM4 Manuale utente

EK-Quantum

EK-Quantum Vector Strix RTX 3080 Backplate Manuale utente

EK-Quantum

EK-Quantum Reflection PC-O11D Mini D5 PWM D-RGB Manuale utente

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector2 Strix RTX 3080 D-RGB Manuale utente

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector Strix RTX 3080 Backplate Manuale utente

EK-Quantum

EK-Quantum Momentum ROG Rampage VI Encore Manuale utente

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector Strix RTX 3090 Backplate Manuale utente

EK-Quantum

EK-Quantum Vector XC3 RTX 3070 D-RGB Manuale utente

EK-Quantum

EK-Quantum Momentum2 ROG Strix X570-i Gaming D-RGB Manuale utente

EK-Quantum

EK-Quantum Reflection2 7000D D5 PWM D-RGB Manuale utente

EK-Quantum

EK-Quantum Velocity2 D-RGB -LGA 1700 Manuale utente

EK-Quantum

EK-Quantum Vector FE RTX 3070 Ti D-RGB + Backplate Manuale utente

EK-Quantum

EK-Quantum Velocity2 D-RGB -LGA 1700 Manuale utente

EK-Quantum

EK-Quantum Vector Strix RTX 3070 Backplate Manuale utente

EK-Quantum

EK-Quantum Power2 Kit P360 Series Manuale utente

EK-Quantum

EK-Quantum Vector Strix RTX 3070 Backplate Manuale utente

EK-Quantum

EK-Quantum Vector RTX 3080/3090 Backplate Manuale utente

EK-Quantum

EK-Quantum Vector2 FTW3 RTX 3080 D-RGB Manuale utente

EK-Quantum

EK-Quantum Vector FTW3 RTX 3080 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente